|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 2 | Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed with a lead in a 50 meter including stacking of useful material if available : Ordinary rock |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. In depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 4 | Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside and outside. In the middle area the termitube to be installed at an interval of 1.00 Mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. The plinth area of the area treated will be measured for payment. |
| 5 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 6 | Random rubble dry stone Kharanja under floor. |
| 7 | Providing and laying in position cement concrete including curing compaction etc . Complete in specified grade excluding the cost of centering and shuttering. All work up to plinth level using crusher broken aggregate M10 grade Nominal Mix ( with graded stone aggregate 20mm nominal size) |
| 8 | Providing and laying in position Ready mix concrete manufactured in fully automatic Batching Plant and transported to site in transit mixer for having continous agitated mixer, manufactured as per approved mix design of specified grade of RCC work including pumping of R.M.C. from transit mixer to site of laying , exculding the cost of centering, shuttering and reinforcement with all lead and lift including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge. All works upto floor V floor M20 grade Design Mix by using cement as per codal provision. Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix |
| 9 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix Add extra for providing richer mixes respectively at all floor levels Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 10 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 11 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. |
| 12 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 13 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :Grid roofing with panel area less than 2.25 Sqm. (contact area to be measured). |
| 14 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Columns, pillars, posts and struts etc. |
| 15 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 16 | Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 17 | Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 18 | 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) |
| 19 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. |
| 20 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 25mm thick. |
| 21 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats) |
| 22 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. |
| 23 | Providing and applying superior quality emulsion for wall painting with Velvet touch/Royal paint etc of approved brand and manufacture to give an even shade with putty and preparation of surface applying with the help of paint roller the work complete in all respect as per direction of Engineer-incharge. New Work Three or More coat |
| 24 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specifications including primer coat and protecting coat including scaffolding and safety provision Trowel Finish av. thickness 2000 to 2500 microns. |
| 25 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work |
| 26 | Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification .75 mm thick |
| 27 | Providing and fixing 1st quality MAT & GLOSSY finished ceramic tile confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). size 600mmx600mm |
| 28 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed Extra for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 29 | P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.size 600 mm X 1200 mm |
| 30 | Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm |
| 31 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, includingrubbing and polishing complete For area of each slab upto 2001 Sqcm |
| 32 | Extra for Mirror polishing on terrazzo/Kota stone work where ever required to give high gloss finish complete. |
| 33 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Rajasthan Black Above 3601 Cm2 Slabs |
| 34 | Extra for providing edge moulding to 16-18 mm thick marble stone counters, vantities etc. including machines polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge Granite work/kota stone. |
| 35 | Extra for providing edge moulding to 16-18 mm thick marble stone counters, vantities etc. including machines polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge Granite work/kota stone. Half Edge moulding |
| 36 | Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugswith split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-incharge :Profile E |
| 37 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : 35 mm thick .Decorative teak veneer both side Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area of the shutter to be measured). Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) |
