|
| 1 | CIVILPORTION OF WORK:-Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S. gates, garage door, collapsible gates with top and bottom rails, steel windows, critical frames for windows, stair case and parapet railing made out of M.S Square bar/ flat including stair case hand railing with 40mm. dia G.I.pipe etc. including painting two coats over a coat of redoxide primer as per approved drawing and design with cost of all materials & labour, taxes, labour cess, T&P, sundries etc. complete in all respect as per specification & direction of the Engineer-in-Charge.(i) Ground Floor |
| 2 | Finishing surface of walls with cement based wall putty (water based) of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging charges with cost of all materials labour T & P etc. as per direction of Engineer -In -charge.(i) Ground Floor |
| 3 | Painting two coats with plastic emulsion paint to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, taxes of all materials, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge.(i) Ground Floor |
| 4 | Painting two coats with approved enamel paints of wood / steel work including sand papering, polishing the surface, cost, conveyances of all materials and cost of all labour etc, complete as per specification & direction of E.I.C.(i) Ground Floor |
| 5 | Cement Concrete (1:2:4) using 12mm size hard granite C.B. chips approved quality from approved quarry including cost, carriage, royalty, cost of all labour. etc complete and as directed by E.I.C.(i) Ground Floor |
| 6 | Painting two coats with approved weather seal over a coat of Water bound Wall cement primer to outside surface of wall in Ground floor including sand papering, polishing the surface, cost, conveyances, taxes of all materials and cost of all labour,labour cess with T&P etc, complete as per specification & direction of Engineer-in-charge.(i) Ground Floor |
| 7 | GPH PORTION OF WORK:- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.(A) 20mm dia C - PVC pipe |
| 8 | (B) 25mm dia C - PVC pipe |
| 9 | Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials including cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.(i) 15mm dia CP angle stop cock (Con - CHR - 053KN Jaquar make) |
| 10 | (ii) Elbow |
| 11 | (iii) 15mm dia CP two in one bib cock (Con - CHR - 041KN Jaquar make) |
| 12 | (iv) 15mm dia CP Bib cock (Jaquar-Medi series) FLR-CHR - 5043N |
| 13 | (v) 15mm dia CP Long Body Bib cock (Con - CHR - 107KN Jaquar make) |
| 14 | (vi) 20mm dia CP consealed stop cock (Con - CHR - 083KN Jaquar make) |
| 15 | (vii) 15mm dia CP Health faucet (Con - ALD - MCH - 573 Jaquar make) |
| 16 | (viii) 25mm dia brass full way valve (Shakti make) |
| 17 | (ix) 32mm dia brass full way valve (Shakti make) |
| 18 | (x) 15mm CP Extension piece |
| 19 | (xi) 125mm CP grating |
| 20 | (xii) 15mm size C.P. flange |
| 21 | Supplying all materials , labour, T&P and fixing rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS:12701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 5.40 mtr. lengthx0.25 mtr width KB brickwork in cement mortar (1:6) of 0.46m height in staging and 0.13mtr thick circular protection wall of 0.46mtr height to support the tank,12mm thick cement plaster in cement mortar (1:6) over brick work, RCC slab of size 1.60mX1.60m and 0.10m thick ,RCC beam of 0.25mx0.30m and 3.40m average length in cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips and required steel reinforcement including centering and shuttering,watering,curing ,cost of all materials,conveyance of all materials to worksite , payment of royalty, all taxes etc.all complete as per approved drawing , P.H. specification and direction of Engineer-in-charge.(i) 2000 liters capacity PVC water storage tank |
| 22 | Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.(i) 110mm U-PVC SWR Pipe (Supreme/ahirvad) |
| 23 | 110mm U-PVC ‘P’ Trap (Ori Plast / Finolex / Supreme Make) |
| 24 | 110mm U-PVC door bend (Ori Plast / Finolex / Supreme Make) |
| 25 | 110mm U-PVC Plain bend (Ori Plast / Finolex / Supreme Make) |
| 26 | 110mm U-PVC offset without ear (Ori Plast / Finolex / Supreme Make) |
| 27 | 110mm U-PVC Cowl (Ori Plast / Finolex / Supreme Make) |
| 28 | 110mm U-PVC Socket (Ori Plast / Finolex / Supreme Make) |
