|
| 1 | CIVIL WORKDismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 2 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 3 | Providing designation 75 A brick work in C.M. (1: 3) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 4 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 5 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. sqm 516.60 |
| 6 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size:600 x 600 mm sqm |
| 7 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. |
| 8 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 9 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 11 | Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I. |
| 12 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 13 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded Code Description Unit Rate No. star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be |
| 14 | Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 15 | Refixing old glass panes with putty and nails |
| 16 | Providing two coats of synthetic enamel paint of approved shade and make over old wooden surface including cleaning the surface after removing dirt including scales, smokes, grease and sand preparing, including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 17 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron |
| 18 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)) |
| 19 | Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineerin-charge.(Payment of providing and fixing auto closing hinges shall be paid separately) |
| 20 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) |
| 21 | Cairrage of Materials (a) sand with lead 13km |
| 22 | (b)s/c with lead 8km |
| 23 | ( c) Bricks lead 25km |
| 24 | SANITARY WORKProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including testing of joints complete as per direction of Engineer in Charge.Concealed work,including cutting chases and making good the walls etc15 mm nominal |
| 25 | 20 mm nominal |
| 26 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints completeas per direction of Engineer in Charge.25mm nominal |
| 27 | 50mm nominal |
| 28 | Making holes in walls for laying G.I. pipes and restoring the same after pipe laying with complete job250 mm thick wall |
| 29 | Providing and fixing Gun metal full way valve of approved quality with complete job-25 mm dia |
| 30 | Providing and fixing male ended 15mm dia brass bib cock with complete job |
| 31 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hol Pillor Cockr of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole Pillor Cock : Counter Basin |
| 32 | Providing and fixing PVC pipes of following size do ----do all com job.75mm |
| 33 | 110mm |
| 34 | Providing and fixing PVC pipes fittings of following size do ----do all com job. Bend75mm |
| 35 | 110mm |
| 36 | coupler110mm |
| 37 | Providing and fixing PTMT grating of approved quality and colour |
| 38 | Providing and fixing 100 mm sand cast Iron grating for gully trap. each |
| 39 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design |
| 40 | 17.34 Providing and fixing toilet paper holder :C.P. brass each |
| 41 | supplying material labour for construction of inspection chamber do-----do all comp job. |
| 42 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other with complete job 580 mm long with 12.50 liter low level PVC Cistern |
| 43 | Supplying fitting and fixing the following items complete with all with complete jobSoap Dish |
| 44 | Mirror (450 x 300 mm) |
| 45 | Towel ring |
| 46 | Suppling, fitting and fixiilS40mm high-vitreous white glaz-dd earthen E.W.C. with 'p' trap of parry hindustan or any other approved l.S.S. make including supplying and fixing l5litres C.l. mosquito proof low down flushing cistern of approved make with complote fittings with C.l.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of appro- ved quality weight not less than 450grams 1Smm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other LS.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and dlrection of E/|. |
| 47 | Supplying, fitting and fixlng flat back or angular, lipped front vitreous white glazed earthen ware urinal of 'Hindustan 'Parry\\" or any other approved l.S.S make wifi 5 liters capacity C.l. automatic fulsing cistern of reliance for any other l.S.S. approved make with all fittings with C,l.or R.S. brackets, standard size G.l. flush pipe with fitting clamps.lSmm C.1. bodv brase splndle stoo cock of aoDroved oualitv ding painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. a) Flat back or standing corner (600mmx350mm) |
