|
| 1 | Dismentiling old plaster and pointing in cement or lime and raking out joint of 15 mm depth waterring and disposal of unservisable material with all lead as per direction of E/I |
| 2 | Providing 12mm thk. Cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 3 | Providing 6mm thk. Cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water,scaffolding, taxes and royalty all complete as per builing specification and direction of E/I. |
| 4 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.1 Double charge vitrified tile polished finish of size11.41A.1.3 Size of Tile 600 x 1200 mm |
| 5 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, inskirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigmentsetc. complete. |
| 6 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete |
| 7 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 8 | Providing and laying 25mm. thick kotah stone tiles in risersof steps, skiiting and pillars of approves size, texture and colour laid cover 12mrn. thick cement mortar (1:3) and.loined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolilthic finish with approved quality of carborandurn stone including cost of curing, taxes and royaliy all complete as per building specificationand direction of El. |
| 9 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 10 | Providing two coats of plastic emulsion paint of approved shade & make over a coat of cement primer on new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty whereever required, scafffolding, washing of floors & taxes all complete as per building specification and direction of E/I |
| 11 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat ofexterior primer applied @ 2.20 kg/10 sqm) |
| 12 | Taking down old door & window shutters including staking searvisable matarial within 15m lead and disposal of unservisable material with all lead as per direction of E/I |
| 13 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 14 | Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 15 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 16 | Labour for scrapping old paint with paint remover and below lamp as required on wooden or steel surface including cost of all labour and materials end scaffolding all complete as per bulding specification and direction of E/l |
| 17 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning.removing dust,dirt,scales smokes and grease and cleaning the surface thoroughly including cost of scatfolding and taxes all comiplete as per building specification and direction ot E/l. |
| 18 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 19 | Waterproofing for Old and New Roof Stab Providing and laying water roofing treatment on roaf slab by applying two Componenae Aeegredready ta use, acrylic tmoditted Waxible materigl applied win Sroler or spray tor water proofing.coating es per menur fácurer MAR SCHED SRedficathahs with followirig stepe surface pteparalionProdiig and cieaniog of concrete sutace emovedust, ol grease pcluding removal of existihg loasé pant ating, and cement taltancaby clethng wits compraseed air & waterjetst ding almatertals, tabour, toolsotmplete.Ponding leet to be donea ANN pluooir9.al cutets andtee checkedtron.softiderity seepageaoe On dentifcaipn oreepape, ce men grogto ba döne with on shrink expandmg admixtaureof sike tnaia PvLtd, FMYK Schomberg DFiRUFosToeor equivalent Providing-and reparing of ecorners and joiots suchas those between the paraper walt and the roof siab ete sha be chemfered wa 50mm 150 mm fillet of martar (Cement: and 4admxewih acrylic polymer of SikalFosroe/MYK Schomberg/Dr Ft of eguivalent. Before chamfering a prime èeoat shall be given witn the slurry of aCyic polymer. Repalring surface iregutarites, damaged concretainbase slab dead cracks if any, with an acrylic polymer modifiedirepair.mortar tncluding a coat of bonding agent of the same with cement slufry including all material, Jabour, tools complete. (6)1st Coat-Apply 1st use, coat of two component acrylic modifiad, reedy to fexibte cemenitious matérlal on surface saturated dry roof and inside walloParapet wall upto 600 mm by brush or roler After 1st of coat application, 45 gsm of Fibre glass cloth to lay when the stH green. first tayer is 1st.coat should be applied @1.50 kg/Sqmt/coat. For purpose the of measurement the entre (c) 2nd Coat-To treated.surface will be measured apply the 2nd coat of two ready component acrylic modified, to use, flexible cementtious material right over the angle to the st coat glass fibre laid surace. 2nd coat shoud be Sqmt/coat. For the [email protected] kg! purpose of measurement the wll be measured. entire reated surface After three days ofdrying the 2nd coat water outlets to be , the rain plugged and \ identify ponding test to be done for 48 hours to seepage, leakage from soffit and if found necessary rectfication to be done as per salisfaction of Elc. protected from damage before screed over it. Water Sika Topseal 109hl Fosroc Brushbond proofing Brand: RFX Dr Fixtt Pidiffin 2K/MYK The waterproof coating to be Product Performance- Chemical Base Part A: Aquafin TGG Acrylic copolymer, Part B: Specially graded cemenitious Density 1.6 kgA (mixed density) at +27°C powder 2 NVmm2 after 28 days (with Fibre cloth) (According to ASTMD Pullout Bond Strength 2370) -2 Nmm2 (concrete failure) (Accord |
