|
| 1 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area n. exc 1.5 Sqm each, complete all as specified and as directed. |
| 2 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed. |
| 3 | Taking down chowkhat or frames of area n. exc 1.5 Sqm each, complete all as specified and as directed. |
| 4 | Taking down chowkhat or frames of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed. |
| 5 | Taking down shutters of any description of area n exc 1sqm each, complete all as specified and as directed. |
| 6 | Taking down shutters of any description of area exc 1sqm but not exc 2sqm each, complete all as specified and as directed. |
| 7 | M&L for Second class hard wood plain solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints , complete all as specified and as directed |
| 8 | M&L for PCC 1:4:8 type D2 (using 40mm graded Granite stone aggregate) as in foundation, sub base of flooring, filling mass concrete etc., with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 9 | M&L for PCC type B2 [1:2:4] using 40mm graded granite stone aggregate) as in surface channel, drain and the like including weathering, slightly rounded or chamfered angles and throating, finished plain fair faces, including demolition of existing cement concrete of any description, complete all as specified and as directed. |
| 10 | M&L for PCC 1:3:6 type C2 (using 40mm graded Granite stone aggregate) as in foundation, sub base of flooring, filling mass concrete etc., with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 11 | M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed. |
| 12 | M&L for 100mm thick plain cement concrete 1:4:8 type D2 (using 40mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 13 | M&L for 50mm thick plain cement concrete 1:2:4 type B2 (using 40mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 14 | M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 mtres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 15 | S&F Pre painted galvalume coating GI based corrugated / trapezoidal / tiles profile steel sheet, AZ-70 coating mass, 0.50mm thick (TCT) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washers, with and including dismantling plain or corrugated steel sheeting, any gauge, thickness in roof coverings, complete all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps etc. |
| 16 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, with and including dismantling plain or corrugated steel sheeting, any gauge, thickness in roof coverings, complete all as specified and as directed. |
| 17 | M&L for Manglore Pattern roofing tiles, fixed as in roofing, interlocking at side joints, laid dry, with and including dismantling u/s mangalore pattren roof tiles, removing rubbish off the premises, complete all as specified and as directed. |
| 18 | M&L for Cement concrete roofing tiles, rustic red colour, 420 x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry, with and including dismantling u/s mangalore pattren roof tiles, removing rubbish off the premises, complete all as specified and as directed. |
| 19 | M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, with and including dismantling u/s mangalore pattren ridge cap roof tiles, removing rubbish off the premises, complete all as specified and as directed. |
| 20 | S&F IN REPAIR 2mm thick Fibre glass reinforced translucent corrugated sheet, with two corrugations side lap as in roofs, fixed with J or L type hooks or coach screw & washer or cranked hook bolts as per site requirement, with and including dismantling existing u/s roof sheeting of any size as in roof coverings, complete all as specified and as directed. |
| 21 | S&F Aluminium Composite Pannel board of 4mm thick, comprising of a core containing not less than 70% non combustible mineral filling, sandwiched between two skins of 0.50mm thick aluminium alloy PERALUMAN-100 of weight not less than 7.6kg/Sqm, with all sub structures, anchors, hardware and all fittings, fixed over and including aluminium section of size 35x25x2mm and 1.0m x 0.30m panel with and including necessary frame work, screwing & scaffolding, fixed with screws / nails, with and including dismantling existing u/s boarding of any description, complete all as specified. |
| 22 | S&F PVC (SWR) eaves gutter 150mm dia trapezodial shape Gde-I fixed with MS clamps, including taking down existing u/s eaves gutter pipes, rain water pipes (of any size or pattern) including fittings, head shoes, bends, swan neck etc., complete all as specified and as directed. |
| 23 | S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle channel or flat sections including distance pieces, cleats etc. conforming to grade Fe 410-W Gde E - 250 quality 'B', with and including dismantling wrought iron or mild steel of any description, complete all as specified and as directed. |
| 24 | M&L for 2nd class hard-wood boarding 15mm thick, as in floor / skirting, planed one side, with butt joint and fixed with nails, with and including applying two coats of varnishing over a coat of staining oil with preparation of new wood surfaces, with and including dismantling old boarding of any type, complete all as specified and as directed. |
| 25 | M&L for False ceiling with High Pressure Steam Cured (HPSC) 4mm thick Non Asbestos Fibre Cement ceiling boards fixed with and including powder coated aluminium snap grid of size 605mmx605mm consisting of 25X25X1.25mm aluminium angles and TEEs of size 35x25x1.25mm with GI wire of required length and 6mm dia hanger grid suspended from trusses/ ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying three coats of white wash on ceiling surface, with and including taking down existing u/s ceiling with frame work of any description, complete all as specified and as directed. |