| 48 | ELECTRICAL WORKWiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, with modular switch, modular plate suitable GI box etc as required |
| 49 | Power plug wiring in PVC conduit (2 x 4 sq.mm) - Wiring for light/power plug with 2 x 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 50 | Circuit/submain wiring in PVC conduit - Wiring for Circuit/submain wiring along with earth wire the following sizes PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.2x1.5 Sqmm + 1x1.5 sqmm earth wire (For 5/6A Plug Points) |
| 51 | 2x2.5 Sqmm + 1x2.5 sq mm earth wire |
| 52 | 2x4 Sqmm + 1x4 sq mm earth wire |
| 53 | Supplying and fixing of following modular switch / soket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps, one way switch |
| 54 | 3 pin 5/6 amps, socket outlet |
| 55 | 15/ 16 amps, one way switch |
| 56 | 15/16 amps, 6 pin socket outlet |
| 57 | Electronic step fan regulator, deluxe |
| 58 | S/F light plug point with piano type accessories :-Supplying and fixing suitable size GI/PVC box of 75 mm x 75 mm x 50 mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch. connection, painting etc. as required (For light plugs to be used in non residential buildings ) |
| 59 | S/F power plug point with piano type accessories :-Supplying and fixing suitable size GI/PVC box of 121 mm x 173mm x 48mm/(6\\" x 8\\") (nominal size ) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch. connection, painting etc. as required |
| 60 | S/F ceiling rose - Supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/wooden block including connection etc. as required. |
| 61 | S/F Batten holder - Supplying and fixing batten/angle holder including connection etc. as required. |
| 62 | ITC exhaust fan upto 450mm sweeo - Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing commissioning etc. as required. |
| 63 | S/F rewireable double pole/ TP&N switch disconnector :-Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses, including drilling holes in metal board . making connections. etc. as required. |
| 64 | 16 amps, double pole |
| 65 | S/F S.P. MCB DB :-Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way,Single door |
| 66 | S/F 'C' series, MCB - Supplying and fixing following 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connection, testing and commossioning etc. as required. 6/32 amps, Single Pole |
| 67 | S/F DP MCB isolator :-Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 68 | Earthing with G.I. earth pipe 4.5 mtr. Long, 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required |
| 69 | Earthing with copper earth plate 600mmx 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (But without charcoal or coke and salt) |
| 70 | Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth, including soldering etc. as required |
| 71 | P/F G.I. lightning conductor final - Providing and fixing of lightning conductor final, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required. |
| 72 | Reverting, sweating and soldering lightning conductor tape - Reverting, sweating and soldering of copper/G.I. tape (with another copper/G.I. base of the final or any other metalic object) as required. |
| 73 | P/F G.I. lightning conductor tape in horizontal run - Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run) |
| 74 | P/F G.I. lightning conductor tape in vertical run - Provding and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run) |
| 75 | S.I.T.C. of following rating, surface mounted LED light fitting, suitable for 230V 50Hz, single phase supply etc. complete as required.20/22W LED Tube Light |
| 76 | 12\\" (300mm) metal exhaust fan |
| 77 | Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200mm (48\\") BLDC 5star rating 32W Ceiling Fan |
| 78 | Supply of 16\\" (400mm) Wall mounted fan\\" |
| 79 | S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722 with all neccssary accessories as required 2' x 2' LED Panel light |
| 80 | 12W LED Square Down light |