| 20 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames einforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge9.117.1 Extruded section profile size 48x40 mm |
| 21 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (±0.2 mm) with inbuilt edging on both sides. The styles and rails mitredand joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filledwith a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 22 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. |
| 23 | Wiring for light point/fanpoint/exhaust fan point/call bell point with 1.5 sq.mm FRPVC insulated copper conductors in glecorecable in surface/recessed PVC conduit,with modular types witch,modular plate,suitable size of GI box etc as required. |
| 24 | S/F Modular type electronic fan regulator :-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc asrequired. |
| 25 | S/F Ceiling Rose :- |
| 26 | Supply, fitting, fixing and testing of 1200mm Sweep, double ball-bearing, 2 canopy ceiling fan including connection with 1.5 sq mm copper wire, down rod all accessories as required. |
| 27 | Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required. |
| 28 | Supplying and fixing batten/ angle holder including connection etc. as required. |
| 29 | 15/16 Watt LED Bulb |
| 30 | Supplying, fitting and fixing 40mm high vitreous white glazed ware E.W.C. with \\"p\\" trap of parry/hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make and complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle cock of approved qualty weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and White/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide prining, all complete as per specification and direction of E/I. |
| 31 | Supplying fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of Hindustan \\"Parry\\" or any other approved ISS make with 5 liters capacity C.I. automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams 15 mm P.V.C /Alkthene pipe 450 mm long with bras coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor, making good the same etc all complete as per specification and direction of E/I . |
| 32 | Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I |
| 33 | Supplying, fitting and fixing H.C.I. pipes with ear of approved make conforming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yarn for making lead caulked joints, cutting pipes to size including earth woek or scaffolding where necessary etc. all complete as per specification and direction of E/I. 100mm dia |
| 34 | 75 mm dia |
| 35 | Supplying and fixing H.C.I. fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earthwork or providing scaffolding as the case may be all complete as per specification and direction of E/I.H.C.I. Heal Rest bend. 100 mm dia (wt. 5.5 kg. app) |
| 36 | 80 mm dia (wt. 4 kg. app) |
| 37 | H.C.I. double junction with door and ear.100 mm dia (wt. 15.5 kg. app) |
| 38 | 80 mm dia (wt. 15.5 kg. app) |
| 39 | Floor trap with grating. 100mm dia |
| 40 | Norton patent H.C.I. Cowel. 100mm dia (wt. 3.25 Kg appx.) |
| 41 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter |
| 42 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 43 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single pushfit Coupler.110 mm dia |
| 44 | Single tee with door. 110x110x110 mm |
| 45 | Bend 87.5°. 110 mm bend |
| 46 | Shoe (Plain) |
| 47 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 48 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 49 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes |
| 50 | 32 mm nominal dia Pipes |
| 51 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :100 mm diameter S.W. pipe |
| 52 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore |
| 53 | 25 mm nominal bore |
| 54 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 55 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:With common burnt clay F.P.S. (non modular) 100x100 mm size P type bricks of class designation 7.5 |
| 56 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:Brass stop cock |
| 57 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 58 | Carraige of materials (i) cement |
| 59 | (ii) sand |
| 60 | Add 18% for G.S.T. |
| 61 | Labour Cess Please Enable Macros to View BoQ information |