| 38 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : 35 mm thick .Decorative teak veneer both side Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area of the shutter to be measured). Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) |
| 39 | Providing & fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat, hold fasts of size 250 x 40 x 3mm fixed with M.S. bolt 5mm dia 50mm long duly embedded in cement concrete M-15 grade : Ivory coast wood Grade I |
| 40 | Providing and fixing fully panelled/partly panelled/ double leaf shutter frames for doors as per approved design and drawings with approved ordinary C.P./ oxidised steel fittings as per Annexure - 'A' and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete :35 mm thick Ivory coast wood grade I |
| 41 | Providing and fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture as per direction of Engineer-in-charge of size 595 X 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm) consisting of main „T‟ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.33 mm thick (minimum) sheet, 1200mm centre to centre, and cross „T‟ of size 24X32mm made out of 0.33mm (Minimum) sheet,1200mm long spaced between main „T‟ at 600mm centre to centre to form a grid of 1200X600mm and secondary cross ‟T‟ of length 600mm and size 24X32mm made out of 0.33 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edged calcium silicate ceiling tiles of approved texture in the grid including cutting /making opening for services like diffusers, grills, light fitting, fixtures, smoke detectors etc., wherever required, Main „T‟ runners to be suspended from ceiling using 50 mm long M 6 dash fasteners, 6mm G.I. fully threaded rods with galvnised steel L cleat level adjusters of size 80x25x2mm, spaced at 1200mm centre to centre long main „T‟ bottom exposed with 24mm of all T-sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs)having area less than 0.30 Sqm. The calcium silicate ceiling tiles shall have NRC. |
| 42 | Providing and fixing of wall paneling on grid made out ofPVC profile section of size 21x17mm with a wall thickness of 1.5mm+/-0.2mm,fixed on the existing wall with wood screw of size 50mm X 8mm with rowel plug at a spacing of 900mm center.uPVC profile section of size 150mm X 10mm with a wall thickness of 1.0mm+/-0.2mm to be fixed on the grid by self tapping screw of size 19mm X 6mm.Necessary cutouts for electrical connection to be provided at required places. The edge and periphery, finally to be covered by extruded PVC beading section of size 28mm X 12mm with a wall thickness of 1.0mm+/-0.2mm complete as per manufacture‟s specification and direction of Engineer-in-charge. |
| 43 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 44 | Making grooves as per design in plaster 10mm to 20mm wide. |
| 45 | Providing non slip grooves to granite/ kota stone flooring, counters, vanities etc. using groove cutter V type including machine polishing to groove to give high gloss finish etc. complete as per design approved by engineer in charge |
| 46 | Providing and fixing steel gate grating and grills made of angles, tees, square bars or flats black pipe with holdfast and fittings complete as per deign and drawing including cutting welding and fabrication with priming coat of red oxide. |
| 47 | Extra if square,rectangular hollow tubelar sections are used or grill made by flats only |
| 48 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. |
| 49 | Providing and applying P.U. paint of apporved brand and manufature to even shade. Two or more coats on New works. |
| 50 | Providing and applying Melamine polish on teak wood work of approved brand and manufacture to give an even shade with two or more coats by compressor including sand papering, wood filler coat etc complete in all respect: New Surface |
| 51 | Providing and fixing of uPVC Sliding windows: Frame Madefrom the Extruded uPVC Window Profile Section of size106w x 50h mm having outer wall thickness of 2.5mm (+/-0.2mm) and 3 box multi-chamber construction, White infinish, duly reinforced with 1.2 mm thick GI section. Frameshall have three track configuration, two for sliding of windowshutter and one for mosquito mesh shutter. Vertical member offrame which bears the sliding shutter load shall havealuminium rail/track for smooth sliding of shutter rollers. Allthe four corners shall be mitered cut & thermal welded so as toform window frame. Frame shall be milled with drain and airequalizer hole in order to be water tight and for drainage ofaccumulated water, if any, to outer side.Shutter : The shutter of sliding window shall be made of 39wx 69h mm Extruded 3 box multi- chamber uPVC WindowProfile Section of white colour having outer wall thickness of2.5mm (+/- 0.2mm) provided with reinforcement of 1.5mmthick GI section duly mitered cut & thermal welded at allcorners and fitted with uPVC glazing bead of size 22 x 20 mm |