| 81 | N/SMODULAR OT\\"Wall Panels PPGIStandard wall partitions in the Operation Theatre are a composite construction of two skins of PPGI/PPGI with a panel thickness of 50 mm, over a GI framework with a sealed and insulated interior. The standard panel has dimensions of 1000mm x 2425mm. Standard panels have an overall thickness of 50 mm. The self-supporting internal walls are constructed with an interior GI framework. Partition-to-partition connections are maintained with precision with GI profiles that create uniform seams. The partition seams are sealed by silicone with a perfectly flush finish. PUF insulation material is sandwiched between two skin layers and sealed from the exterior by a GI framework. The self-supporting wall should be provided in modular units consisting of external skins (exposed to the room) in PPGI, outer (skin not exposed to the room) PPGI, which will be 0.6mm thick, with a protective film to prevent surface damage during shipping and installation.\\"The movable wall includes the following:a) PUF insulation - 40 Kg/Cum (High pressure)b) GI profile (JSW Steel / Tata Steel / Everest Industries Limited)c) Silicone sealant (clear, white)d) Sheet thickness 0.6 for PPGI |
| 82 | Ceiling panels PPGICeiling panels are designed to fit within each other and suspended by threaded tension bars with adjustable turnbuckles fastened to the overhead support at fixed intervals, Standard Ceiling Panels are 50 mm thick, walkable type, and have a composite construction of two skins of PPGI/PPGI, over a GI framework with a sealed and insulated interior. The ceiling includes the following:\\"a) PUF insulation - 40 Kg/Cum (High Pressure)b) GI. (JSW Steel / Tata Steel / Everest Industries Limited)c) Silicone sealant (clear & white). |
| 83 | Floor:Supply & installation, fixing of seamless static conductive floor, as in OT shall be 2mm thick with covings, with welded joints with following specifications :-(i) Flooring in each operation rooms seamless with perfectly curved flash-covings.(ii) It shall have anti-bacterial and fungicidal properties.(iii) Flooring is a static-conductive, flexible homogeneous vinyl floor. |
| 84 | \\"Hermatically Sealed Automatic Sliding door:Hermatically Automatic in ICU/OT with size1500 mm*2100mm for fixing on wall with following specifications:\\"(a ) Door Blade- Door core of 50-60mm thick built up with HPL sheet as skin at both sides of the door to provide better strength CFC-free, high density polyurethane puff (density 40 kg/m^3), thickness.(b ) Door Profile- Door core is surronded by 2.5mm thick high grade aluminium extrusion profiles with natural anodizing of 15 microns finish. The aero dynamic design of profiles shall make the door ROBUST in its segment league.(c) Gaskets- Door blade is made with 3-tier specially designed 3 side heavy duty replaceable EPDM gasket against wall frame. Bottom sealing with 2-tier heavy duty EPDM gasket to flush with finished floor.(d) Window - High quality double glazed flush vision window of 300mmx300mm view size both sides flush with the door blade.(e) Wall Frame - High grade Al extrusion with natural anodized 15 micron finish wall frame profile. This wall frame profile is 3 sided blind fixed with clading on wall cut out section fron inside & outside of the room.(f) Operation- Door opening/Closing options Automatic |
| 85 | \\"Laminar Airflow System :-Supply,Installation & commissioning of Laminar Airflow System :- Specialised Air Distribution based on Total Presuure Displacement so as to ensure Uniform air quality & quantity along the complete LAF area. Minimum total air changes should be more than 30 per hour. It shall be terminal filter (HEPA filter shall be fitted across total filtration area i.e. 48 sq.ft ), Ultra Clean ventilation system with unidirectional flow. It shall be draft-free, comfortable room climate and minimal, undisruptive noise level. It shall have filtration area of atleast (2440X1830) and capable of filter 4500 cfm of air. It shall have minimal pathogen concentration < 10 c.fu./Cum.\\"(a) Plenum Body - Filter housing and pressure chamber made out of high-end stainless steel 304 medical grade steel with matt polish sheet thickness 1.2mm specially designed to deliver uniform velocity across the entire HEPA plenum to maintain uniform laminarity of air -01 No. Plenum to be fitted with SS grill with perforation.(b ) Fresh air positive pressure consisting of 5 micron washable filter EU4 grade & made of HDPE non woven material. The fresh air component of the air chamge is required to be minimum 12-15 air changes/hour.