|
| 1 | SH-I Electrical WorkWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(a) Group B |
| 2 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.(a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 3 | (b) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 4 | (c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 5 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, “C” curve including connections, painting etc. as required. |
| 6 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 7 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 8 | Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, NonPlenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.(a) 1 run of cable |
| 9 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)(a) 12 way, Double door |
| 10 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a) Single pole |
| 11 | Supplying and fixing following rating, following pole, 240 /415V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a) Single pole and neutral -32 Amp. |
| 12 | Supplying, installation, testing and commissioning of following size 4K UHD TV with 3840 x 2160 Ultra HD Resolution, AI Processor 4K, WebOS/Android OS, Powerful Speaker, HDMI Ports, USB Ports, Wi-Fi & Bluetooth supported etc. complete as required.(a) 65 inch (164cm) |
| 13 | (b) 75 inch (164cm) |
| 14 | Supplying, installation, testing & commissioning of 15 watt LED cob garden spike light, aluminium body, color temperature: 3000K, IP rating: 66 etc. complete as required. |
| 15 | Supplying, installation, testing & commissioning of 6-8 watt step light, aluminium body, color temperature: 3000K, IP rating: 65/66 etc. complete as required. |
| 16 | SH - II of UPS System Online UPS - Input supply: Single Phase, Output Supply: Single Phase. Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) ON LINE Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. The UPS systems shall be Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE.The operating efficiency of the UPS systems shall be >95% at 100% non-linear loads. Current total harmonic distortion (ITHD)/ total demand distortion (TDD) on the input grid shall be < 5% at 100%load. (The required LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0. 99 and output power factor shall be unity (i. e. kw rating of the UPS shall be kva rating x 1) however UPS shall be suitable to take load at 0. 7 laging to 0. 7 leading power factor loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine wave single phase 220/230/240 Volt, 50 Hz +/- 0. 2Hz, Overload capacity of 120% for 10 mins and 150% for 1 minute. Operating temperature 0 to 40 0C, Relative humidity 0-95% non condensing, noise level less than 60db at 1 meter distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over charging, output over current, short circuit, battery deep discharge, 10 KV surge.Display for watt/VA, Amp and Voltage power parameters etc. UPS shall comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 & 3) . The UPS should be with IGBT Based Inverter Technology, Communication RS232/ RS485/ SNMP port open protocol for BMS integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable rating and interconnecting copper conductor cable of suitable size and connectors and all required accessories are inclusive in the cost. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc. (a) 10KVA (Each Power module shall be < 10 KVA) |
| 17 | SH-II Audio Video System Supply, Installation, testing & commissioning of High performance Digital Wired Desktop Chairman Unit with High-directivity gooseneck condenser micro phone with red LED indicator ring, Microphone stem length 220mm, Low-voltage DC24V operation for enhanced safety, Signal to Noise ratio ≥65dB, Chairman-specific controls: Priority override, Delegate microphone mute, Speech request approval and management, 1.8-inch color TFT display screen showing real-time meeting data, Third-party system integration via RS-232, enabling camera tracking and remote microphone control, Optimal speaking distance: 10 - 40 cm; intelligent noise suppression effective up to 1 meter, etc complete as required. |
| 18 | Supply, Installation, testing & commissioning of High performance Digital Wired Desktop Delegate Unit with High-directivity gooseneck condenser micro phone with red LED indicator ring, Microphone stem length 220mm, Low-voltage DC24V operation for enhanced safety, Signal to Noise ratio ≥65dB, 1.8-inch color TFT display screen showing real-time meeting data, Third-party system integration via RS-232, enabling camera tracking and remote microphone control, Optimal speaking distance: 10 - 40 cm; intelligent noise suppression effective up to 1 meter, etc completed as required. |
