|
| 1 | Dismantling asbestos cement sheet, ridge (corrugated, semicorrugated, plain etc.) in roof covering,wall etc or of similar types complete all as specified and directed. |
| 2 | Dismantling of timber scantlings 40 sqcm & over in section framed work complete all as specified and directed. |
| 3 | Taking down chowkhats or frames with shutters without taking off shutters from the frames not exceeding 1.5 Sqm each complete all as specified and directed. |
| 4 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4 sqm each, complete in all respect as specified and directed. |
| 5 | Demolition of cement concrete (unreinforced) in ground floors of any description (below or above ground level) complete all as specified and directed. |
| 6 | Taking down cement plaster of any thickness and description on brick/concrete/stone walls, ceilings, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 7 | Taking down plastering on lathing (other than wire-netting), without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered complete all as specified and directed. |
| 8 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and directed. |
| 9 | Dismantling wooden weather boarding of any description fixed in any position with nails/ screws complete all as specified and directed. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish offt the premises complete all as specified and directed. |
| 11 | S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws alongwith bitumen washer complete all as specified and directed. |
| 12 | S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strength of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws alongwith bitumen washer complete all as specified and directed.Note- The measurement shall be carried out as in a plain sheet. |
| 13 | S&F coloured 0.50mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet having tensile strength of 550 Mpa as in eves board/ covering or of similar type, fixed with self tapping screws alongwith bitumen washer fixed over mild steel flats, angles etc fixed with framed structure complete all as specified and directed. |
| 14 | S & F plate girder or single stanchions, built up of one beam or channel section with flange plates, caps bases, splices, agnle brackets cleats and other connection confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. |
| 15 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality \\"A\\") including necessary welding complete complete all as specified and directed. |
| 16 | S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 2mm dia GI wire as suspender and including 3.5-4mm thick decorative, pre -painted, non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantaling of existing false ceiling complete in all respect as specified and directed. |
| 17 | S & F for Factory made single extruded WPC (wood polymer composite) solid door/ window / ceosetory windows & other frames / chowkhat of size 65x150 mm comprising of virgin PVC polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers (wood power / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having maximum frame density of 750 kg / cum, screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum comprssive strength of 58 N / mm², Modules of elasticity 900 N / mm² and resistance to spread of flame of class A category with property of beeing termite / borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast / lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast / lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 18 | S&F 35mm thick Flush shutters, solid core construction, with block board core with decorative face veneers with lipping on both sides, complete in all respect as specified and directed. |
| 19 | Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panel door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 20 | S&F mild steel work such as in guard bars, grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; and of similar type of work conforming to Fe 290, Gde-E-165 complete all as specified and directed. |
| 21 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixing with beads in door/window/ventilator/fixed glazing shutters complete all as specified and directed. |
| 22 | S&F 150mm length of bolt, Aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed. |
| 23 | S&F 150 mm size, Aluminium handle cast type anodised complete all as specified and directed. |
| 24 | S&F aluminium anodised sliding door bolts with hasp and staple (boil type) 19mm dia bolt 300 mm long complete all as specified and directed. |
| 25 | S&F 100mm size mild steel butt hinges complete all as specified and directed. |
| 26 | M&L for preparation of new undecorated steel surfaces with pre mixed steel filler used as putty for steel work and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer before painting complete all as specified and directed. |
