Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | BOQ Item No. 01 to 30 Common for Jobs Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed. |
| 2 | M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed. |
| 3 | Demolition of cement concrete (reinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed. |
| 4 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in soft/loose soil. |
| 5 | Excavation in trenches not exc 1.5 mtr wide & not exc. 1.5mtr depth for foundation, manholes etc and getting out soft/loose soil complete all as specified and directed. |
| 6 | S&F for mild steel as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of FE410-W (Gde E-250) |
| 7 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 8 | S&F of pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in room covering/cladding to wall, including ridge cover fixed with self tapping screws etc all as specifed. |
| 9 | S&F exterior tiles(Heavy duty) of superior quility 400x400x10-12MM thick of approved size/design/shade set and jointed in neat cement slurry & pointed in white or coloured cement to match as in floor over and including 20mm thick screed bed in cm 1:4 complete all as specified and directed. |
| 10 | Taking down cement or cement lime plaster any description from brick or stone walls/ceiling etc including raking out joints, hacking for key & scrubbing down with water all as specified. |
| 11 | M&L for rendering 15mm thick in CM 1:4 on brick work or concrete surface of wall and finished surface even and smooth without using extra cement all as specified and directed. |
| 12 | Preparation of plastered surfaces and applying two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, over a coat of 2mm thick putty and primer of required shade and colour complete, as per manufacturer's specification over Complete all as specified and directed |
| 13 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area exc 1.5 Sqm but n.exc 4 sqm each all as specified. |
| 14 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area n.exc 1.5 Sqm each all as specified. |
| 15 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 16 | S&F Factory made 30 mm thick 100% solid WPC (Wood Polymer Composite) solid prelam both side 14 micron Flush door shutter with 10mm deep CNC moulding design of required size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 17 | S&F 30mm thick factory made solid WPC (Wood plastic composit) moulded glzed door shuter with wire mesh in 08 number of division with brown wood grain texture including SS wire mesh (G-304) 0.36 mm minimum dia of wire and average width of aperature 1.4mm with XPM Aluminium alloy wire cloth of wire shall to be fixed with 15x15 square tube in side rails with screwing 8x28 heat metel zink coated screws can be remove of fix again after changing of wire mesh needed. The density not less then 780kg /Cum shall be as per manufacture instruction complete all as specified and as directed |
| 18 | Supply & fixing Factory made uPVC prelem colour three track three panels sliding window with fly proof S.S wire mesh and 5 mm thick glass (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 112 x 52mm & sash 42x 68 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi- chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. |
| 19 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apeerture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, all as directed. |
| 20 | M&L, 20 mm thick granite (of any type and colour ) work (table rubbed and polished ) in steps, Jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of granite complete all as specified. |
| 21 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 22 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, all as specified and directed |
| 23 | M&L Glazed ceramic tiles (coloured) in vertical surfaces 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 10mm thick rendering in cement mortar 1:3 complete all as specified and directed. |
| 24 | M&L for Plastering by using ready mix mixture of thickness 15 mm thick with water proofing liquid and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge. |
| 25 | Repair to plaster by using readymix mixture of thickness 10 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge |
| 26 | Repair to plaster by using readymix mixture of thickness 5 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the Celing surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge |
| 27 | M&L Prepration new/old plastered surfaces and applying two coat of white wash on ceiling all as specified. |
| 28 | M&L for cement concrete 1:3:6 type C2, 75 mm thick as in plinth protection and flooring and finishing the surface even and smooth without using extra cement. |
| 29 | Demolition of reinforced cement concrete as in self etc (reinforcement cut as reqiured to faciliate demolition) complete all as specified and directed. |