(c) Mini plate (H 14) HEPA, low pressure drop filter to remove practices sizing upto 0.3 micron with 99.97% particle removing efficiency.(d) Air Handling Unit Capacity 4500cfm(e) The Air Handling unit shall have electrical safety and shall have EN-1886 Certification for mechanical strength. The air handling inits shall be double skin construction, internal coving design and thermal break panels draw-throw type consisting various section, filter section fan section,coil section, mixing box. Flexible canvas connection will be provided between fan outlets and panels, to avoid fan vibration to the body of AHU. Fan motor shall be energy efficient and shall 415 volts, 50 cycles, 3 phase totally enclosed fan cooled class F with IP 55 protection motor, drive to fan shall provided with belt drive arrangements.(e) DX type cooling coils :- The coil has to be designed with interwinding circuits to suit DX system. Coil to be in 2 sets with 6 row in each set.(f) Dampers :- Dampers shall be opposed blade type. Blades shall be made of double skinned aerofoil aluminium section with internal gasket and assembled within a rigid extruded alloy frame. (g) Fine filter and miscellaneous accessories :- Microvee filters 98% efficiency down to 5 micron 610x610x305mm - 2 nos and GI \\"B\\" class drain piping with insulation. Fresh air arrangement with louvers, bird screen & damper(h) Surgeons control panel :- Supply, installation and fixing of surgeon control panel. Membrane type control panel, comprising-Complete with following features :- (i) 1 No. Day Time Clock. (ii) 1 No. Time Lapse Clock..(v) 1 No. AHU, AC , Peripheral light controls. (vi) Lighting control.(i) AHU control panel shall be provided with VFD ( Variable Frequency Drive) IP 20 with provision for Handon/Bypass Mode for appropriate blower fan motor, mains failure relays, electrical distribution equipment and circuit protection equipment for all circuits within the operation theatre . All internal wiring shall terminate in connectors with screw and clamp spring connections of the Clip-on type mounted, on a DIN rail and labelled with indelible proprietary labels. Individual fuses or miniature circuit breakers shall protect all internal circuits.Intergration of AHU with outdoor unit 5.5 Tr each and 5.5 Tr X 1 Set) with proper copper piping, expansion valve, dryerfilte(j) Integration of AHU with Outdoor unit with Expansion valve, dryerfilter, side glass, Proper copper tubing etc.. |
| 86 | Ducting:Ducting is an approach to air management that uses a series of metal or plastic pipes to carry heated or cooled air from one place to another. A duct system is often referred to as ductwork.Duct in Modular Operation Theatre is made by assembling and erection of Aluminium sheet with flange rectangular/square duct made of \\"L\\" shaped hollow profile, duly factory boxes which includes all accessories such as carriage bolt, Gasket & appropriate sealant on longitudinal joints, etc., complete set of 24 gauge. |
| 87 | UV System:4 no's of UVs in risers |
| 88 | Defumigation System:A control panel to be installed outside Ot to monitor OT pressure and to start defumigation system from outside the OT. Defumigatiom system should be such that it Defumigate the Ot in given time and then switch On the AHU to increase OT pressure without operating the Surgeon control panel |
| 89 | X-ray viewing screen:The 2 Film X-ray viewing screen placed behind a transparent screen to view the developed X-rays. (Imported Type) |
| 90 | Magnetic writing board:size of 2 X 3 feet for operating rooms. |
| 91 | \\"Anesthesia Pendant:Single Arm Anesthesia Pendant with 2 Tray and 6 number Gas outlets \\"Carriage Capacity : Max 120 kg. Gas Equipment : Variable According to project.Electrical Equipment : 6 X Electrical Sockets, (optional)Operating Temparature : (+ 10) - (+45) C°Power Supply :220 V 50 HzHorizontal Arm Length : 600 mm to 1000 mm.Packaging Type : Wrapped Package , (wooden packing with extra charge) Product Weight : 120 Kg Product Main Raw Material : Aluminium Extrusion Profile & High impactive ABS with SS304 screwsIV Stand : Two Pole with Hangers.Colour : Single / Dual colour combination or as per requirementAccessories : Gas Outlets, Instrument Basket , Vaccume Carrier, Monitor Stand/ Drawer/Strays. |