| 27 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coat of white putty and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of new decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. |
| 28 | M&L for applying two coat interior 100% anti fungal acrylic smooth emulsion with silicon additives on new plastered surfaces that offer anti alge high performance interior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 29 | M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 30 | M&L for half brick work with sub class 'B' bricks, old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantaling of brick work built in cement mortar in any position complete in all respect as specified and directed. |
| 31 | M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:4) finished even and smooth without using extra cement complete in all respect as specifified and directed. |
| 32 | M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:6) finished even and smooth without using extra cement complete in all respect as specifified and directed. |
| 33 | S & F 10mm dia and over TMT bar cut to length bent to shape required, including cranking, bending spiarlly for hooping for colums, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete in all respect as specified and directed. |
| 34 | S & F upto 10mm dia TMT bar cut to length bent to shape required, including cranking, bending spiarlly for hooping for colums, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips for stirrups, spacers and binders complete in all respect as specified and directed. |
| 35 | Providing and laying reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in beams, lintels, etc complete all as specified and directed. |
| 36 | M&L for formwork to sides and soffits of floor or roof beams, beam haunchings,girders,bressummers,lintels, cantilevers,shelves including supports, overhangs, etc. also splays between floors and beams, etc. in rough finished flat surface of concrete complete all as specified and directed. |
| 37 | Providing and laying 40mm thick of cement concrete using type B-1, (1:2:4) (using 20mm nominal size crushed and graded stone aggregate) flooring and finished even and smooth using extra cement complete in all respect as specifified and directed. |
| 38 | Providing and laying of 75mm thick cement concrete, using type C-1, (1:3:6) (using 20mm nominal size crushed and graded stone aggregate), laid in alternate penals/bays and finished the surafce even and smooth without using extra cement complete in all respect as specifified and directed. |
| 39 | Forming Contration (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound (1 part of bitument and 3 part of sand) complete in all respect as specifified and directed. |
| 40 | Providing and laying cement concrete in coping, hold fasts, using type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form work etc. complete in all respect as specifified and directed. |
| 41 | S & F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete in all respect as specifified and directed. |
| 42 | Roughening of surfaces of old concrete floor by picking, sweeping clean, and washing down with water to remove dust, etc. complete all as specified & directed. |
| 43 | M&L for Brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified & directed. |
| 44 | Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed. |
| 45 | Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skriting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. |
| 46 | S & F PVC coloured insulated over MS pipe 20mm dia curtain rod with fixing bracket, stops, rollers etc. complete in all respect as specified and directed |
| 47 | Providing and fixing of full length mirror of size 400X1500 made of 5.5 mm thick superior quality float glass mirror conforming to relevant IS standards, with beveled edges fixed on wall with SS mirror screws with decorative caps including aluminium channel backing necessary wall plugs, screws and making good the disturbed surfaces complete in all respect as directed by Engineer-in-charge. |
| 48 | Providing and fixing factory made uPVC colour casement windows & ventilator (Outward /inward) with hinges system made of extruded profiles. Profiles of frames 60mm X 58mm and sash (style and rail) 60mm X 78 mm will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware, EPDM gasket, 1.2+0.2.mm thick galvanized steel profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, all complete and as directed, (Glazing, hardware hinges and fitting, EPDM rubber gasketetc. to be paid separately.)Note:-Each member of window to be measured separately with clear length. |
| 49 | Providing and fixing factory made uPVC colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket.1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.)(A) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each |