| 52 | Providing and fixing of uPVC casement fixed windows or ventilators manufactured in ISO 9001:2000 & 14001:2004 certified company. Frame : Made from the Extruded uPVC Window Profile Section of size 60 x 60mm having outer wall thickness of 2.25mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2mm thick G/J/U/O TYPE GI section. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Fix Mullion made of 76 x 60mm uPVC Profile Section with steel reinforcement shall be provided in windows as per the requirement. Frame shall have „O‟ type EPDM gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter. Glazing bead of size 34 x 20mm with „K‟ & „O‟ type inner and outer EPDM weather seal gaskets alongwith 5mm thick ISI make plain float glass.All welding joints of frame and shutter shall be cleaned and milled with the CNC mechanism to provide uniform grooved finish on all visible joints. Hardware : Installation at Site : Complete window is to be installed on site with 10 x 100mm fastners with white cap in existing pre-finished wall cut-out cemented to glass level planeat all height & width and silicon glue is applied to fill up the crevices between wall and window frame. Complete in all respect as per the drawing and specifications and direction of engineer-in-charge. |
| 53 | Providing and fixing of openable uPVC Doors with or withoutfix top: Frame Made of Extruded uPVC Window ProfileSection of size 60w x 70h mm having outer wall thickness of2.75mm (+/- 0.2mm) and 3 box multi-chamber construction,Laminated (colour) finish, duly reinforced with 1.2mm thickGI section. All the corners shall be mitered cut & thermalwelded so as to form door frame. Fix Mullion made of 60w x80h mm uPVC Profile Section with steel reinforcement shallbe provided for the top fix portion of the doors or in case ofthe doors having more than two openable shutters, as per therequirement / drawing. Frame of openable door shall have coextruded EPDM/TPE-E gasket fitted in in-built groove offrame profile for proper air & sound insulation of the shutter.Shutter : The shutters of openable door shall be made of 60w x95h mm Extruded 3 box multi-chamber uPVC Window ProfileSection of laminated( colour) having outer wall thickness of2.75mm (+/- 0.2mm) provided with reinforcement of 2.0 mmthick GI section duly mitered cut & thermal welded at allcorners, provided with center mullion (if specified in drawing)of size 60w x 80h mm uPVC Profile Section and fitted withuPVC glazing bead of size 36 x 20mm with inner and outer co-extruded EPDM/TPE-E weather seal gaskets alongwith 6mm thick ISI make plain float glass. All welding joints of frame and shutter shall be cleaned and milled with the CNC mechanism to provide uniform grooved finish on all visible joints. Hardware: Each openable door shutters is to be fixed with three load beading butt hinges and locking of doors is to be provided with multi-point transmission gear (ESPAG) with white finish powder- coated lockable handle. Installation at site: Complete door is to be installed on site with 10 X 100mm fastners with white cap in existing pre-finished wall cut-out cemented to glass level plane at all height & width and silicon glue is applied to fill up the crevices between wall and door frame. Complete in all respect as per the drawing and specification and direction of engineerin-charge |
| 54 | Providing and Fixing Chiken wire mesh at the joint of masonry members/ R.C.C. Members with Nails complete in all respect. |
| 55 | Providing and laying brick kharanja on roofs with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound in square pattern 75mm to 100mm thick average |
| 56 | Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish :25 mm thick. |
| 57 | Finishing with neat cement punning |
| 58 | Making khurras 450 x 450mm with average minimum thickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 59 | Providing&FixingCommercial Ply as per IS710 : 1976 BWRof approved make formakingwardrobe/shelves and otherfurniturewithfevicol&nailscomplete asperapproved by engineer in charge. (i) 18 mm thick |
| 60 | Providing and Fixing Aluminium composite panel of approved make 3mm thick with 0.5mm thick skin & PVDF coated approved shade for wall panelling. Main framing work to be done using 50mmx25mmx1.6mm tubular section of approved make. Stainless steel screw to be used to fix the ACP panel to be fixed to the main frame with industrial adhesive tape and panel groove to be sealed with weather proof silicon sealant suitable for glass/aluminium etc. complete in all respect as approved by Engineer-in-charge. |
| 61 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 kg//sqm .This layer will be allowed to air cure for 4 hours. (ii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed by water curing for 48 hours. The rates includes preparation of surface treatment & sealing of all joints ,corners, junction with polymer mixed slurry. |
| 62 | Providing and fixing expansion joint board for building RCC column beams, walls, slab of Polyethylene foam of density 30 to 35 Kg/m3 of Armour Board. 50 mm Thick |