| 30 | M&L for preparation of Old/New steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified. |
| 31 | BOQ Item No. 31 TO 60 FOR JOB NO. LSA/DWP/29/LBW/25-26 M&L Cement concrete1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete |
| 32 | S&F mild steel joist, channel, angle, or tee sections as in posts fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe-410-W (Gde E-250) |
| 33 | Surface excavation not exc 30 cm deep averaging 15 cm deep and getting out in soft/ loose soil. |
| 34 | M&L hardcore of gauge of broken brick n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and rammed to a true surface. |
| 35 | M&L 100mm thick PCC type D-2 1:4:8 (40mm graded stone aggregate) for sub base. |
| 36 | M&L for rendering 15mm thick in CM 1:6 on brick work or concrete surface of wall and finished surface even and smooth without using extra cement all as specified and directed. |
| 37 | Complete removal of existing treatment by scrapping with Trucare Wall Sander: L- 01/H-01 (having mechanical vacuum mechanism) or equivalent having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc. by skilled labour NOTE: Work Executed by OEM under the Provision of MOU |
| 38 | M&L waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm, over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and . Sanding of the putty surface with TruCare Wall Sander: L- 01/H-01 or equivalent (having mechanical vacuum mechanism) having RPM not less than 1500, sannding pad of 240 Grit or above having dia of 7\\"/9\\" to make the surface free from dust etc. by skilled labour.Step 1) Mix the putty powder by adding 40-50% water and mix it with Trucare Putty mixer(Trucare Putty mixier with min 1400 W power havinng mixer rod of industrial stell grade 45 with the mixing capacity of min 2.5 kg putty per minute).Step 2)Apply the first coat the prepared mixer with the help fully automatic airless spray machine of putty application of Trucare Graco Spray Machine(Model: EH 230 DI) or equivalant having a DC electric motor of 3.3 KW having flow speed of max 6 ltrs per minutes with a maximum pressure 230 bar having maximum tip size 0.041\\" Step (3) Allow 6-8 hrs time to dry the putty surface. NOTE: Work Executed by OEM under the Provision of MOU |
| 39 | M&L for one coat of acrylic water based exterior grade primer @0.9 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application Trucare Graco or equivalent having an electric motor of min. 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent quotes as per manufacturer instructions complete all as directed. NOTE: Work Executed by OEM under the Provision of MOU |
| 40 | M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up Resistance with low VOC less than 50 G/L , Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water in 5:2 ratio applied over priming coat with fully automatic airless spray machine of paint application of Trucare Graco or equivalant having an electric motor of min. 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint with 8 years performance warranty from Manufacture and instructions complete all as directed. NOTE: Work Executed by OEM under the Provision of MOU |
| 41 | S&F 12 mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including frosted film with logo and letter printing, cutting to shape, drilling holes required and pivot at top fance type glass handle of size not less than 300 mm on both sides of shutter to match with colour of glass shutter top and bottom aluminium rail with suitable locking arrangement and all necessary fitting complete all as specified and directed. |
| 42 | M&L as for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, with & including replacement of floor tiles if any broken during repair work and making good disturbed surfaces matching to the existing surfaces complete all as directed. |
| 43 | S&F 18mm HDMR boards laminated on both sides with 7mm mica on internal sides and 1 mm decorative mica on outer visible sides. |
| 44 | S&F for stainless steel wardrope trolly of any shape and size with side sliding roller clip over stainless steel channel on both side fixed with steel size 33x20x8 inches with sliding rails complete. |
| 45 | S&F for stainless steel modular type basket of size 20x16x8 inches with side sliding roller clip over stainless steel channel on both side fixed complete all as specified and as directed. |
| 46 | S&F for stainless steel modular type basket of size 20x16x6 inches with side sliding roller clip over stainless steel channel on both side fixed complete all as specified and as directed. |
| 47 | S&F for stainless steel modular type basket of size 20x16x4 inches with side sliding roller clip over stainless steel channel on both side fixed complete all as specified and as directed. |