| 19 | Supplying, Installation, testing & commissioning of High performance digital wired conference controller unit Directly connects up to 60 units, expandable to 250 units with extension modules, Maximum power consumption 120W, RS-232 control support for third-party central control integration (camera tracking, microphone management, and meeting modes), 4-in/1-out seamless HDMI switcher, supporting 4 cameras at 1080p@60Hz with zero switching delay, PELCO-D, PELCO-P, VISCA via RS-485 interface, etc completed as required. |
| 20 | Supplying, Installation, testing & commissioning of Two way full range coaxial ceiling /wall speaker with 5.25” Polypropylene woofer with rubber surround for extended low frequency response, 0.75” Polycarbonate tweeter with swivel mount for high frequency directivity, Driver Power Handling 30W RMS / 60W Program / 120W Peak, High performance 100V LMT inbuilt – 15W and 10W selectable via switch, Calculated Max SPL 104dB Continuous / 107dB Program / 110dB Peak, etc. as required. |
| 21 | Supplying, Installation, testing & commissioning of Mixer amplifer 4-16 ohm,with 120W RMS output power, 70V/100V output,USB/FM/Bluetooth Mediaplayer, 2 Aux and 3 microphone inputs,Frequency Response: 35Hz to 20 kHz, Total Harmonic Distortion: 0.05%, Intermodulation Distortion: <0.35%(60Hz and 7kHz at 4:1, from full rated output to-30dB, Signal-to Noise Ratio: >75dB, Crosstalk: >80dB (below rated power, 20Hz to 1kHz), toroidal transformer, 1.4’’ TS Jack , RCA, etc complete as required. |
| 22 | Supplying, Installation, testing & commissioning of High Performance Digital Wireless dual handheld microphone system, 200 selectable frequencies, RF Carrier Frequency Range - CH1: 612.000 - 651.600 MHz (100 Selectable Frequencies) CH2: 652.000 - 691.600 MHz (100 Selectable Frequencies), Audio Frequency Range - 30Hz ~ 20 kHz, Signal-to-noise (A-weighted) - 120dB(A) , RF output - 50 mW max, Oscillation Mode -Inside the chip VCO oscillation True Diversity dual reciever, Two receivers in 1U rack mount frame, Two Dynamic wireless handheld transmitter microphones, Long range low power consumption, etc complete as required. |
| 23 | Supply Installation testing & Commissioning of 4x2 matrix Switcher with Supports resolutions up to 4K 60Hz, with additional support for HDR, Extract audio from HDMI® to Toslink (Optical) and 3.5mm audio, Supports ARC as well as a Downscaler-Function via HDMI® Out B, etc complete as required. |
| 24 | Supply Installation testing & Commissioning of 70m Cat.6 HDMI 4K30 & IR Extender with PoC & Loop Out, Extends HDMI® & IR Signals up to 70m using a single Cat.6 Cable, Supports resolutions up to 3840x2160@30Hz 4:4:4 8bit, etc complete as required. |
| 25 | Supply, Installation, Testing & Commissioning of Pop-up Cable Cubby having 1 no. HDMI, 1 RJ45 and 1 no. power socket etc. as required. |
| 26 | Supply Installation testing & Commissioning of Wireless presentation device along with 1 nos. dongle, Operating system Windows 10 and higher macOS 11 (BigSur) and higher., Android v9 and higher (ClickShare App)*, iOS 12 and higher (ClickShare App)*, Video outputs 4K UHD (3840*2160) @ 30Hz. HDMI 1.4b, Audio output HDMI, USB 1 X USB-A, 1 X USB-C, ClickShare Buttons 0, ClickShare App Desktop & Mobile, Native protocols Airplay, Google Cast, Miracast, Maximum number of simultaneous connections (with Buttons and/or App) 32, Noise Level Max. 25dBA @ 0-30°C, Max. 30dBA @ 30-40°C, Authentication protocol WPA2-PSK in stand alone mode WPA2-PSK or IEEE 802.1X using the ClickShare Button in network integration mode, Wireless transmission protocol IEEE 802.11 a/g/n/ac and IEEE 802.15.1, Reach Adjustable with signal strength modulation; max. 30m (100 ft) between ClickShare Button and ClickShare Base Unit, Frequency band 2.4 GHZ and 5 GHz, Frequency band 2.4 GHZ and 5 GHz (DFS channels supported in select number of countries), Connections 1x Ethernet LAN 1Gbit 1x USB Type-C 2.0 (front); 1x USB Type A 2.0 (front), Temperature range Operating: 0°C to +40°C (+32°F to +104°F), Max: 35°C (95°F) at 3000m, Storage: -20°C to +60°C (-4°F to +140°F), Humidity Storage: 0 to 90% relative humidity, non-condensing, Operation: 0 to 85% relative humidity, non-condensing, etc as required. |
| 27 | Supply, Installation, Testing & Commissioning of HDMI to HDMI cable 20 Mtr etc. as reqd. |
| 28 | Supply, Installation, Testing & Commissioning of HDMI to HDMI cable 1.5 Mtr etc. as reqd. |
| 29 | Supply, Installation, Testing & Commissioning of 18U pre-wired Audio Equipment’s Rack front lockable glass door, fan tray for cooling, caster wheels base, main panel with spike buster, individual fuse power supply unit, including all internal wiring, etc as required. |
| 30 | Supply, Installation, Testing & Commissioning of shieled 2 Mtrs CAT 6, STP cable along with compatible connectors in the existing surface / recessed steel / PVC as required. |
| 31 | Supply, Installation, Testing & Commissioning of shieled 15 Mtrs CAT 6, STP cable along with compatible connectors in the existing surface / recessed steel / PVC as required. |