| 63 | Providing and fixing 150 mm wide sheet covering overexpansion joints with iron screws as per design to match the colour / shade of wall treatment. Aluminum fluted strips 2 mm thick |
| 64 | Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor W.C. orissa pan with 100 mm vitreous china P or S trap (Size 580x440 mm.) |
| 65 | Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floor Double Syphonic European W.C. with mounted W.V.C. flushing cistern of 10 litre capacity complete with all necessary internal fittings with Hydraulic seat cover. |
| 66 | Providing & Fixing premium qulaity WVC Urinal with PVC waste pipe, dome couplings, concealed iron brackets or screws etc. complete. Providing & Fixing premium qulaity WVC Urinal with PVC waste pipe, dome couplings, concealed iron brackets or screws etc. complete. |
| 67 | Providing & Fixing premium qulaity WVC Wash basin with C.I. brackets duly painted & 32 mm C.P. brass waste coupling of approved make with PVC waste pipe complete Size 550 mm x 400 mm dia for counter top |
| 68 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Pillar Cock 15 mm nominal size |
| 69 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge .Jet Spray (Premium heavy Quality) as approved by Engineerin-Charge |
| 70 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Health focet (Premium heavy Quality) as approved by Engineer-in-Charge |
| 71 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Long body Bib Cock 15 mm nominal size |
| 72 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Soap dish |
| 73 | Providing & Fixing Premium quality Bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by Engineer in Charge. |
| 74 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Bib Cock with long thread 15 mm nominal size |
| 75 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Sink cock with swinging casted spout (table mounted ) 15 mm nominal size |
| 76 | Providing and fixing premium quality Two way Bib cock 15mm with wall flange complete as per sample approved by Engineer in charge |
| 77 | Providing and fixing premium quality Angular stop cock 15mm with wall flange complete as per sample approved by Engineer in charge |
| 78 | P & F C.P. brass Urinal Spreader for Large Urinal of heavy duty of approved make as per direction of Enginner-in-Charge |
| 79 | Providing & Fixing premium quality waste coupling 32mm half thread as per approved by Engineer in Charge |
| 80 | P & F Bevelled edge Mirror/mirror with teak wood lipping round of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. |
| 81 | P & F grating of approved quality/make C.P. brass with frame (heavy) and superior quality Synthetic Material(PTMT) of approved quality/make Square 150 x 150 x 8mm. (Anti Cockroach) |
| 82 | P&F liquid soap container with brackets complete of approved make C.P. brass |
| 83 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Revolving type towel ring |
| 84 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Paper holder |
| 85 | P&F ball cock (IS:1703 mark) with rod and PVC ball complete brass Wt. 300 gm. 15mm. |
| 86 | P/F 15mm dia connection pipe of approved quality/make PVC pipe with C.P. brass nuts upto length 600 mm. |
| 87 | P/F flush cock/flush valve (IS: 9758 mark) for WC of approved quality make C.P. brass half turn Concealed 25mm nominal bore. |
| 88 | P/F full way valve (IS:778 mark) or wheel valve of approved make Gun metal 25mm nominal bore. |
| 89 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 50mm nominal bore. |
| 90 | Providing & fixing PVC storage tank (IS: 12701 marked indicating the BIS license No. ) of approved make with cover, 25mm dia. 1 mtr. long G.I. over flow pipe and 25 cm. long washout pipe with plug and socket including making connections etc. complete of approved design,1000 litres capacity. |
| 91 | P/F rigid PVC pipe (IS:4985 mark) class II (4 Kg./Cm2) approved quality/make incl. jointing the pipe with solvent cement rubber ring and lubricant 63 mm dia. |
| 92 | _do__ 75mm dia. |
| 93 | --do-- 110mm dia. |
| 94 | __do__ 160mm dia. |
| 95 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 75 mm dia |
| 96 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110 mm dia |
| 97 | Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. PVC pipe 110 mm dia |
| 98 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make Coupler 75mm dia |
| 99 | (---do---) coupler 110mm |
| 100 | (---do---) Bend 87.5 Dg. 75mm dia |
| 101 | (---do---) Bend 87.5 Dg. 110mm dia |
| 102 | (---do---) Bend 45 Dg. 75mm dia |
| 103 | (---do---) Bend 45 Dg. 110mm dia |
| 104 | (---do---) Door Bend 87.5 Dg. 75mm dia |
| 105 | (---do---) Door Bend 87.5 Dg. 110mm dia |
| 106 | (---do---)Extra Round Jali 110mm dia |
| 107 | (---do---)Vent Cowel 110mm dia |
| 108 | (---do---)Single 'Y' with Door 110mm dia |
| 109 | (---do---)Single Tee 110mm dia |
| 110 | (---do---)Single Tee with Door 110mm dia |