| 48 | S&F for Stainless steel half circle modular type basket of size 28x20x4 inches over stainless steel pipe revolving type with sliding rails complete all as specified and directed. |
| 49 | S&F for stainless steel modular type basket of size 20x20x4 inches (pull out 3 shelf) with side sliding roller clip over stainless steel channel on both side fixed complete all as specified and as directed. |
| 50 | S&F for stainless steel modular type basket of size 20x20x12 inches (pull out 3 shelf) with side sliding roller clip over stainless steel channel on both side fixed complete all as specified and as directed. |
| 51 | S & F Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate for cup board / cabinet shutters complete all as specified and directed |
| 52 | S&F 250 mm long stainles steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 53 | S&F for stainles steel barrel tower bolts 200 mm of extruded section and fixed. |
| 54 | S&F 125 mm size stainles steel handles fabricated type extruded section |
| 55 | S&F Auto hinges stainless steel hinges medium weight and fixed |
| 56 | S&F Butt hinges 125 mm stainless steel hinges medium weight and fixed |
| 57 | S&F powder coated Anodised aluminium Grill (anodised tranparent of dyed to required shade according to IS1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the exiting window frame with CP brass/ stainless steel screws @200 mm centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Enginer-in-charge. |
| 58 | Dismantling of stone slabs and tiles of any description or thickness in floors, platform, aprons etc laid bedded and pointed in any mortar |
| 59 | S&F vitrified ceramic tiles dark/light shade digital tiles/(double charged), 10mm thick (square/ rectanglar) polished , exceeding 0.42 sqm of each tiles not exceeding 1.00 sqm, in floors etc. laid over 15mm thick screed bed 1:6 , set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified. |
| 60 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick(square/ rectanglar) area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm in floor including screed bed 15mm thick or beding layer for laying floor finishes CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match. |
| 61 | BOQ Item No. 61 TO 86 FOR JOB NO. LSA/DWP/43/SRW/25-26 Dismantling of Bricks (laid flat or on edge) or brick tiles in roof, channels, kerbs, aprons, etc. |
| 62 | M&L cement concrete type B-1, 1:2:4 (20mm graded aggregate) on roof slab all as specified and directed. |
| 63 | Rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1:4, mixed with liquid water proofing compound finished even and smooth without using extra cement . (Liquid water proofing compound to be measured paid separately) complete all as specified and directed. |
| 64 | Supply only Liquid water proofing compound complete all as spesified and directed. |
| 65 | Material and labour for applying fibre reinforced liquid applied elastomeric membrane made of PU Poly urethane with self priming in 1:1 ratio and let it dry for 4-6 hrs. Further apply 2 coats of undiluted water proofing treatment fibre reinforced liquid applied elastomeric membrane made of PU Polyurethane in a gap of 4-6hrs. The applied material should have specific gravity of 1.25g/cc with minimum recommended coverage of 2- 2.2 Kg/Sqm in 2-3 coats to built DFT of 1.2mm the cured membrane shall exhibit - 1. ) Tensile Strength ASTM D412 : 1.4-2.5 MPa2.) Elongation ASTM D412 : 400-500%3.) Adhesion Strength : 1.5N/sqm as per ASTM D45414.) Crack Bridging Ability : >3-4mm as per AS/NZS 4548:5:19995.) Water Permeability : NIL as per DIN 1048 (c) Separation layer of geo-textile membrane 40-45gsm with overlaps of 50mm in both directions over the Ist coat when the surface is still tacky. |
| 66 | M&L Cement concrete by using readymix mixture as in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less |
| 67 | Forming Contraction (Dummy) joints 65mm deep x 10mm wide, cutting with PCC cutting machine and filled with sealing compound |
| 68 | Forming Construction joint 30mm deep x 10mm wide filled utting with PCC cutting machine with sealing compound |
| 69 | M&L for machine cut kota stone slab flooring 19-20mm thick over cement screed bed 15mm thick in CM 1:6, base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified. |
| 70 | M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified. |
| 71 | Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand |
| 72 | From work to roof slab with projection including edges with rough finished surfaces of concrete complete all as specified and directed. |
| 73 | M&L for reinforced cement concrete 1:11/2:3 (Nominal mix) using 20 mm graded aggregates as in slabs supported on walls, beams, column etc complete all as specified and directed. |
| 74 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 75 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area exc 1.5 Sqm but n.exc 4 sqm each all as specified. |