| 29 | Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x 30mm footrest, fixing 100mm dia HCI P or S trap (with/without 50mm dia horn) for water colset squatting pan including jointing the trap with pan in cement mortar (1:1) cutting the floor and mending good the damages , cost & conveyance of all materials to worksite, payment of royality , taxes etc.all complete as per P.H specification and direction of the Engineer-in-charge.(i) 580mm size Orissa pan (Hindware / Parryware / Neycer make) |
| 30 | Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet (European type W.C. pan)with integral P or S trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing , cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.(i) European water closet with P trap plain (Hindware / Parryware / Neycer make) |
| 31 | Supplying all materials, labour T&P and and fixing 12.50 liters/10 liters capacity low level flushing cistern with a pair of cast iron or M.S. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle,unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connceting the inlet pipe with suupply main , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.(i) 10 ltr. Capacity pvc L.L. cistern with 32mm. Dia CP long flush bend (Slimline - white - Parryware make) |
| 32 | Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, cost & conveyance of all materials to worksite, payment of taxes etc.all complete as perP.H specification and direction of the Engineer-in-charge.(i) 550mm x 400mm W.H.basin (Hindware / Parryware / Neycer make) with 15mm dia C.P.pillar cock (Plaza make) with pedestal |
| 33 | Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge.(i) 25mm x 600mm long CP towel rail |
| 34 | (ii) Towel ring |
| 35 | Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rail complete fixed to wooden plugs with CP screws as per specification and direction of Engineer in charge.(i) 600mm x 125mm plate glass shelf with CP/NP guard rails |
| 36 | Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of Engineer in charge.(i) 600mm x 450mm size B.E mirror (swivelled type) |
| 37 | Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge.(i) CP soap holder |
| 38 | Supplying all materials, labour, T&P for fitting & fixing plain edge kitchen/wall sink of all standard sizes with a pair of bracket, C.P. waste, trap & P.V.C. waste pipe & painting brackets including supply of cement concrete & mortar etc. all complete. 24” x 18” x 10” sink |
| 39 | Providing fitting, fixing of Aluminium door with anodized AL. door section of 9202 as vertical member,9201 as top and 9200 as middle bottom member with frame section No. 9221 and tapered clip no. 4660 and the frame to be completed by means of jointing angle No. 1855 Including all Cost of Labour. T&P hire charges of drilling machine. labour charges etc. complete. Ref : OBI10 |
| 40 | Supplying all materials labour T&P and constructing 1.40m dia x 2.00 m deep soak way pit with dry brick having crossing strength not less than 75Kg/CM2 to 99Kg/CM2 in CM(1:6) for the remaining 0.4572mm height of wall at top CC(1:3)inside and outside inside fill with dry brick khoa size 38mm ,CM thick RCC perforated slab to a height of 1.9012m from bottom covered by means of 50mmthick RCC wall cover in pieces filled with iron plugs including earth work in excavation refilling of cavity around the pit and painting the iron works complete as per PHD design and specification including carriage of all materials to site. |
| 41 | Supplying all materials ,labour ,T&P and constructing Inspection Chamber of inside size 760mm x 760mm x 460mm with cement concrete (1:3:6) using 40mm size crusher broken hard black granite metal on bed , KB brick work in cement mortar (1:6) in foundation and plinth, moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips, 12mm thick cement plaster (1:3) with cement punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size crusher broken hard black granite chips with R.C.C man hole cover, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering,curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc.all complete as per approved drawing, P.H specification and direction of Engineer-in-charge.(i) Inside size 76cm x 76cm x 46cm with 18” dia RCC MH cover |
| 42 | Supplying all materials, labour, T&P and providing, fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1 phase line voltage ranging from 320 volt to 450 volt conforming to IS: 8034/89 with following specifications with suitable control panel, jointing with GI / PVC / HDPE pipes, electrification, testing, commissioning, trial running, conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge (Texmo / Crompton Greaves / Kirloskar make).(i) 1 H.P. Single phase/ three phase 3 stage head renge of 20 to 35 mtr with discharge capasity 145 to 110 L.P.M With outlet dia 25 mm |