| 26 | M&L for False ceiling with 10mm thick plaster of Paris (gypsum anhydrous) decorative ceiling at any height, reinforced with GI wire mesh, fixed with and including powder coated aluminium concealed snap grid of size 605mmx605mm consisting of 25X25X1.25mm aluminium angles and TEEs of size 35x25x1.25mm with GI wire of required length and 6mm dia hanger grid suspended from trusses/ ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying two coats of distemper oil emulsion over a coat of primer & cement based wall care putty on ceiling surface, with and including taking down existing u/s ceiling with frame work of any description, complete all as specified and as directed. |
| 27 | M&L for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube of top and bottom rails, MS frame shall be covered with heat moulded prelaminated PVC \\"C\\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheet for top rail ,lock rail and bottom rail on either side and as gap insert for top and bottom rail. Pannelling of prelaminated PVC sheet to be fitted in MS frame welded /sealed to the stiles and rails with suitable PVC sheet bedding and jointed together with solvent cement as per specification and drawings, complete all as specified and as directed. |
| 28 | M&L for solid PVC Door Frame of Size 50mm x 47mm out of 5mm prelaminated PVC sheet on both sides reinforced with M.S Square tube, supplying and fixing in opening as per sepcification and drawing, complete all as specified and as directed. |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window Frame/ Chowkhat of size 65mm x 125mm with virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibbers (wood powder/ rice husk/ wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) with mitre joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant, and fixed in position with and including MS hold fast/lugs/SS dash fasteners as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 30 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension rade), calcium carbonate and natural fibbers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, complete all as directed by Engineer-in-Charge. |
| 31 | M&L for Factory made 2nd class hard wood Glazed and skeleton shutters , 35mm thick, open rebated and prepared to receive glass, gauze, etc. (with divided in to square with plain, chamfered or rounded, mitered and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats, complete all as specified and as directed. |
| 32 | S&F IN REPAIR Collapsible steel gates, top hung, consisting of channel pickets, pivoted, flat bars, top and bottom runners, brass, handles etc., as specified, erected in position and securing runners with holdfasts and brackets, including taking down existing u/s steel gate of any size & description, complete all as specified and as directed. |
| 33 | Repairs to loose hanging mild steel window / ventilator shutters of area not exc 1.0SqM upto 3 story height buildings, by repair to hardware by welding / screws, making smooth function of shutters by making necessary repair and making good the disturbed surface, complete all as specified and as directed. |
| 34 | S&F IN REAPIR Helical door spring MS 300mm long ordinary rat tail pattern spring, ISI marked, including roller and roller plate complete fixed to wooden/steel chowkats complete all as specified and as directed. |
| 35 | S&F MS butt hinges cold rolled medium weight 100mm size, ISI marked, complete all as specified and as directed. |
| 36 | S&F IN REPAIR Aluminium anodised barrel tower bolt of extruded section of size 200mm long complete, complete all as specified and as directed. |
| 37 | S&F IN REPAIR Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed. |
| 38 | S&F IN REPAIR 150mm long extruded section aluminium alloy anodised handles fabricated type, complete all as specified and as directed. |
| 39 | M&L for Machine cut Kota stone slab 18-20mm thick, as in flooring over with and including 20mm thick cement screed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match shade of the slab, including cutting, waste, grinding, rubbing and polishing, with and including demolition of existing floor, complete all as specified. |
| 40 | S&F Machine cut kota stone slab 18-20mm thick, as in vertical surfaces such as skirting/dado, laid over and including 15mm thick backing coat in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, with and including demolition of existing skirting/dado, complete all as specifed and as directed. |
| 41 | S&F IN REPAIR Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed. |
| 42 | M&L for Floor door stopper of Aluminium alloy body & tongue, anodised with 150mm long and hard drawn steel spring, fixed in door, complete all as specified and as directed. |
| 43 | S&F IN REPAIR Aluminium (Die cast body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified. |
| 44 | S&F IN REPAIR SS curtain rod 20mm bore dia with brackets, fixing stops, roller bracket, wooden nobs etc., with Harrison rails, complete all as specified. |
| 45 | M&L for 4 mm thick sheet glass ordinary quality and glazing with oil putty in squares exc 0.5 Sqm in each pane, complete all as specified and as directed. |
| 46 | M&L for 12mm thick sheet glass, toughened glass as in hinged doors, partitions, automatic door closer, including cutting to required shape, drilling holes etc., as required, with and including hacking out old broken glass of any type & position, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 47 | M&L for 12mm thick sheet glass, toughened glass as in hinged doors, partitions, automatic door closer, including cutting to required shape, drilling holes etc., as required, with and including hacking out old broken glass of any type & position, complete all as specified and as directed. Please Enable Macros to View BoQ information |