| 32 | Supply Laying & Fixing of of Microphone lines high grade, professional low-noise, 2 crore high conductivity PVC insulated in PVC jacket, shielded copper cable with Di- electric insulator both end with XLR m/f connector as required. |
| 33 | Supply Laying & Fixing of speaker b lines: 2 core, 1.5 sq mm high defintion speaker cable, PVC insulated in PVC jacket laid in existing conduits as reqd. |
| 34 | Supply, installation, testing and commissioning of Video Conferencing System complete with codec is a modular video conferencing engine built for enterprise-grade large meeting environments, supporting both H.323 and SIP up to 6 Mbps bandwidth with IPv4/IPv6 dual-stack networking. It delivers people video resolutions up to 4K Ultra HD at 30 fps and 1080p at 60 fps, with support for H.264 AVC, High Profile, H.265 (HEVC), SVC, H.263, and RTV video standards. Content sharing is enabled via HDMI input and USB-C, with resolutions supported up to UHD (3840×2160). The codec integrates advanced audio processing, including automatic gain control, adaptive echo cancellation, noise suppression, NoiseBlockAI, Acoustic Fence, keyboard noise reduction, and Active Lip Sync. It supports a wide range of audio codecs, such as Siren 22, G.719, G.722.1 Annex C, G.722, G.711, and G.729A. Connectivity includes 2× HDMI outputs, 1× HDMI input, 1× USB-C, 2× USB-A, 1× line-in and line-out (3.5 mm), 1× RJ-45 for network (PoE+ IEEE 802.3at class 4/5/6), and an auxiliary LLN port for peripherals. The device is managed via the Poly Lens cloud and supports remote APIs (REST/CLI). It operates within 0–40 °C, with dimensions of approximately 248 × 152 × 35 mm and weight around 0.8 kg.The smart PTZ camera integrates seamlessly with the G62 and features a 4K UHD (3840×2160) 8 MP image sensor, 12× optical zoom, and 16× digital zoom. It offers a wide field of view of up to 107° (diagonal), with motorized pan (±170°) and tilt (±30°) functions. Intelligent framing is enabled via Poly DirectorAI, supporting Presenter Tracking and Group Framing for automated meeting experiences. The camera provides flexible connectivity through USB-B and Ethernet (PoE+ 802.3at), with optional 12 VDC input. A dual-microphone beamforming array is integrated for localized audio pickup. Physical specifications include dimensions of approximately 200 × 150 × 165 mm and a weight of 1.79 kg. The camera includes wall mount accessories and remote control, and it is certified for Microsoft Teams and Zoom Rooms.The Touch controller complements the system with a 10-inch high-resolution interactive display for meeting scheduling, room control, and call management. It includes multi-colored LED indicators for room status and a simplified single-cable installation for both power and data over Ethernet (PoE). The TC10 integrates with the Poly ecosystem and can be centrally managed through Poly Lens, enabling IT administrators to monitor, configure, and update devices remotely. Together, the Poly Studio G62 codec, Poly Studio E60 camera, and Poly TC10 controller deliver a complete modular video conferencing solution, providing 4K video, enterprise-grade audio, AI-powered intelligent camera tracking, and intuitive room control, making it suitable for medium-to-large conference rooms requiring reliable, scalable, and future-proof collaboration infrastructure etc. as required. |
| 35 | Supply, installation, testing and commissioning of 8 analog input 8 analog output Digital Signal Processor, Complete matrix routing of all inputs and outputs, High-performance ADSP SHARC 21489 40-bit floating-point processor optimised for audio processing, 24bit/48kHz sampling rate for exceptional audio quality and performance, Frequency Response 20Hz – 20kHz, ±0.3dB, THD + Noise < -94dB @17dBu, Comprehensive metering with 16 user presets, Input channels: Signal generator (sine wave, White noise and Pink noise), expander, compressor, AGC, PEQ, feedback suppression and 48V phantom power, Automixer with gain sharing and mic priority setting, Acoustic Echo Cancellation (AEC) 8×8 for local and remote inputs, Output channels: Low pass & high pass filters – Bessel, Butterworth, Linkwitz-Riley slopes from 6-48dB/oct, 8 Parametric equalizer (PEQ) – PEQ, low shelf, high shelf, low pass, high pass, Delay (up-to 408m/1200ms) and limiter on output channels, In-built USB sound card for USB recording, playback and soft video conferencing codec, 8-way GPIO (General purpose input output) configured as inputs or outputs, allowing for flexible control of digital signals, Camera tracking with look at me feature via voice control, Ethernet, RS232/485 control interface for third-party control, Full feature control software, etc complete as required. Please Enable Macros to View BoQ information |