| 50 | Providing and fixing factory made uPVC colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket.1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of SS wiremesh and includes all other connected accessories Net opening will be measured for payment purpose.)(A) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each |
| 51 | S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed. |
| 52 | M&L for any colour of granite stone without white spots Granite stone slab 17 to 19 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed. |
| 53 | Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed. |
| 54 | Providing and injecting chemical emulsion for Post Construction Antitermite Treatment alongth the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. |
| 55 | Providing and injecting chemical emulsion for Post Construction Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 56 | S & F for coloured rubber moulded, glazed pre coated chequered cement concrete tiles of any shape and size 20-25mm thick with grey cement with pigment,; set jointed and pointed in neat cement slurry with pigment in floors including over 15mm thick screed bed in CM 1:4 complete in all respect as specified and directed. Sample as approved by GE. |
| 57 | Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point ,socket point or power point including fixture and fitting such as switches , ceiling roses, pendants , regulators , sockets , light fitting etc. removing material to store for keeping in safe custody or for taking credit( credit for above items should be made as per conditions seperately) and making good the disturbed surfaces of wall/floor or ceiling to match with existing surface and finishing the surfaces with distemper/white washing/colour washing as per existing complete all as specified and directed. |
| 58 | Taking down carefully by unscrewing from main switch boards/cut out boxes/MCB DBs / complete sealing the cable end and making good disturbed surface by walls etc. |
| 59 | Taking down carefully (copper/aluminum) unsv sub main wiring complete of any type (batten/surface conduit or concealed) complete for taking credit and making good the disturbed surfaces of wall/floor or ceiling to match with existing surface and finishing the surfaces with distemper/white washing/colour washing as per existing complete all as specified and directed. |
| 60 | Taking down ceiling fan of any type and size and keep in safe custody and deposite to MES store yard complete all as specified and as directed by Engineer-in-charge. |
| 61 | M & L for Point wiring for one light point controlled by one switch with 1.5 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded copper cable confirming to IS:694(2010) using approved colour code for phase and neutral as per IS code drawn through non metallic PVC rigid concealed conduit heavy mechanical stress (HMS) grade in accordance with IS:9537 (Part 3) having wall thickness not less than 2.0 mm thick and minimum 20 mm external dia but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I (ISI marked) including conduit accessories like bends, tees, junction boxes etc fixed concealed with all accessories suitable for modular type fitment,provision for fixing of modular flush boxes of appropriate sizeand dimensions for fixing of piano switches/sockets/regulator etc including PVC insulated and unsheathed FRLSH 1.5 sqmm multi stranded copper conductor cable (green color) as continous earth lead wire connected to common earth and earth dolly complete all as specified and directed by Engr-in-Charge. Make of Wire : Havells/RR Kabel/FinolexMake of Coduit : Anchor/Precision/Astral |
| 62 | Description all as per item No.61 above but for ceiling fan / Exhaust fan point controlled by one 5 amp switch |
| 63 | Description all as per ser item No 61 but for 05 amp socket outlets point controlled by one switch on Independent board complete all as specified and directed. |
| 64 | Description all as per ser item No 61 but for 05 amp socket outlets point controlled by one switch on same board with other switches complete all as specified and directed. |
| 65 | Description all as per ser item No 61 but for 15 amp socket outlets point controlled by one switch on Independent socket outlet using 2.5sqmm PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded copper cable confirming to IS:694(2010) using approved colour code for phase and neutral as per IS code as per IS code drawn through non metallic PVC rigid concealed conduit heavy mechanical stress (HMS) grade in accordance with IS:9537 (Part 3) having wall thickness not less than 2.0 mm thick and minimum 20 mm external dia but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I (ISI marked) including conduit accessories like bends, tees, junction boxes etc fixed concealed with all accessories suitable for modular type fitment,provision for fixing of modular flush boxes of appropriate size and dimensions for fixing of piano switches/sockets/regulator etc including PVC insulated and unsheathed FRLSH 2.5 sqmm multi stranded copper conductor cable (green color) as continous earth lead wire connected to common earth and earth dolly complete all as specified and directed by Engr-in-Charge. Make of Wire : Havells/RR Kabel/FinolexMake of Coduit : Anchor/Precision/Astral |