| 43 | (ii) DOL Control panel |
| 44 | (iii) 40mm dia steel short piece |
| 45 | (iv) Well cap |
| 46 | (v) 50mm size CI bracket |
| 47 | (vi) 2.50sqmm flat cable |
| 48 | (vii) 20mm dia rigid UPVC pipes |
| 49 | (viii) Steel rope with cover |
| 50 | (ix) Labour charges for lowering including transportation |
| 51 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor HDPE pipes and pipe fittings conforming to IS: 4984/2000 (10kgf / sqcm) of the following nominal bore with clamps and jointing by Fusion welding method including testing, making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge.(i) 32mm HDPE pipes (Finolex / Supreme make) |
| 52 | EI PORTION OF WORK:-Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLSH/LSZH PVC insulated copper conductor of ISI marked Make- Finolex / Anchor / Polycab / HAVELLS / RR KABLE / KEI or equievalant reputed make A catagory ISI marked as approved with 20 mm dia PVC flexible non metallic conduit FRLS type ISI marked. Make-AKG / Anchor / Havells or equievalant reputed make A catagory ISI marked as approved 6A modular type (anti bactorial & flame retradant type) switch ISI marked and ceiling rose ISI marked Make - Anchor / Havells of modular type G.I box with metallic cover plate (both side) of suitable size, modular box with 1.5 sq.mm FRLSH PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge.(a) GROUP-A |
| 53 | (b) GROUP-B |
| 54 | (c) GROUP-C |
| 55 | Supplying, fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type) ((anti bactorial & flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in - Charge. Make - Schneider (Zencelo) / legrand (Arteor) / Panasonic (vision) or equievalant reputed make & model A catagory ISI marked as approved, complete suitable. (Maximum 02 nos point in one circuit). |
| 56 | Supplying, fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket (modular type) ((anti bactorial & flame retradant type)) with suitable size modular box & cover (anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider (Zencelo) / legrand (Arteor) / Panasonic (vision) or equievalant make & model ISI marked as approved, complete suitable for IPH standard hospital. (Maximum 02 nos point in one circuit). |
| 57 | Supplying, fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket (modular type) ((anti bactorial & flame retradant type)) with suitable size modular box & cover(anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge. Make - Schneider (Zencelo) / legrand (Arteor) / Panasonic (vision) or equievalant reputed make A catagory ISI marked as approved, (For equipement power) |
| 58 | Supplying, fixing of 2 x 6A+1X1 6A Plug on the Computer board with complete fitting by 01 no of 16A+2 no 6A switch & socket (modular type) ((anti bactorial & falme retradant type) with suitable size modular box & metallic cover plate (both side) (anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of Engg-in-charge.Make-Schneider (Zencelo) / legrand (Arteor) / Panasonic (vision) or equievalant reputed make & model A catagory ISI marked as approved, (For equipement power |
| 59 | Receass wiring for circuit / submain wiring with the following mentioned size PVC FRLSH/LSZH insulated, copper conductor, single core cable (Finolex / Anchor / Polycab / HAVELLS / RR KEBLE) or equievalant reputed make A catagory ISI marked as approved, in recessed PVC conduit Heavy duty FRLS of mentioned size (AKG / Anchor / Kinjal or equievalant ISI marked as approved) as required as per direction of Engg.-in-Charge. (i) 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty flexible conduit (LDB to LSB / LIGHT CKT) (2X1.5+1X1.5) |
| 60 | (ii) 2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty flexible conduit.(BDB to LSB / LIGHT CKT / 5A PLUG / INVERTER POINT TO EACH QTR) (2X2.5+1X1.5) |
| 61 | (iii) 2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty flexible conduit. (PDB to PSB / GAYSER POINT / AC POINT / ROOM LIGHT CONTROL TO CORRIDOOR POINT / DG PANEL ESSENTIAL LOAD) (2X4+1X1.5) |
| 62 | (iv) 2 nos single core 6 sq. mm copper wire for phase and neutral and 01 no of single core 2.5 sq. mm copper wire for earth continuty conductor in 25 mm dia non metallic heavy duty flexible conduit .(LFDB TO LBDB) (2X6+1X2.5) |
