|
| 1 | Demolition of brick work or stone / boulder masonry/ precast concrete block masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish complete all as directed by the Engr-in-Charge. |
| 2 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and including setting in mortar 1:4 complete all as specified and directed. |
| 3 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of 10cm thick, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) n exc. 10 cm in width and including setting in mortar 1:4 complete all as specified and directed. |
| 4 | M&L for cutting holes in brick walls n exc half brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed. |
| 5 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish complete all as specified and directed |
| 6 | M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 7 | M & L for rendering 15 mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item). |
| 8 | Sypply only Integral waterproofing compound conforming to IS 2645 (2003) complete all as specified and directed. |
| 9 | M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of oil emulsion distemper over a coat of alkali resistant primer and over one or more coats of wall care putty to a smooth surface complete all as specified and directed. |
| 10 | M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 11 | Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 12 | Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. |
| 13 | S&F 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 14 | S & F 30 mm thick, Flush shutters, solid core construction, with block board core and plywood both face panels, commercial type on both sides complete all as specified and directed. |
| 15 | S & F 35 mm thick, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 16 | S & F 30 mm thick, second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed. |
| 17 | S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 18 | S & F 300 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 19 | S & F 100mm long, Butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 20 | S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 21 | S & F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 22 | S & F in repairs 300 mm long, mild steel, ordinary rat tail rod pattern springs incuding roller and roller plate complete all as specifed and directed. |
| 23 | S & F in repairs Aluminium (Die cast) body door Closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed. |
| 24 | M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed. |
| 25 | Dismantling timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and directed. |
| 26 | S&F second class hard-wood wrought timber as in scantlings timber framed and fixed, complete all as specified and directed. |
| 27 | M & L preparing new surfaces of wood and wood based materials, of any description and girth, not otherwise described, and treated with tar or coal tar black paint backs of chowkats, area tarred exc 0.1 sq. m but n exc 0.5 sq. m each complete all as specified and directed. |
| 28 | S & F Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. and anodised aluminium fittings such as peg stay 150mm long (01 No), hinge type B-21, 100mm long (02 Nos) and suitable size of handle complete all as specified and directed. |
| 29 | S & F Powder coated aluminium (minimum thickness of powdercoating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with requiredEPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chargecomplete all as specified and directed. |
| 30 | S & F 75mm long mortice latch with two levers (vertical type), aluminium, anodised body complete all as specified and directed. |
| 31 | S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 32 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete as per specification and drawing and as directed. |
| 33 | S & F 125 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 34 | S & F 75mm long, Butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 35 | S & F 125 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 36 | S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 37 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. |
| 38 | S & F 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 39 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed. |
| 40 | S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 41 | All as per Serial item No. 40 above but except sheet complete ditto. (Note: Old serviceable sheet as obtained from dismantling item here-in-before shall re-used) |
| 42 | S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 43 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ snap grid frame etc complete all as specified and directed. |
| 44 | S & F aluminium Anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium T section of size 38mm x 25mm x 1.5mm thick for main runners, 25x25x1.5mm thick for cross runner and angle size 25x25x1.5mm thick alongwith wall suspended and including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to ceiling members in proper position, fixed with aluminium staple on snap grid as per manufacturer's instructions including 6 mm thick non asbestos E-board, HSPC, designer fixed to frame complete all as specified and directed by the Engr-in-Charge. |
| 45 | Taking down wall panelling and similar work complete all as specified and directed. |
| 46 | S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing and including 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed. |
| 47 | M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed. |
| 48 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish complete all as specified and directed. |