| 76 | S&F Factory made 30 mm thick 100% solid WPC (Wood Polymer Composite) solid prelem both side 14 micron Flush door shutter wit 10mm deep CNC moulding design of required size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 650 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 77 | S&F 250 mm long stainless steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 78 | S&F for stainless steel barrel tower bolts 200 mm of extruded section and fixed. |
| 79 | S&F 150 mm size stainless steel handles fabricated type extruded section ,ISI marked all as specified |
| 80 | S&F Butt hinges 125 mm stainless steel hinges medium weight and fixed |
| 81 | S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or wall including down all as specified and directed. |
| 82 | S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall all as specified and directed by Engineer-in-charge. |
| 83 | S&F 110mm bore PVC (SWR) bends, any radius. |
| 84 | S&F in repairs Steel rolling shutter 1.25 mm thick, with gear operated type with chain wheel and hand chain as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer : erected in position as indicated, complete all as specified and directed. |
| 85 | S&F Safety lever locks mild steel with 4 levers for rolling shutters |
| 86 | S&F Ball bearing for rolling shutters |
| 87 | BOQ Item No. 87 TO 132 FOR JOB NO. LSA/DWP/37/SRW/25-26 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 88 | S&F for in repair three layer rotational moulded polyethylene water storage tank cylindrical hoisted & fixed in position incl dismantiling water tank complete all as specifed capacity 1000 ltrs. |
| 89 | S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density Plastic ball Screwed for iron pipe and fixed (Minimum weight -210 gms. Make Prayag/Polytuff |
| 90 | S&F 15 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down |
| 91 | S&F 20 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down |
| 92 | S&F vitrified ceramic tiles dark/light shade digital tiles/(double charged), 10mm thick (square/ rectanglar) polished , exceeding 0.18 sqm of each tiles not exceeding 0.38 sqm, in floors etc. laid over 15mm thick screed bed 1:6 , set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified. Make : Somany,/Johnson/Kajariya |
| 93 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. |
| 94 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 95 | Ditto item No. 94 but of Frame size 65x 125 mm |
| 96 | S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 97 | S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putty/Aluminium beads in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces ground or obsecured to one side complete all as specified. |
| 98 | S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified. |
| 99 | Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 100 | S&F 250 mm long stainless steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 101 | S&F for stainless steel barrel tower bolts 200 mm of extruded section and fixed. |
| 102 | S&F for stainless steel barrel tower bolts 150 mm of extruded section and fixed. |
| 103 | S&F 125 mm size stainless steel handles fabricated type extruded section ,ISI marked all as specified |
| 104 | S&F 150 mm size stainless steel handles fabricated type extruded section ,ISI marked all as specified |
| 105 | S&F Butt hinges 125 mm stainless steel hinges medium weight and fixed |
| 106 | S&F Butt hinges 100 mm stainless steel hinges medium weight and fixed |
| 107 | S&F 18 mm thick solid WPC board of density 600kg/Sqm one side prelaminated decoratiove teak face and other side white and balancing as in kitchen shelf, shutters etc including chawkats and all fitting accessories etc including dismantling, complete all as specified and directed |
| 108 | S&F 150mm long fancy stainles steel handle for cupboard & wardrobe shutter complete all as specified and as directed by Engr-in-charge |
| 109 | S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws. |
| 110 | S&F stainless steel drapery curtain rods standard quality dia not less than 25mm with fancy type stainless steel latoo at both ends and Stainless Steel Bracket for middle support as required all as specified and direced as approved by GE. |
| 111 | S&F Vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts flushing cistern and flush pipe ). and trap including connection to drain (or out going pipe) and to flushing pipe anti sphonage pipe etc complete including flush pipes and all joints add if fixed in repairs. |
| 112 | S&F Plastic water closet seat cover coloured/white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed. |
| 113 | S&F in repair health faucet for EWC CP hand hold with flexible pipe 1.5m long complete set all as specified. |
| 114 | S&F in repairs 15mm dia CP two way tap consisting angle valve to control water suitable for jet cleaner all as specified. |