| 111 | P/F rigid PVC pipe fittings (IS:4985 mark) of approved quality/make incl. jointing the pipe with solvent cement rubber ring and lubricant Reducer 110x75 mm110mm |
| 112 | ---do--- Plain Tee 75mm |
| 113 | ---do--- Plain Tee 110mm |
| 114 | (---do---) Plain Tee 160mm |
| 115 | ---do--- Door Tee 75mm |
| 116 | ---do--- Door Tee 110mm |
| 117 | (---do---) Door Tee 160mm |
| 118 | ---do--- Bend 87.5, 75mm dia. |
| 119 | ---do--- Bend 87.5, 110mm dia. |
| 120 | (---do---) Bend 87.5, 160mm dia. |
| 121 | --do—Door Bend top side 75mm |
| 122 | ---do--- Door Bend (Top side) 110mm dia. |
| 123 | (---do--- )Door Bend (Top side) 160mm dia. |
| 124 | (---do---) coupler (Socket) 75mm |
| 125 | (---do---) coupler (Socket) 110mm |
| 126 | (---do---) coupler (Socket) 160mm |
| 127 | --do— Vent Cowel 110mm dia. |
| 128 | --do-- Gully trap 110mm dia. |
| 129 | (--do—) Bend 45 75mm |
| 130 | (--do—) Bend 45 110mm |
| 131 | (--do—) Bend 45 160mm |
| 132 | (--do—) Pipe Clip 75mm |
| 133 | (--do—) Pipe Clip 110mm |
| 134 | (--do—) Pipe Clip 160mm |
| 135 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) 20 mm nominal size |
| 136 | (--do--)25mm nominal size |
| 137 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 50 mm nominal size |
| 138 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work).25mm nominal size |
| 139 | (--do--)40mm nominal size |
| 140 | (--do--)50mm nominal size |
| 141 | Construction of Manhole in all types of soil inner size 1.5x1.2 M with 450mm thick masonry in C.M. 1:6, 10 cm thick cement concrete 1:5:10 in foundation 20mm thick inside plaster in C.M. 1:6 finished with floating neat cement 50mm thick M-15 grade C.C. flooring making channels 80mm thick stone slab covering with 40mm thick stone M-15 grade C.C. flooring, Ferro cement cover with frame of 450mm dia earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. Lead as per desing depth upto 1.5 M. |
| 142 | Construction of Chamber in all types of soil 300mm thick masonry in C.M. 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick inside plaster in C.M. 1:6 finished with floating neat cement 50mm thick M-15 grade C.C. flooring earth work etc. complete as per design incl. disposal of surplus earth within a lead of 50 mtr. Inside size 600 x 450mm depth upto 0.5 M Cement cover with frame. |
| 143 | P &F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor. 1.0 mm thick stainless steel AISI -304 & IS 13983-1994kitchen sink of approved make as per Engineer-in-charge with large waste coupling Overall size (inches) 24 x 18 x 8 Bowl size (inches) 20x16x8 |
| 144 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthworkcomplete as per approved drawing including disposal of earth within a lead of 50 mtr.:Size 300 Cm. dia outside & 300 Cm. depth . |
| 145 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M- 15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nosstone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 400 x140x150 cm.(for 50 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10mm ϕ @15 cm c/c bothways including shuttering complete in all respect. |
| 146 | Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe:200 mm Nominal bore. |
| 147 | Supply of ERW M.S. black casing pipe ISI marked(IS:4270/1992) of grade Fe410 of following sizes at site of work. 200 mm Nominal bore of pipe |
| 148 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size:200mm dia |
| 149 | Construction of tubewell up to 100m depth and above to accomodate housing and assembly pipe in all types of alluvium strata by rotay drilling method with \\"code of practice for construction and testing of tubewells (IS:2800 (Part-II) : 1991 and IS:2800 (Part-II) :1979 both amended up to date) with supply of bail plug if necessary.The work will not include cost of housing pipe and strainer pipe assembly cost, gravel and development work. Work would be deemed completed only after obtaining sound free water during pumping. 200 mm nominal bore |
| 150 | Construction of Recharge Shaft in filter pit including Earth work Excavation , lifting excavted earth with all lift and 50 m lead and centering & shuttering evenever required. Diameter 900 mm |
| 151 | Supply & fixing Pre-cast RCC Rinngs at themouth of recharge shaft of M20 mix with 40mm thickness Diameter 900 mm |
| 152 | Supply and lowering vent air pipe 63mm diarigid PVC pipe(IS 4985) mark class II (4kg percm2 ) with required all necessary fittingsincluding perforation of 3 to 5 mm size allaround the pipe at a distance of 180 to 220mmin zig zag fashion and making air vent at topcomplete as per direction of Engineerincharge. |
| 153 | Supply & lying River-gravels of following sizesin recharge shaft, filter pit after screening &washing from kachha shift without deduction ofvoids Size 9 to 12 mm |
| 154 | Supply & lying River-gravels of following sizesin recharge shaft, filter pit after screening &washing from kachha shift without deduction ofvoids Size 3 to 5 mm Please Enable Macros to View BoQ information |