| 49 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 50 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 51 | M & L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 52 | M & L for Glazed, ceramic, coloured tiles of size 300mm x 200mm x 6-7mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 53 | Supply, laying, connection and testing, 20mm bore, cPVC pipes SDR 13.5 pipes & plain cPVC SDR 11 fittings on walls/ceiling or laying in floors, etc and including taking up or down un- serviceable pipes complete all as specified and directed. |
| 54 | Supply, laying, connection and testing, 25mm bore, cPVC pipes SDR 13.5 pipes & plain cPVC SDR 11 fittings on walls/ceiling or laying in floors, etc and including taking up or down un- serviceable pipes complete all as specified and directed. |
| 55 | S & F 24 mm outer dia, stainless steel, curtain rail/rod, heavy duty, minimum 1mm wall thick including brackets, side holder and rings etc fixed to /wall etc complete all as specified and directed.(Note: (i) Stainless steel decorative finials and stainless steel brackets shall be provided for each leangth of curtain rail/rod and cost of the same shall deemed to be included in the unit quoated rate. (ii) Length of of curtain rail/rod shall only be measured for payments) |
| 56 | M & L for Mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 57 | S & F in repairs Vitreous China Rimless Single Piece WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern Fittings, Size: 395x710x720 mm, P Trap - 180 mm and all fittings and fixtures including connection to outgoing drain including making good damaged/disturbed surfaces complete all as specified and directed. (Make: Jaquar Cat No. VGS-WHT-81853P180UF or equivelant of make as per list of manufacturer's) |
| 58 | S & F in repairs, Vitreous China wash basin, Table Top Basin, Size: 645 x 500 x 130mm excluding taps but including CP waste coupling, PVC waste pipe fixed on granite slab complete all as specified and directed.(Make : Jaquar Cat No. JDS-WHT-25943 or equivalent of make as per List of manufacturer's) |
| 59 | S & F in repairs Vitreous China urinal, with all Fixing Accessories Set, of Size: 355x340x535mm, Starwhite with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: Jaquar Cat No. URS-WHT-13261 or equivelant of make as per list of manufacturer's) |
| 60 | S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60gms) complete all as specified and directed. |
| 61 | S & F in repair 15 mm bore, push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm- 47gms)complete all as specified and directed. |
| 62 | S & F in repairs, 15 mm bore, Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms)complete all as specified and directed. |
| 63 | S & F in repairs, 15 mm bore, Bib tap fancy type of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm- 105gms)complete all as specified and directed. |
| 64 | S & F in repairs, 15 mm bore, Bib tap with long body of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm- 120gms)complete all as specified and directed. |
| 65 | S & F in repairs, 15 mm bore, Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight15mm-110gms) complete all as specified and directed. |
| 66 | S & F in repairs, 15 mm bore, Pillar taps fancy type of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight15mm-120gms) complete all as specified and directed. |
| 67 | S & F in repair Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms) complete all as specified and directed. |
| 68 | S & F in repair Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed. |
| 69 | S & F 20mm bore brass elbow complete all as specified and directed. |
| 70 | S & F 25mm bore brass elbow complete all as specified and directed. |
| 71 | S & F 20mm bore male brass threaded adaptor (MTA/ MBTA) complete all as specified and directed. |
| 72 | S & F 25mm bore male brass threaded adaptor (MTA/ MBTA) complete all as specified and directed. |
| 73 | S & F 20mm bore female brass threaded adaptor (MTA/ MBTA) complete all as specified and directed. |
| 74 | S & F 25mm bore female brass threaded adaptor (MTA/ MBTA) complete all as specified and directed. |
| 75 | S & F 20mm bore tank adaptor complete all as specified and directed. |
| 76 | S & F 25mm bore tank adaptor complete all as specified and directed. |
| 77 | S & F in repairs 15mm bore, bib taps, fancy type, long body with wall flange cast copper alloy, chromium plated with handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 78 | S & F in repairs 15mm bore, bib taps, fancy type, with wall flange cast copper alloy, chromium plated with handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 79 | S & F in repairs 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 80 | S & F in repairs, 15 mm bore, Stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 81 | S & F in repairs 15 mm bore, angle valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 82 | S & F in repairs, 15 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 83 | S & F in repairs, 20 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 84 | S & F in repairs, 25 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 85 | S & F 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed. |
| 86 | S & F 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed. |
| 87 | S & F in repair PVC over head tank cover suitable for 500 Litres capacity tank complete all as specified and directed. |
| 88 | S & F in repair PVC over head tank cover suitable for 1000 Litres capacity tank complete all as specified and directed. |