| 115 | S&F 10 Litres capacity PVC valve less syphonic action type flushing cistern low level, white with inlet ball valve float and handle including brackets connection to pipes and fixing of lever if any joint between flushing pipe and socket of WC pan pre-made |
| 116 | S&F in repair Vitreous china wash hand basin white angle back size 550x400 mm including 32 mm dia CP waste coupling long screwed shank fly nut flanged end and embedded in lead to waste pipe excluding piller taps complete fixed specified and directed by enginner -in-charge |
| 117 | S&F 110mm PVC (SWR) junction single (single T) equal or unequal |
| 118 | S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or wall including down all as specified and directed. |
| 119 | S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall all as specified and directed by Engineer-in-charge. |
| 120 | S&F 110mm bore PVC (SWR) bends, any radius. |
| 121 | S&F PVC (SWR) bends any radius of 75 mm dia all as specified. |
| 122 | S&F PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement |
| 123 | S&F 15mm dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, scresed down screwed for iron pipe or for brass ferrule and fixed both ends for iron pipe or for unions |
| 124 | S&F brass chromium plated wall mixer for mixing hot & cold water in 3-in-1 with 1.50m long flexible lead & screwed down for iron pipe of 15mm bore all as specified and as directed. |
| 125 | S&F 125 mm dia CP brass shower rose with or without swivel joints any size including fixing to steel pipe or union add if fixed in repair all as specified and directed |
| 126 | S&F in repair 15 mm dia Pillar tap cast copper alloy chromium plated fancy type with capstan head and cup screwed down screwed for G I pipe or for brass ferrule all as specified. |
| 127 | S&F 15mm dia fancy type chromium plated Stop/angle/Conceled valve/cast copper ally screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed to GI Pipe. |
| 128 | S&F CP brass towel rails 20 mm dia and 600 mm long fixed as in repair incl chromium plated brass screw and wooden / cleats |
| 129 | S&F in repairs bevelled edge 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified |
| 130 | S&F PVC connection of 15 mm bore 600 mm long with brass coupling on both ends of superior quality all as specified.PTMT nuts fixed as in repair. |
| 131 | S&F in repairs 32 mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm 45gms/40mm-60 gms) |
| 132 | S&F in repairs 32mm dia PVC waste pipe approx 900mm long for sink/WHB complete all as specified. |
| 133 | BOQ Item No. 133 TO 158 FOR JOB NO. LSA/DWP/24/SRW/25-26 Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 134 | Dismantling of RCC posts or struts any section including taking out embedded portion and making good disturbed ground concrete, brick work, masonry etc |
| 135 | Removing surplus excavated material (soil) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. |
| 136 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. |
| 137 | M & L for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 138 | M&L for RCC design mix (M-25) using 20 mm graded stone aggregate for foundation footings plinth beams, cloumns etc all as specified and directed by Engineer -in-charge. Note Reinforement shall be measured and paid seperately under relevent item. |
| 139 | M&L RCC design mix (M-25) for Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. |
| 140 | M & L M-25 for RCC type B-1 as in lintels, beam etc. over 1.5mtr span. |
| 141 | M&L RCC design mix (M-25) for using 20 mm graded aggregates as in slabs, complete all as specified and as directed. |
| 142 | M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed. |
| 143 | M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed. |
| 144 | Ditto as per above item but to sides and soffits of beams , lintels etc. |
| 145 | M & L for use and waste of formwork to slab with projection including edges with rough finished surfaces of concrete complete all as specified and directed. |
| 146 | M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 147 | M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 148 | M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed. |
| 149 | M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed. |
| 150 | S & F of galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, straining bolts at ends, staples or steel pins etc.Incl dismantling of old barbered wire ( Each line wire to be measured) complete all as specified and directed. |
| 151 | S & F PVC pipe [SWR] single socketed in any length with rubber ring joints laid in trenches or in floor for weep holes 110 mm bore all as spcified and directed |
| 152 | M & L for preparation of new or previously un-treated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 153 | M&L PCC (1:4:8) type D-2 (using 40mm graded agg) 75mm thick as in below of plinth beam as specified and directed by Engr-in-Charge. |
