|
| 1 | S&F 2nd class HW scantlings, clean sawn supplied and fixed, with and including dismantling existing u/s timber scantling framed work 40sq.cm and over section, in any position, complete all as specified and as directed. |
| 2 | Taking down & refixing in old or new position of 2nd class HW scantlings, clean sawn, with and including dismantling existing u/s timber scantling framed work 40sq.cm and over section, in any position, complete all as specified and as directed. |
| 3 | M&L for Preparing surface of wood and wood based materials, new or old, of any description and girth and treated with two coats of creosote oil, complete all as specified and as directed. |
| 4 | S&F Mild Steel Corrugated Galvanised Steel Sheet 0.45mm thick of class 8, grade of zinc coating 275, as in roof covering with two corrugation side laps fixed with coach screws & washers, with and including dismantling u/s AC sheet roofing and removing rubbish off the premises, complete all as specified and as directed. |
| 5 | S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle, channel, hollow sections or flat sections) including distance pieces & cleats, conforming tograde Fe 410-W Gde E-250 quality 'B', complete all as specified and as directed. |
| 6 | S&F Mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165, with and including dismantling existing wrought iron or mild steel work of any description, complete all as specified and as directed. |
| 7 | M&L for Cement concrete roofing tiles, rustic red colour, 420mm x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry as in roofing, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 8 | M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 9 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, with and including taking down existing u/s AC sheet roof of any description, complete all as specified and as directed. |
| 10 | M&L for PCC type C0 [1:3:6] using 12.50mm graded stone aggregate) as in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, finished plain fair faces, including demolition of old cement concrete of any type, complete all as specified and as directed. |
| 11 | S&F Aluminium Composite Pannel board of 4mm thick, comprising of a core containing not less than 70% non combustible mineral filling, sandwiched between two skins of 0.50mm thick aluminium alloy PERALUMAN-100 of weight not less than 7.6kg/Sqm, with all sub structures, anchors, hardware and all fittings, fixed over and including aluminium section of size 35x25x2mm and 1.0m x 0.30m panel with and including necessary frame work, screwing & scaffolding, fixed with screws / nails, with and including dismantling existing u/s boarding of any description, complete all as specified. Note: Measurements shall be taken as flat as fixed without any allowance for laps. |
| 12 | M&L for Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed. |
| 13 | M&L for False ceiling with High Pressure Steam Cured (HPSC) 4mm thick Non Asbestos Fibre Cement ceiling boards fixed with and including supply & fixing powder coated aluminium snap grid of size 605mmx605mm consisting of 25X25X1.25mm aluminium angles and TEEs of size 35x25x1.25mm with galvanised wire of required length and 6mm dia hanger grid suspended from trusses/ ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying three coats of white wash on ceiling surface, with and including taking down existing u/s ceiling with frame work of any description, complete all as specified and as directed. |
| 14 | M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed. |
| 15 | M&L for 10mm thick Rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finish the surface even and smooth without using extra cement, complete all as specified and as directed. |
| 16 | M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 mixed with and including water proofing compound @3% of weight of cement and finish the surface even and smooth without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed. |
| 17 | M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer with and including a layer of wall care putty, complete all as specified and as directed. |
| 18 | M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of new plastered surfaces of any description, all as per manufacturer's instructions, complete all as specified and as directed. |
| 19 | M&L for complete removal of existing treatment on old walls with wire brush, scrapping down smoke soot, mould, moss nad efforescent salts, oils & greasy spots etc., and two coats of oil bound distemper over a coat of alkali resistant primer with and including a layer of wall care putty and including preparation of old surfaces of any description, complete all as specified and as directed. |
| 20 | M&L for complete removal of existing treatment on old walls with wire brush, scrapping down smoke soot, mould, moss nad efforescent salts, oils & greasy spots etc., and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of old surfaces of any description, complete all as specified and as directed. |
| 21 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.06Sqm but not exceeding 0.11Sqm, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed. |
| 22 | M&L for Premium quality, joint free ceramic glazed coloured wall tiles of 7 to 8mm thick (square / rectangular) area of each tile not exceeding 0.18Sqm, on vertical surfaces such as dado and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over & including 10mm thick rendering in CM 1:3 and including taking down existing dado/skirting with backing mortar, complete all as specified. |
| 23 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exceeding 0.36Sqm, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed. |
| 24 | M&L for Machine cut Kota stone slab 18-20mm thick, as in flooring over with and including 20mm thick cement screed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match shade of the slab, including cutting, waste, grinding, rubbing and polishing, with and including demolition of existing floor tiles of any description, complete all as specified. |
| 25 | S&F Machine cut kota stone slab 18-20mm thick, as in vertical surfaces such as skirting/dado, laid over and including 15mm thick backing coat in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, with and including demolition of existing skirting/dado, complete all as specifed and as directed. |
| 26 | M&L Mirror polishing on existing Kota stone flooring, where ever required to give high gloss mirror polish finish, complete all as specified and as directed. |
| 27 | M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 mtres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 28 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area n. exc. 1.5sqm each, complete all as specified and as directed. |
| 29 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed. |
| 30 | M&L for Second class hard wood plain solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed. |
| 31 | M&L for Factory made 2nd class hard wood plain, framed, panelled door shutter 35mm thick, two panels with lock rail and panels of 12mm thick plywood BWR 9 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkats, complete all as specified and as directed. |
| 32 | M&L for Factory made 2nd class hard wood Glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (with divided in to square with plain, chamfered or rounded, mitered and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats, complete all as specified and as directed. |
| 33 | M&L for Factory made 2nd class hardwood 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc for windows, ventilators for etc provided with stiles and rails and divided into square with plain chamfered or rounded mitred and rebated sash bars any numbers size of members of shutters as specified in SSR Part-I Section 8 Clause 8.24(b) supplied and fitted to chowkats, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 34 | M&L for Factory made 2nd class hardwood 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc for windows, ventilators for etc provided with stiles and rails and divided into square with plain chamfered or rounded mitred and rebated sash bars any numbers size of members of shutters as specified in SSR Part-I Section 8 Clause 8.24(b) supplied and fitted to chowkats, complete all as specified and as directed. Please Enable Macros to View BoQ information |