| 66 | M&L for Ceiling rose ceiling rose , 2 to 3 terminal PVC/ polycarbonate , isolated body type suitable for AC 230 volts complete all as specified. |
| 67 | M & L for module cover plate with frame as per site requirement for following module complete all as specified and as directed. |
| 68 | 1 module |
| 69 | 2 module |
| 70 | 3 module |
| 71 | 4 module |
| 72 | 6 module |
| 73 | 8 module |
| 74 | M & L for Modular metal Flush box as per site requirement. |
| 75 | 1/2 module |
| 76 | 3 module |
| 77 | 4 module |
| 78 | 6 module |
| 79 | 8 module |
| 80 | M & L for modular switch 1 way 5/6 Amp 1 Module, 240 volts complete all as specified and as directed.Make : Legrand/Crabtree/Anchor Roma |
| 81 | M & L for Modular Switch 1 way 16/20 Amp 1 Module, 240 volts complete all as specified and as directed.Make : Legrand/Crabtree/Anchor Roma |
| 82 | M &L for Modular Socket 6A 2/3 Pin universal 2 module , complete all as specified and as directed.Make : Legrand/Crabtree/Anchor Roma |
| 83 | M &L for Modular Socket 16A/ 6A 2/3 Pin combined 2 module ,complete all as specified and as directed.Make : Legrand/Crabtree/Anchor Roma |
| 84 | M &L for Modular fan step regulator 120 watt 2 module ,complete all as specified and as directed.Make : Legrand/Crabtree/Anchor Roma |
| 85 | Supply and fix Lamp holder, white Polycarbonate body, with back plate suitable for batten/bulb fittings fixed in position & connecting complete. |
| 86 | Supply and fix emergency inverter built LED lamp 10/12 watt cap ,lumen output not less than 1100 lumen estimated life span of 25,000 hrs ,IP 20,CRI-80, B22/E27/E14 complete all as specified and directed. Make : Philips/Havells/Jaquar |
| 87 | S&F energy efficient 20 watt (4.0 feet) LED integrated batten type luminaires suitable for wall or ceiling mounting with built in LED Chip & integral LED driver 20 watt,Aluminium channel housing & Polycarbonate diffuser of length 1200 mm (approx.),Color temperature 6500 K or as directed, CRI between 80-85, Low THD, PF-0.90 (mimium), IP-20, efficacy not less than 120 lumen/watt or total lumen output not less than 2400 lumen per 20 watt, operating range 200-270V, surge protection of 2 kV, over voltage protection and other safety tests as per IS 15885 Part-2/Part-3, estimated life span of 25,000 hrs with all accessories, complete with fixing arrangement, fitting shall be internally prewired and conforming to LM 79 & LM 80 standard, making all connection using 1.5 sqmm copper conductor multistrand PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete fixed in position & connecting complete all as specified and directed by Engr–in-charge. Note:(i) LED fitting shall be provided for 3 years warranty. Make : Philips/Havells/Jaquar |
| 88 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make : Philips/Havells/Jaquar |
| 89 | Supply and fix LED bulkhead luminaire in die-cast aluminium alloy body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection suitable for and including provision of 10W retrofit LED bulb, full white with B22 lamp holder, complete all as specified and directed. Make : Philips/Havells/Jaquar |
| 90 | Supply and fixing 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, down rod/down rod as per height available at site, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.0, Air delivery minimum 210 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply etc, complete with fixing arrangement anchor tpe fastener hook including connection with 1.5 sqmm mutistrand copper conductor flexible wire from ceiling rose to fan drawn through PVC flexible conduit complete all as specified and directed. |
| 91 | Supply and Fix distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 8 way with appropriate Amps rated copper busbar, neutral bar,internal earth bar and cable ties for cable management, reversible door forIP 43 & IP 54, IK 09 impact resistance, single pole and neutral 250 Volts, flush to wall including chases cutting in wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.DB shall be designed with provision for MCB SPN as incomer & MCB SP as outgoing as per requirement. Cost of the DBs will be without MCBs complete all as specified and as directed Note - Rates are inclusive for flush(Concealed ) mounting of DB SPN.Make: Legrand/Schneider/ABBNote : The MCB shall be of same make as per distribution board |
| 92 | Supply and fixing 240V,10 KA 'C' curve miniature circuit breaker (MCB) single pole of current carrying capacity 6 to 32 AMP, in the MCB DB complete with connection testing and commissioning all as specified and directed. |
| 93 | Supply and fixing 240V,10 KA 'C' curve miniature circuit breaker (MCB) single pole of current carrying capacity 40 Amps, in the MCB DB complete with connection testing and commissioning all as specified and directed. |