| 154 | M&L for cement concrete type C2, 1:3:6 using 40 mm graded stone aggregate as in embedding of fencing post etc,. |
| 155 | S&F for mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc,.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed . |
| 156 | M&L for preparation of new surface of steel and applying two coat of synthetic enamel paint over one coat of red oxide area over 10cm width or girth |
| 157 | M&L for 20 mm thick granite table rubbed and polished as required fixed on pillars over 15 mm thick rendering in CM 1:4 complete all as specified and directed. |
| 158 | M&L for mild steel framed structural work as in doors or gates of angle or ther section with gusset plates, rairls braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or slinding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing of Fe-410-0 (Gde E- 250 complete all as directed by Engr-in-Charge. |
| 159 | COMMON EnM ITEMS M&L for point re-wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm and earth continuity conductor with 1.5 sqmm colour code drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes 1mm thick and modular cover plate with frame of approved colour for mounting modular switches, sockets etc as required for the following. |
| 160 | All as per Item No 160 hereinbefore but for One 5 A socket outlet on independent Board all as specified. |
| 161 | All as per Item No 160 hereinbefore but for One 5 A socket outlet on same Board all as specified. |
| 162 | M&L for point re-wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm and earth continuity conductor with 2.5 sqmm colour code drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes 1mm thick and modular cover plate with frame of approved colour for mounting modular switches, sockets etc as required for the following. |
| 163 | Supply and fix Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.PVC pipe 25 mm dia for protection of cables all as specifid |
| 164 | Supply and fix Modular switch one way 6A 230V AC 50 HZ SP one module all as specified. |
| 165 | Supply and fix Modular switch one way 16A 230V AC 50 HZ SP one module all as specified. |
| 166 | Supply and fix Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module all as specified. |
| 167 | Supply and fix Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module all as specified. |
| 168 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning 40 to 63 Amp capacity all as specified. |
| 169 | S&F modular bell push single pole 1 module 6 Amp, 240 volt all as specified. |
| 170 | S&f call bell , ding dong / musical AC single phase 230 volts all as specified. |
| 171 | S&F Ceiling rose PVC polycarbonate all as specified. |
| 172 | Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 4 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 4 Sqmm drawn through and including PVC Conduit pipe 25 mm dia with all fittings all as specified. |
| 173 | Material and labour Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 connected to earth testing point including necessary excavation, earth work, PCC pit ,RCC cover 1:2:4 B1 with 8 mm dia MS rounds 1.5 kgs, funnel ,watering pipe etc. all specified and directed including testing on completion all as specified. |
| 174 | Cutting chases in concrete wall/stone for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 20 cm girth and matching wall color. |
| 175 | Supply and fixing of Solar integral AIO Post-top luminaire with solid polycarbonate housing, reliable &robust construction with IP65 protection, suitable for pole entry dia of 60mm, having Min 3000 system lumens, suitable for 12hrs (Dim mode) Autonomy. Lighting mode selectable for 2H/4H/6H along with the CCT 3000K/4000K/6500K by remote. Lithium Pherrophosphate Battery capacity min [email protected]. Panel capacity min 13Wp, CRI >=70, System Efficacy >165Lm/W & system wattage should not be more than 18W ± 2%, if wattages increases then the size of battery & panel shall also be increased in similar percentage to maintain equal autonomy of the system. Microwave Motion Sensor 5.8GHz, <=25mW. Life class of LED System 25000hrs@L70. LED Make: CREE/ NICHIA/ LUMILEDS/ OSRAM. CE Certified, charger efficiency >90%. The PV module should be made up of crystalline silicon solar cells \\"Mono-Crystalline\\" and must have a certificate of testing conforming to IEC 61215 Edition II / BIS 14286 & IEC 61730-1,2 IEC60598, Operating temp 0℃ to 55℃, certifying above given parameters all reports shall be from In-house NABL or IECQor any international accredited Laboratory complete |
| 176 | M&L in renewal distribution board, SPN 8 ways, power coated, CRCA sheet degree of protection IP-43, IK-09 with reversible double door, recess mounted, having insulated 100 Amp tinned coper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earhting connection, blanking plates in unused spaces as required complete. |
