Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Providing & fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting & making good the walls wherever required(Hindware/Cera/Parryware or eqivalvalent make) White Vitreous China wash basin 630 x450mm with a single 15mm C.P. brass pillar taps complete job. |
| 2 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including paintingof fittings and brackets, cutting and making good the walls wherever required (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 3 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. (Hindware/Cera/Parryware or eqivalvalent make) |
| 4 | Providing and fixing white vitreous china water closet squatting pan (Indian type) Orrisa pattern size 580 x 440 mm (Hindware/ Cera/ Parryware or eqivalvalent make)complete job. |
| 5 | Providing & fixing white vitreous china pedestal type (European type/ wash down type) water closet pan (Hindware/Cera/Parryware or eqivalvalent make)complete job. |
| 6 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid. |
| 7 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre capacity-White complete job. Hindware/Cera/ Parryware or eqivalvalent make) |
| 8 | Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 liter capacity -White |
| 9 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete semi rigid pipe 32 mm dia |
| 10 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required . Kitchen sink without drain 610 x 510 mm with bowl depth 200 mm |
| 11 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350mm and 340 x 410 x 265mm sizes respectively with automatic flushing cistern with CI/MS brackets standard size of G.I. flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete including painting of fitting and brackets, cutting & making goods the walls & floors wherever required. One urinal basin with 5 litre P.V.C. automatic flushing of approved quality |
| 12 | Providing and placing on terrace (at all floor levels ) polythylene Water Storage Tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for intlet, outlet and overflow pipes but without fitting and the base support for tank (Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ) |
| 13 | Providing and fixing 600 x 450 beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 14 | Providing & fixing unplasticised P.V.C. connection pipe with brass union 30 cm length 15mm nominal bore |
| 15 | Providing & fixing C.P. brass shower rose with 15 mm or 20 mm inlet 150mm diameter complete job. |
| 16 | Providing and fixing C.P hand spray with lever control (health faucet) and flexible hose 1 mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-In-charge |
| 17 | Providing & fixing G.I. pipes complete with G.I. fitting and clamps including cutting and making good the walls etc.Internal Work-Exposed on wall |
| 18 | 15mm nominal bore Medium |
| 19 | 20mm nominal bore Medium |
| 20 | 25mm nominal bore Medium |
| 21 | Providing & fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc complete |
| 22 | 15mm nominal bore Medium |
| 23 | 20mm nominal bore Medium |
| 24 | 25mm nominal bore Medium |
| 25 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing |
| 26 | 20mm nominal outer dia pipes. |
| 27 | 25mm nominal outer dia pipes |
| 28 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. |
| 29 | 20mm nominal outer dia pipes. |
| 30 | 25mm nominal outer dia pipes. |
| 31 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes |
| 32 | 75mm dia |
| 33 | 110 mm dia |
| 34 | 150 mm dia |
| 35 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/ accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansio |
| 36 | 75mm dia Plain bend |
| 37 | 110 mm dia Plain bend |
| 38 | Providing and fixing15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 |
| 39 | Providing and fixing15 mm dia nominal bore C.P. brass long nose bib cock of approved conforming to IS standards and weighing not less than 810 gms |
| 40 | Providing and fixing 15 mm nominal bore C.P. brass bib cock ofapproved quality conforming to IS : 8931 |
| 41 | Providing & fixing 15mm nominal bore C.P. brass angle valve for basin mixer and gyser points of approved for conforming to IS : 8931 |
