|
| 1 | Dismantling of wall and ceiling boards, (fibre, pulp, insulation etc) or insulation boards / slabs / blankets of any thickness including cover fillets, stuctural steel frame etc, complete all as specified and directed. |
| 2 | Demolition of brick work or stone boulder masonery, built in cement mortor including all quoins, arches, pillars etc, complete all as specified and directed. |
| 3 | M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed. |
| 4 | Dismantling of wrought iron or mild steel work of any description, complete all as specified and directed. |
| 5 | M&L for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS:1161-1998 Grade ST-240, complete all as specified and directed. |
| 6 | M&L for mild steel roof trusses (framed), trusses purlins, cranes / ganttries, rails & fastering & heavy bracket cleats (including distannce pieces, cleats etc.), conforming to Fe-410-W (Gde-E-250 Quality-A), complete all as specified and directed. |
| 7 | Taking down cement plaster of any description on bricks, PCC block or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 8 | M&L for 15mm thick rendering on fair faces or brick work or concrete surfaces in cement mortar 1:4 with using water proofing compund and finishing the surface even and smooth without using extra cement, complete all as specified and directed.Note :- WPC shall be measured and paid separately under respective item of this BOQ. |
| 9 | Supply only integeral water proofing compound. |
| 10 | M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 11 | M&L for preparation of new surfaces of walls and applying two coats of distemper oil emulsion over 2-3mm thick wall care putty, complete all as specified and directed. |
| 12 | M&L for preparation of surfaces and applying two coats of cement base paint over newly plastered surfaces of wall including one coat of primer, complete all as specified and directed. |
| 13 | M&L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in floor and finished the surface even and smooth with using extra cement, complete all as specified and directed. |
| 14 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 15 | M&L for 7-8mm thick non skid coloured ceramic tiles, area of each tile exc. 0.11 Sqm but not exc 0.18 Sqm as in floor finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 16 | M&L for 10mm thick vitrified ceramic coloured tiles (square or rectangular), polished, area of each tile not exceeding 0.36 Sqm in floor, skirtings etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed/ plaster in CM 1:4, complete all as specified and directed. |
| 17 | M&L for glazed ceramic tiles (coloured) on vertical surfaces, size of each tile 450mm x 300mm x 6-7mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering in cement mortar 1:4 as in backing coat for wall tiles, complete all as specified and directed. |
| 18 | M&L for preparation of new steel or iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 19 | M&L for preparation of old steel or iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. |
| 20 | S&F in repair/ replacement of solid PVC Wall Lining (Wall Panelling) consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement & fixing at site on PVC frame as per specification and directed. |
| 21 | M&L for complete removal of existing treatement by scraping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia 7\\" / 9\\" to make the surface free from dust, loose paint etc. by skilled labour, complete all as specified and directed. |
| 22 | M&L for waterproof cement based putty @ 1 Kg (undiluted) per Sqm of average thickness 1mm over the plastered / old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit for above to make the surface free from dust etc. by skilled labour as per following steps :-Step 1 : Mix the putty powder by adding water as per manufacturer's instructions and mix it with putty mixer with the capacity of min 2.5 Kg putty per minute.Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3 : Allow 6-8 hrs time dry the putty surface. |
| 23 | M&L for applying two coats of oil bound distermper using airless technology with max working pressure of 3300 PSI and capable of operating single spray gun with max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro paint manufacturer and as mentioned and accessories for applying distermper should be able to spray in hard to reach areas and penetration of distemper on the surface, complete all as specified and directed. Note :- Sanding of surface to be done by mechanical sander with 1500-2700 RPM with internal dust extraction system for clean environment certified by paint manufacturer. |
| 24 | M&L for one coat of acrylic water based exterior grade primer @ 0.8 ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting subsequent coats, complete all as specified and directed. |
| 25 | M&L for two coats water based premium acrylic smooth exterior emulsion of approved colour with silicon additive and colour stay technology, excellent Drit pick up resistance with low VOC less than 50 gram/litre as per LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted with water as per manufacturer's instructions applied over priming coat with fully automatic airless stray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint, complete all as specified and directed. |
| 26 | M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, plasters etc. including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and aplpying one coat of white wash on wall, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 27 | M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, plasters etc. including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and aplpying one coat of white wash on wall, complete all as specified and directed. Please Enable Macros to View BoQ information |