| 92 | Pheripheral light:Peripheral light provides overall room illumination and is designed to create a consistent light level across the space, irrespective of any special lighting required in specific locations.A specially designed Peripheral Light for Operation theatre with dimensions of 585 x 585 mm and 36 Watt with LED life of minimum 50,000 Hours and Lumen of 3000 Lux to be installed in the ceiling. |
| 93 | Electric C-Arm Compatible Multipurpose OT Table• Length of Table:1900 m• Width of Table Top: 520 mm• Minimum Height (Without Mattress): Min. 750mm• Maximum Height (Without Mattress): Max. 1000mm• Trendelenburg:25°• Reverse Trendelenburg: 25°• Lateral Tilt: ±20’• Back Section: ±70°• Head Section: ±60°• Leg Section: 0°-90°• Floor Locking System: Center Floor Locking |
| 94 | Orthopedic Attachment• Color: Silver• Finishing: Powder Coated• Material: Stainless Steel• Adjustable & Portable |
| 95 | OT Light - 2 Domes• Intensity: 1,80,000 + 1,80,000 Lux• Shadowless Feature: Yes• Numbers of LEDs: 48 + 48• Intensity Control: 10~100 Digital Capacitive Feather Touch (Fully Remote Controlled)• Fitting Options Available: Ceiling 180 Degrees, Ceiling 360 Degrees, Mobile, Wall Mounted• Spot Diameter: 200-250 mm• Depth of Light Penetration: 150 mm• Color Temperature: 3800 – 4800 K• Color Rendering Index: 95 Ra• Focusing: Adjustable• LED Average life: >50000 Hrs.• Diameter of Light: 700 mm• Power Supply: 220V/50Hz AC• Power Consumption: 100 Watt• Optional Special Features: Battery Backup |
| 96 | INSTRUMENT Trolley with two S.S Shelves, Frame made of stainless steel Mounted on five 7.5 cm. swivel castors. Wholly made of 304G stainless steel.Size: (30L x 18W X 32H) inch |
| 97 | INSTRUMENT Trolley with two S.S Shelves, Frame made of stainless steel Mounted on five 7.5 cm. swivel castors. Wholly made of 304G stainless steel.Size: (38L x 20W X 32H) inch. |
| 98 | Revolving Stool1. Four legs full SS.2. HT: 18-39inch (Screw adjt.) SS top dia: 30cm. |
| 99 | Double Bowl StandFull SS 304g with bowl. |
| 100 | Double Foot Step• Overall approx. step size:505mmL x 305mmW• First step height 230 mm and second step size 450 mm• Step made of full SS 304g |
| 101 | CRASH CART TROLLEY1. Overall Approx. Size: 37 Lx 19W x 60H inch.2. S.S tubular frame.3. Six removable plastic bins and two polystyrene lockable storage units with three drawers each.4. Four swivel Castors, 150mm dia. (Two with Brakes.)5. Complete with corner buffers, oxygen cylinder holders’ IV Rods’, cardiac massage board and electric lamp. |
| 102 | Electrical Work (As per the project requirement)• Conduits & bends• Switch boxes• Light boxes• Junction boxes• Wires• Switches & Plates• MCBs |
| 103 | Scrub StationHV electrical components should be in the junction box.a) 2 users fully automatic and foot-operatedb) 24 VAC-operated fascia.c) It should comply with LV requirements.d) The Bowl must be constructed in such a manner that it should eradicate the backsplash of water.e) Drainage should be precisely designed to avoid any overflowing.f) The sinks should have the capability to provide convenience and it should also work on water-saving concept.g) Material: Stainless Steelh) Color: Silver |
| 104 | Air ConditionerType - SplitCapacity - 1 Ton |
| 105 | Dustbin (Trio)Stainless Steel Frame, suitable for Operation Theatres. |
| 106 | O2 Outlet- B.S. type double Locking System including probe-oxygen |
| 107 | O2 Outlet for Pandent |
| 108 | B.P.C. flowmeter with Humidifier bottle & adaptor 0.15 LPM |
| 109 | OT Tubing Pipe O2Conversion Kit - Pin Index to Probe - 3 mtr Each - Oxygen |
| 110 | N2O Outlet- B.S. type double Locking System including probe - Nitrous |
| 111 | N2O Outlet for Pandent |
| 112 | OT Tubing Pipe N2O |
| 113 | B.S. type double Locking System including probe - Air 4 Bar |
| 114 | Air 4 Bar Outlet for Pandent |
| 115 | B.S. type double Locking System including probe - Vacuum |
| 116 | Vacuum Outlet for Pandent |
| 117 | Vacuum RegulatorWard Vacuum Unit with Regulator, Collection Jar of 600 ml with bracket .(For Wards) |
| 118 | Theatre Suction Trolly with 2000 ml jar Make : Classic |
| 119 | 12 mm Copper Pipe0.7 mm thickness Medical Grade EN - 13348 |
| 120 | 15 mm Copper Pipe0.9 mm thickness Medical Grade EN - 13348 |
| 121 | 22 mm Copper Pipe0.9 mm thickness Medical Grade EN - 13348 |
| 122 | Isolation Ball Valve Complete Set - 12 mm |