| 177 | M &L for Excavation in trenches not exc 1.5 m wide and not exc 1.5m deep for laying of pipe, cable etc and getting out in soft/loose complete . |
| 178 | M&L for Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete . |
| 179 | M &L for Removing surplus excavated material to a distance not exc 50 meter and depositing where directed at level not exc 1.5m above the starting point complete. |
| 180 | S&L DWC HDPE Pipe along with all aceessories like socket , bend,couplersetc ISI mark as per IS: 16205 (PART-24) including cutting,jointing,laid in trenches,wall , floor,etc as required 63 mm outer dia and 50 mm inner dia complete |
| 181 | Supply and fixing LED building security light of 36W Led Street Light made up of pressure die cast aluminium housing with Polycarbonate cover and unique road optics for better uniformity. The luminaire shall be with higher ingress protection IP66 and impact resistance of IK07. Operating voltage range: 140-270V/50Hz, Lumen efficacy of LED >120Lm/W, CRI≥70, CCT-5700K, & SDCM<5. Powered by built-in potted LED driver gives constant light over wide voltage range. Shall have High Voltage cut-off@325V & safety from 440V (P2P) for 8 hours. Surge protection 4 kV, Power factor ≥0.95, THD ≤10 complete including 25x3 mm flat iron with bracket of GI pipe light grade 25 mm dia and length not less than 1.2 mtr end of GI pipe suitable for street light fitting complete .Note: Heat sink of aluminium housing should be such that LED junction temp shall not rise above 90 degree cel. |
| 182 | EnM Items for Job No. LSA/DWP/29/LBW/2025-26 Supply and fix in repair of MCB DB TPN 4 way double door type suitable for TP/FP including necessary dummy plate and necessary civil works all as specified. |
| 183 | Supply and fix MCB SP 230V, 6-32 Amps capacity all as specified and directed. |
| 184 | Supply and fix Modular Regulator 230V AC 50 HZ SP two module all as specified. |
| 185 | Supply and fixing of wall/surface mounted integrated batten LED light luminaire of 4ft length with a system wattage of 20-22W with a nominal system lumen output of 2000-2200 lumens and a minimum system efficacy of 100Lm/W. CCT shall be 6500K and CRI ≥ 80. Housing shall be extruded aluminimum with powder coating & with IP20 protection, The luminaire shall meet IP20 rating with surge protection of 2.5KVA, THD ≤10% and PF ≥ 0.95, 2P20,CRI>80,flicker Free. Flicker should be below 5% ), lifetime (LED and Electrical Circuting) of Min 50000 burning hours with 70% of initial Lumen maintaine dtill Life ends, CCT5700 degree K/6000K As per ANSI Bin SDCM<3, minimum power consumption should not be more than the specified rating and fixture shall be relevant BIS Std and trademark certificate (TC). Manufactures word mark/name engraved/embossing/ screen printing on housing complete in all respect incl connections with suitable size FRLS, PVC insulated copper conductor cable and earthing etc. as reqd with min 5 yrs OEM warranty. LM 79 & LM 80 test report from NABL Lab for all tests reqd for LED fixtures and BIS shall be submitted. Note : Heat sink of aluminium housing such that LED junction temp shall not rise above 90 degree C. |
| 186 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified. |
| 187 | S&F in replacement decorative wall mounted fancy light fitting made up of brass rubi lamp brand Single handed including of bulb of 9-15 watts covered by glass complete all as specified. |
| 188 | S&F LED COB Light 6-9 Watt all as specified. |
| 189 | Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 6 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 6 Sqmm drawn through and including PVC Conduit pipe 25 mm dia with all fittings all as specified. |
| 190 | Supply and fixing ceiling fans remote operated complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with copper winding incl remote all as specified. |
| 191 | Supply and fixing of wall fan of 300 mm sweep, 220 - 240 volts, AC, 50 Hz 1330 RPM, 55 Watts power input, air delivery 65 Cum/min with all accessories complete. Make:- Bajaj/Havells/Crompton/Usha |
| 192 | Supply and fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one 20 amps SPN MCB all as specified. |
| 193 | Supply and fixing Exhaust fan PVC body 250 mm sweep working on single phase supply incl. all accessories including electrical connection with required wire complete all as specified. |
| 194 | EnM Items for Job No. LSA/DWP/24/SRW/2025-26 M&L in renewal distribution board, SPN 8 ways, power coated, CRCA sheet degree of protection IP-43, IK-09 with reversible double door, recess mounted, having insulated 100 Amp tinned coper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earhting connection, blanking plates in unused spaces as required complete. |
| 195 | Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete |
| 196 | EnM Items for Job No. LSA/DWP/37/SRW/2025-26 Taking down carefully copper/aluminium point wiring ( light, fan, socket , bell or power) complete including all electrical fittings & fixtures(DBs,submain,cables etc) all as specified and directed by Engineer-in-charge. |
| 197 | Supply and fix MCB SPN 230V, 32-63 Amps capacity all as specified and directed. Make:Legrand/Havells/L&T |
| 198 | Supply and fixing of wall/surface mounted integrated batten LED light luminaire of 4ft length with a system wattage of 20-22W with a nominal system lumen output of 2000-2200 lumens and a minimum system efficacy of 100Lm/W. CCT shall be 6500K and CRI ≥ 80. Housing shall be extruded aluminimum without powder coating & with IP20 protection, The luminaire shall meet IP20 rating with surge protection of 2.5KVA, THD ≤10% and PF ≥ 0.95, complete all as specified and directed by Eng-in-Charge. |
| 199 | Supply and fixing DB,powder coated, CRCA sheet, degree of protection IP-43with reversible double door,recess type, 100 Amp tinne dcopper busbar, neutral bus bar 6TPN 415V 4Way complete. |
| 200 | Supply and fixing Digital storage water heater (Geyser) Square type of capacity 25 ltrs, 230 volts, power consumtion 230V, vertical type, Rated pressure 5.6 bar pressure rating more than 8 bar suitable for high rise buildings,rust and shock proof ABS Outer body for lomg life,Stainless steel inner tank of 304 grade,65 MPa bar pressure,colour changing lights that change from blue to amber to indicate the hotness of water,automatic shut off including four nos of rag bolts and making the elctrical / water supply connection including testing after installation complete all as specified and directed by Engr-in-Charge. |
| 201 | Supply and fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one 20amps SPN MCB all as specified and directed |
| 202 | M& L for XLPE cable of size 50 sqmm 3.5 core |
| 203 | S&F ceiling fan 1200mm BEE star rated 5 with brush less less direct current (BLDC) motor, class insulation B three no blade upto 90cm long down rod, canopies, shackle kit, safety rope, copper winding, PF not less than .9, service value (CM/M/W? minimum 6.00, air delivery minimum 210 cum/min, 350 RPM (Tolerence as per IS : 374-2019), THD less than 10%, remote unit for speed control and all remaining accessories including safety pin, nut bolts , washers, temparature rise 75 degree C (max), insulation resistance more than 2 mega ohm suitable for 230 volts, 50 hzs including remote control. |
| 204 | S&F fresh air fan of size 300mm sweep metal body complete with louvers connecting up including suitable size three three core flexible copper cable from ceiling rose to fresh air fan as required complete. |
| 205 | S&F 415 volts, 10KA, curve miniature circuit brreaker, 4 pole current carrying capacity 199 amp complete. |
| 206 | EnM Items for Job No. LSA/DWP/43/SRW/2025-26 S&F in renewal MCBs of 'C' series having breaking capacity 10 KA, ISI marked incl reqd wiring connections with copper lugs of suitable size provided in MCB DBs complete. (a) SP 6 to 32 A |
| 207 | S&F in renewal MCBs of 'C' series having breaking capacity 10 KA, ISI marked incl reqd wiring connections with copper lugs of suitable size provided in MCB DBs complete. (b) SPN (or DP) 32 A |
| 208 | Supply and fixing in renewal of wall/surface mounted integrated batten LED light luminaire of 4ft length with a system wattage of 20 watt , power coated die cast/extruded aluminium body (thickness>1.20mm) or CRCA sheet body (Thickness>-.50mm) and construction as per IS:10322 with driver (Replaceable) as per the reqmt with driver efficiecy >85%, system lumen efficacy 120lm/Watt output, operating voltage AC 140-270 volts, 50Hz, operating temp rang-15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with short and open ckt protection, THD<10%, PF>.95, IP20, CRI>80, Flicker free (flicker should be below 5%), life time (LED & electrical circuitary) of min 50000 burning horus with 70% of initial lumen maint till life ends, CCT 5700 degree K (As per ANSI Bin), SDCM (Std deviation color matching)<3, max power consumption should not more than the specified rating and fixture shall be of relevant BIS standard and std and trade mark cert (TC). Manufactures word kark/name engraved/embossing/screen printing on housing complete in all respect incl connections with suitable size FRLS, PVC insulated copper conductor cable and earthing etc as reqd with min 5 years OEM warrenty. LM79 & LM80 test report from NABL lab for all tests reqd for LED fixtures as BIS shall be submitted complete.Note:- Heat sink of aluminium housing such that LED junction trmp shall not rise above 90 degree Cel. |
| 209 | Supply and laying XLPE Insulated armoured electric heavy power cable with aluminium stranded conductor ,1100 volts grade, cross sectional area 16 sqmm x two core complete Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