| 63 | Supply and fixing CALL bell (Ding dong type) / Buzzer on the existing switch box/cover. Equievalant higher model of Schneider / Hager / Siemens / Anchor / Panasonic make or equievalant reputed make & model A catagory ISI marked as approved .as required as per direction of Engg.-in-Charge. |
| 64 | S/F of Bakelite angle holder/batten holder (make-Anchor / Havells / Panasonic or equievalant reputed make A catagory ISI marked as approved) of ISI marked conforming to IS-1258/1987 in place of ceiling rose as per direction of Engg.-in-Charge. |
| 65 | Supplying,fixing of Blanking plate (modular type) ((anti bactorial & flame retradant type)) in existing switch box(anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of Engg-in-charge. Make-Schneider (Zencelo) / legrand (Arteor) / Panasonic (vision). |
| 66 | Supplying, installation, of exhaust fan of heavy duty 300 mm sweep (Make - Equievalant higher model with 5 star rated of Bajaj / Havells / almonard / Anchor / Panasonic / Usha or equievalant reputed make & model A catagory ISI marked as approved) of exhaust fan in the existing wall, including fixing & conntection as required as per direction of Engg.-in-Charge. |
| 67 | Supplying, installation, testing and commssioning of 1200 mm sweep white / milky colour BLDC ceiling fan with aluminium blades having wattage not more than 28W and air delivery ≥ 215m3 / min Make-Crompton Energion Groove / Havells Efficiencia Neo / Usha Technix) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge, Replacement Warranty will be 4 years. |
| 68 | Supplying and fixing of Modular step type regulator of approved ISI Make |
| 69 | SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Similar to Panasonic Model No. PBTM08208 or similar model of Bajaj / PHILIPS / LT/ wipro or equievalant reputed make & model A catagory ISI marked as approved.). |
| 70 | SITC of Sleek LED 12 watt mirror light fitting with extruded polycarbonate housing, High optically efficient diffuser, above wash basin complete with all accessories etc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge.( Make : WIPRO Model No: LL20 - 111 - XXX - 60 - NE or similar model of Bajaj / PHILIPS / Panasonic or equievalant reputed make & model A catagory ISI marked as approved. |
| 71 | BDBS, DB, AC DB, FLOOR PANELS, MCBSSupplying and fixing of following mentioned way, three pole / single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3, integrated door earthing system offering additional safety to the user, High quality polyurethane Gasket, the box and cover shall be fabricated to withstand IK09, the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface / recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make - LEGRAND - Ekino x 3 DB / Siemens - Betaguard / Schneider- Acti 9 / Panasonic (Equivalant model) / ABB (Equivalant model) or equievalant reputed make & model A catagory ISI marked as approved as per direction of Engg.-in-Charge.(i) Supply and fixing of 12 way DD single pole and neutral sheet steel MCB distribution board 250V on surface / recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB / RCCB / Isolator) (ALL LIGHT WITH CORRIDOOR / COMMON AREA, EM LIGHT, UPS LOAD, EM LOAD LIGHT LOAD, POWER LOAD) |
| 72 | (ii) Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series, single poles MCB of Make - LEGRAND - Ekinox3 DB / Siemens-Betaguard / Schneider - Acti 9 / L&T (Equievalant model) / Panasonic (Equivalant model) / ABB (Equivalant model) or equievalant reputed make & model A catagory ISI marked as approved. The existing MCB DB complete with connections as per direction of Engg.-in-Charge. |
| 73 | S/F of 63 Amp DP Main switch ISI Marked (Anchor / Cona) |
| 74 | SITC of Sleek LED 10 watt BH fitting with extruded polycarbonate housing, High optically efficient diffuser, above wash basin complete with all accessories etc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge.(Make : WIPRO Model No: LL20 - 111 - XXX - 60 - NE or similar model of Bajaj / PHILIPS / Panasonic or equievalant reputed make & model A catagory ISI marked as approved. |
| 75 | S/F of Standard earthing with GI Earth pipe 3 mtr long 40 mm dia ISI Marked including accessories as per Govt. Specification. |
| 76 | S/F of 8 SWG copper wire for earthing |
| 77 | S/F of 1X 1.5 sq.mm Cu. Wire for Inverter wiring |
| 78 | Supplying & laying of 10 mm2 Service Cable of any appproved ISI Make |
| 79 | Supply & Fixing of LED Street Light of 50 watt on Roof Parapet with arm & clamping accessories Please Enable Macros to View BoQ information |