| 89 | S & F in repairs, 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed. |
| 90 | S & F in repairs, 25 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed. |
| 91 | M & L for Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 250 & n.exc 500 Ltrs and from mouths of circulating pipes, etc. \\"cleaning the tank by scrubbing the deposites with wire brush after draining out water from the tank and using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as \\"CLEANDED ON : DD.MM.YY\\", letter height exc 50mm and n.exc 100mm complete all as specified and directed. |
| 92 | M & L for Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 500 & n.exc 1000 Ltrs and from mouths of circulating pipes, etc. \\"cleaning the tank by scrubbing the deposites with wire brush after draining out water from the tank and using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as \\"CLEANDED ON : DD.MM.YY\\", letter height exc 50mm and n.exc 100mm complete all as specified and directed. |
| 93 | M & L for Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 1000 & n.exc 2000 Ltrs and from mouths of circulating pipes, etc. \\"cleaning the tank by scrubbing the deposites with wire brush after draining out water from the tank and using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as \\"CLEANDED ON : DD.MM.YY\\", letter height exc 50mm and n.exc 100mm complete all as specified and directed. |
| 94 | M & L for Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 2000 & n.exc 3000 Ltrs and from mouths of circulating pipes, etc. \\"cleaning the tank by scrubbing the deposites with wire brush after draining out water from the tank and using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as \\"CLEANDED ON : DD.MM.YY\\", letter height exc 50mm and n.exc 100mm complete all as specified and directed. |
| 95 | S & F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and SWG 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed. |
| 96 | S & F in repairs vitreous China wash down water closet pan (pedestal pattern), white, with PVC (SWR) 'P' or 'S' trap including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed. |
| 97 | S & F in repairs, plastic water closet, Seat and Cover for pedestal pan, white / black, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 98 | S & F in repairs 15 mm bore, Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook with N.R.V (Back Flow Preventer) with all accessories complete all as specified and directed. |
| 99 | S & F in repairs, Coloured, Toilet paper holder of vitreous china, box type fixed to wall with chromium plated brass screw complete all as specified and directed. |
| 100 | S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed. |
| 101 | S & F in repairs vitreous China wash basin, size 550 x 400mm, white, flat back, with PVC waste pipe, CP waste coupling, 32mm dia, chain, plug and porcelean stopper & backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and directed. |
| 102 | S & F in repairs 32mm bore bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms) complete all as specified and directed. |
| 103 | S & F in repairs, brass CP basin mixer for mixing hot & cold water screwed down for iron pipe and fixed, 15mm bore and fixed complete all as specified and directed |
| 104 | S & F in repairs, stainless steel kitchen sinks with drainage board made of 1 mm thick sheet for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 105 | S & F in repairs, Vitreous China urinal, half stall type, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. |
| 106 | S & F in repair 32 mm dia waste coupling of PTMT (Half or full threaded ) (Minimum Weight 45 grams) complete all as specified and directed. |
| 107 | S & F 32mm dia flexible PVC waste pipe, 800mm long for wash basin/sink etc complete all as specified and directed |
| 108 | S & F in repairs 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed. |
| 109 | S & F in repairs 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed. |
| 110 | S & F in repair 125 mm size, shower rose, with shower arm, brass chromium plated, swival type, complete all as specified and directed. |
| 111 | S & F in repairs, CP exposed wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe and fixed with connecting legs & wall flanges, complete all as specified and directed. |
| 112 | S & F in repair Soap dish of stadard size, brass chromium plated, fixed in walls with plugs & chromium plated brass screws complete all as specified and directed. |
| 113 | S & F in repairs 20 mm bore, Brass chromium plated, tubular towel rail, D type, 60 cm long between flanges with brackets complete all as specified and directed. |
| 114 | S & F in repairs, acrylic PVC bathroom cabinet of size 600 x 450x150 mm with openable shutter fixed with looking mirror of selected quality glass and with suitable shelves in side the cabinet of superior quality as approved complete all as specified and directed. |
| 115 | S & F in repair 600mmX450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromiun plated brass screws and cup washers complete all as specified and directed. |
| 116 | S & F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 117 | S & F in repair stainless steel Grating, 75mm dia fixed with white cement complete all as specified and as directed. |
| 118 | S & F in repair stainless steel Grating, 100mm dia fixed with white cement complete all as specified and as directed. |
| 119 | S & F in repairs, 75 mm bore, Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 120 | S & F in repairs, decorative wall paper fixed to wall ,complete all as specified and directed. Please Enable Macros to View BoQ information |
