|
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 20cm deep and getting out in soft/loose soil complete all as specified and as directed by engr in charge |
| 2 | Demolition of cement concrete in ground floors and pavings n. exc. 15 cm thick (below or above ground level) complete all as specified and as directed by engr in charge |
| 3 | M&L for broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by engr in charge |
| 4 | M&L for 100mm thick cement concrete type D- 2, 1:4:8 using (40mm graded stone aggregate) as in sub base complete all as specified and as directed by engr in charge |
| 5 | M&L for providing and laying 60mm thick factory made rubber moulded glossy finished chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as spd and as directed by engr in charge |
| 6 | Removal excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed by engr in charge |
| 7 | M&L for providing precast cement concrete apex stones / kerbs made of cement concrete type B-1 1:2:4 (using 20mm graded stone aggregates) set in cement mortar 1:4 complete all as specified and as directed by engr in charge |
| 8 | S&F for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by engr in charge. |
| 9 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft / loose soil complete all as specified and as directed by engr in charge |
| 10 | M&L for cement concrete type C-2 1:3:6 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete complete all as specified and as directed by engr in charge. |
| 11 | Excn in trenches n.exc 1.5m depth and wide for foundation n.exc 10 sqm on plan and getting out in soft / loose soil complete all as specified and as directed by engr in charge. |
| 12 | M&L for cement concrete type D2 1:4:8 (using 40mm graded stone aggregates) in foundation, filling and mass concrete complete all as specified and as directed by engr in charge. |
| 13 | M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed by engr in charge. |
| 14 | M&L for rendering 15mm thick on brick masonry surfaces in cement mortar 1:4, finished even and smooth w/o using extra cement complete all as specified and as directed by engr in charge. |
| 15 | M&L for cement concrete type B1 1:2:4 (using 20mm graded crushed stone aggregates),as in coping / kerb etc complete all as specified and as directed by engr in charge. |
| 16 | M/L for two coats of cement based paint over one coat of white wash on wall after preparation of new surface complete all as specified and as directed by engr in charge. |
| 17 | M&L for 100mm thick cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as in sub base complete all as specified and as directed by engr in charge. |
| 18 | M&L for 80mm thick rubber moulded coloured machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006, M-35 Grade over and including 25 mm thick sand cushion in patteerns with different colour paver block /tiles as in path, complete all as spd and as directed by Engr in charge |
| 19 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frame of Partition, doors, windows, ventilators with one or more rebates including joining cleat for fixing glazing clips, rubber packing aluminium map beading packing screws, poweder coated anodised alumiumum fittings etc gap of junction at top, bottom & sieds to be filled with silicone fillers/Neoprene felt etc complete all as specified and as directed by Engr-in-Charge |
| 20 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed by Engr in charge. |
| 21 | S & F for Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber/Aluminium frame work inclusive of necessary frame work / filleting to hold the plywood panels and joint sealed complete all as specified and as directed by Engr in charge. |
| 22 | S&F for 5.5mm thick plain glass, ordinary quality and glazing with oil putty/aluminium glazing clips in squares exc 0.5 Sqm in each panel complete all as spd and as directed by Engr in charge. |
| 23 | S&F 300mm long aluminium anodized sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed. |
| 24 | S&F, Aluminium(Die cast)body Door closer hydraulically regulated,designation No3,universal type,suitable for shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified & as directed by Engr in charge. |
| 25 | S & F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples all as specified and as directed by the Engineer-in-Charge |
| 26 | M&L 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in levelling course complete all as specified and as directed by Engr in charge. |
| 27 | M&L non skid cermic coloured tiles 8mm thick ( square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floor etc and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layer in CM (1:6) all as specified and directed |
| 28 | S&F glazed ceramic coloured tiles in vertical surfaces/dado/skirting on wall 350 x 250 x 7mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl cutting to reqd shape and size over and including 10mm thick plaster in CM (1:4) on vertical surfaces as backing coat complete all as spd and as directed by Engr in charge |
| 29 | Taking down chowkats or frames with shutters w/o taking off shutters from the frames n.exc 1.5 Sqm each,complete all as specified and as directed. |
| 30 | Taking down chowkats or frames with shutters) w/o taking off shutters from the frames exc 1.5 Sqm and n.exc 4.0 sqm each each, complete all as specified and as directed. |
| 31 | Taking down cement plaster any descriptionfrom walls/ceiling including racking out joints hacking for key scrubbing down with water etc. |
| 32 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick plaster of paris putty over a coat of primer using roller only as per manufacturers instruction, complete all as specified and as directed. |
| 33 | M&L for complete removal of existing surface and preparation of plastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick plaster of paris putty over a coat of primer using roller only as per manufacturers instruction, complete all as specified and as directed. Please Enable Macros to View BoQ information |