| 94 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral and current carrying capacity 32 Amps, in the MCB DB complete with connection testing and commissioning all as specified and directed. |
| 95 | M & L for Earthing complete with GI earth electrode plate of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to GI wire 4mm dia as earth lead up to test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates, 40mm thick precast RCC cover in 1:2:4 reinforced with expanded metal (weight not less than 4 kg/sqm), and frame of angle iron 25x25x6mm with lugs 02 nos with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including light grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI earth wire protection pipe 15mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I, connected to earthing testing point and testing on completion complete all as specified and directed by Engr-in-charge. |
| 96 | M & L for GI wire 4mm dia and fixing with proper clamp,saddles,nuts bolts,washers etc. properly and connected to pole complete all as specified and directed. |
| 97 | S & F GI Pipe light grade 15mm bore for protection of GI earth lead complete with all fittings all as specified and as directed |
| 98 | S & F LED building security Light fitting 35 watt, for opearting voltage between 110V to 320V system efficiency not less than 120 lumen / watt, PF-0.95 minimum, IP66 protection, 5700CCT(K), CRI between 80-85, confirming to LM79 and LM 80 standards or as per IS-16104:2012 and IS-16106:2012, for estimated life span of minimum 50,000 hrs consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with LED street optics LENS for uniform light distribution, weather proof gasket for lamp & driver compartment, Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws with IP 65/66 protection, complete all as specified and as directed by Engr-in-charge. Make : Philips/Havells/Jaquar |
| 99 | Supply & Fixing Bracket made out of GI light grade pipe of size 40 mm dia 1.5 mtr long bend to an angle of 120 degree with 02 Nos MS clamp 50mm x 50mm and 04 sets of nuts,bolts and washers painting with two coats of synthetic enamel paint over a red oxide primer complete all as specified and as directed by Engr-in-charge. |
| 100 | M&L Sub main wiring using PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded copper cable confirming to IS:694(2010) using approved colour code for phase and neutral as per IS code drawn through non metallic PVC rigid concealed conduit heavy mechanical stress (HMS) grade in accordance with IS:9537 (Part 3) having wall thickness not less than 2.0 mm thick and external dia as under but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I ( ISI marked) including conduit accessories like bends, tees, junction boxes etc fixed concealed with all accessories complete all as specified and as directed by Engr-in-charge of the following sizes of cables as under . Note:Rate of sub main wiring shall include cutting chases for conduit/flush boxes etc Make of Wire : Havells/RR Kabel/FinolexMake of Coduit : Anchor/Precision/Astral Note: Using two single core PVC insulated FRLS cable 6.0 sqmm copper conductor multi stranded and 6.0 sqmm copper conductor insulated cable using as earth wire Note :2runs of 6sqmm copper cable & 1 run of 6.0 sqmm copper cable in and including PVC conduit 25mm shall be measured as one unit |
| 101 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out in any type soil for laying pipes, cables etc complete all as specified and directed by Engineer-in-Charge. |
| 102 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed by Engineer-in-Charge. |
| 103 | Removing excavated surplus material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 104 | Supply and spreading fine river sand in trenches for cushioning of under ground cable/filling cable ducts complete all as specified and as directed by Engr-in-Charge at site. Note : Only punned thickness shall be measured for payment purpose |
| 105 | Supply and laying burnt brick sub class ‘B’ of standard size laid in trenches as protection to cables complete all as specified and as directed by Engineer-in-charge. |
| 106 | M & L for boring of holes under road, pavement, hard standing by trenchless technology technique for 40-80 mm dia pipe complete all as specified and as directed by Engineer-in-charge. |
| 107 | M & L for light grade galvanized pipe ISI marked laid in trenches, under road or fixing on wall/pole/ crossing nallah etc for cable protection of bore 40 mm complete all as specified and as directed by Engineer-in-charge. |
| 108 | Supply, laying and testing, commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100 Volt grade on walls with fixing acessories, of 16 Sqmm, 2 core including taking down existing cable/ service wire of any size complete all as specified and directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