| 123 | Isolation Ball Valve Complete Set - 15 mm |
| 124 | Isolation Ball Valve Complete Set - 22 mm |
| 125 | Alarm for O2 & VACUUM |
| 126 | Alarm for O2, VACUUM, N2O & AIR 4 BAR |
| 127 | Semi-fowler Patient Bed with mattressFrame and Platform made of CRCA steel.Manual crank operated Single function bed featuring back rest position.Plastic/ABS Bed Head panels.Dimension: 1800-2000 L x 900 W x 600 H (mm) approx.Pre-treated and Epoxy Powder Coated.Semi-fowler Bed's 3 inches Mattress.Mattress Material: EP with PU, Foam and Raxine.Safety Side railings can easily be drop down. |
| 128 | Bed Side LockerFrame made of CRCA steel tubes/sheetsSingle storage box SS top On PVC shoesDimension: 400 L x 400 W x 800 H mm approx.Pre-treated and Epoxy Powder Coated |
| 129 | Bed Side StoolSS revolving topReinforced with M S FrameMade of CRCA steel tubesFoot-rest ring, On PVC shoesHeight adjustable 450 mm to 675 mmPre-treated and Epoxy Powder Coated |
| 130 | IV StandCRCA steel tube frame CRCA/ Plastic 5-pronged baseSS rod with double hookHeight adjustable by knob on 50 mm castersDimension: Base 575 mm diameterHeight adjustable 1150 mm to 2025 mm approx.Pre-treated and Epoxy Powder Coated. |
| 131 | Kick Bucket/BowlDia: 350 mmHeight: 850 mmSS Bowl & MS Frame |
| 132 | Wall Vinyl - 1mm Wall Vinyl |
| 133 | Ceiling CS - Calcium Silicate false ceiling - 8mm Board on GI structure |
| 134 | FLOOR - Supply, installation, fixing of seamless Semi Anti static conductive floor, as in OT shall be 2mm thick with covings, with welded joints with following specifications :- (i) Flooring in each operation rooms seamless with perfectly curved flash-covings . (ii) It shall have anti-bacterial and fungicidal properties. (iv) Flooring is a static-conductive, flexible homogeneous vinyl floor. |
| 135 | Semi Hermatically sealed Swing door Semi Hermatically sealed clean room door (Swing type door) in Room. Doors shall be designed to fit flush into the wall panel system on both sides. Doors shall be fabricated from PPGI. Standard 50mm panel shall have frame width of 50mm & shutter width of 45mm. The following accessories shall be part of the door :- Max 1.2X2.1mt ( Double Door )(a) Shutter Thickness 45mm(b) Stainless steel hinges(c ) SS 304 CE certified 'D' type handles on pull side.(d) Standard arm door closure(e) View panel along with self adhesive tape & silicone sealant.(f) Both side key operated locking arrangement.(g) SS 304 Kick plate.(h) Colour options avilable : (i) Off White (RAL9001/RAL9002), (ii) Cool Blue, (iii) Green, (iv) Deep Blue (RAL 5005) |
| 136 | Semi Hermatically sealed Swing door Semi Hermatically sealed clean room door (Swing type door) in Room. Doors shall be designed to fit flush into the wall panel system on both sides. Doors shall be fabricated from PPGI. Standard 50mm panel shall have frame width of 50mm & shutter width of 45mm. The following accessories shall be part of the door :- Max 0.9X2.1mt (Singe Door )(a) Shutter Thickness 45mm(b) Stainless steel hinges(c ) SS 304 CE certified 'D' type handles on pull side.(d) Standard arm door closure(e) View panel along with self adhesive tape & silicone sealant.(f) Both side key operated locking arrangement.(g) SS 304 Kick plate.(h) Colour options avilable : (i) Off White (RAL9001/RAL9002), (ii) Cool Blue, (iii) Green, (iv) Deep Blue (RAL 5005) |
| 137 | Semi Hermatically sealed Swing door Semi Hermatically sealed clean room door (Swing type door) in Room. Doors shall be designed to fit flush into the wall panel system on both sides. Doors shall be fabricated from PPGI. Standard 50mm panel shall have frame width of 50mm & shutter width of 45mm. The following accessories shall be part of the door :- Max 1.5X2.1mt ( Double Door )(a) Shutter Thickness 45mm(b) Stainless steel hinges(c ) SS 304 CE certified 'D' type handles on pull side.(d) Standard arm door closure(e) View panel along with self adhesive tape & silicone sealant.(f) Both side key operated locking arrangement.(g) SS 304 Kick plate.(h) Colour options avilable : (i) Off White (RAL9001/RAL9002), (ii) Cool Blue, (iii) Green, (iv) Deep Blue (RAL 5005) |
| 138 | GEM Item -Atlas N3--M/S M B S INDIA Anesthesia WorkstationAtlas N3URUnregistered BrandManufactured by: M/S M B S INDIA(Atlas N3) |
| 139 | Add 18 % GST |
| 140 | Add 1% Labour Cess Please Enable Macros to View BoQ information |