| 42 | Providing & fixing 15mm nominal bore Plastic bib cock |
| 43 | Providing & fixing 15mm nominal bore Plastic Angle Valve |
| 44 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete |
| 45 | 15mm nominal bore |
| 46 | 20mm nominal bore |
| 47 | 25mm nominal bore |
| 48 | Supplying of Following Sanitary and Water Supply fittings:- |
| 49 | Inner face of approved quality |
| 50 | Disk face of approved quality |
| 51 | Jet of approved quality |
| 52 | Pillar Cock brass of approved quality |
| 53 | G.I Elbow 15mm of approved quality |
| 54 | G.I Elbow 20mm of approved quality |
| 55 | G.I Elbow 25mm of approved quality |
| 56 | G.I Socket 15mm of approved quality |
| 57 | G.I Socket 20mm of approved quality |
| 58 | G.I Socket 25mm of approved quality |
| 59 | G.I Tee 15mm of approved quality |
| 60 | G.I Tee 20mm of approved quality |
| 61 | G.I Tee 25mm of approved quality |
| 62 | G.I Reducer 15mmx 20mm of approved quality |
| 63 | G.I Reducer 25mmx 20mm of approved quality |
| 64 | G.I Reducer 15mmx 25mm of approved quality |
| 65 | G.I Elbow 15mmx20mm of approved quality |
| 66 | G.I Elbow 20mmx25mm of approved quality |
| 67 | G.I. Elbow 25mmx15mm of approved quality |
| 68 | G.I. Nipple 15x 50mm of approved quality |
| 69 | G.I. Nipple 15x 100mm of approved quality |
| 70 | G.I. Nipple 15x150mm of approved quality |
| 71 | G.I. Nipple 20 x 50mm of approved quality |
| 72 | G.I. Nipple 20x 100mm of approved quality |
| 73 | G.I. Nipple 20x 150mm of approved quality |
| 74 | G.I. Nipple 25x50mm of approved quality |
| 75 | G.I. Nipple 25x100mm of approved quality |
| 76 | G.I. Nipple 25x150mm of approved quality |
| 77 | White Cement 1 Kg pack of approved quality |
| 78 | Cistern Syphon of approved quality |
| 79 | Cistern Handle of approved quality |
| 80 | Cistern Vassel of approved quality |
| 81 | W.C. Seat Cover White/Coloured of approved quality |
| 82 | C.P. Nipple of approved quality |
| 83 | C.P. Grating of approved quality |
| 84 | C.P. Cup of approved quality |
| 85 | Towel Rod of approved quality |
| 86 | Towel Ring of approved quality |
| 87 | PVC Collar 75mm,100mm of approved quality |
| 88 | P.V.C Floor Trap of approved quality |
| 89 | P.V.C Tee of approved quality |
| 90 | G.I Check Valve of approved quality |
| 91 | P.V.C Cistern ball Cock of approved quality |
| 92 | Float Valve brass of approved quality |
| 93 | Tank Nipple of approved quality 25 mm , 20 mm |
| 94 | Waste Coupling of approved quality |
| 95 | C.P Soap Dish of approved quality |
| 96 | CPVC Union 20mm of approved quality |
| 97 | CPVC Union 25mm of approved quality |
| 98 | CPVC Ball Valve 20mm of approved quality |
| 99 | CPVC Ball Valve 25mm of approved quality |
| 100 | CPVC Brass MTA 20x15mm of approved quality |
| 101 | CPVC Brass MTA 20x20mm of approved quality |
| 102 | CPVC Brass MTA 20x25mm of approved quality |
| 103 | CPVC Brass FTA 20x15mm of approved quality |
| 104 | CPVC Brass FTA 20x20mm of approved quality |
| 105 | CPVC Brass FTA 20x25mm of approved quality |
| 106 | C.P Wall Mixer of approved quality |
| 107 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete |
| 108 | 100 x 10 mm |
| 109 | 150 x 10 mm |
| 110 | 200 x 10 mm |
| 111 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete |
| 112 | 100mm |
| 113 | 125mm |
| 114 | Providing & fixing aluminum sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to req. colour or shade with nuts & screws etc. complete: |
| 115 | 300 x 16mm. |
| 116 | 250 x 16mm. |
| 117 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Twin rubber stopper |
| 118 | Door closer Spring Type of approved quality |
| 119 | Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete : |
| 120 | Renewing Glass panes and refixing existing wooden fillets Float Glass Panes of thickness 4.0 mm (weight not less than 10 kg/ sqm) |
| 121 | Renewing Glass panes, with Putty & Nails wherever necessary float Glass Panes of thickness 4 mm (weight not less than 10 kg/ sqm) |
| 122 | Butt Hinges 3\\" of approved quality |
| 123 | Butt Hinges 4\\" of approved quality |
| 124 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material in cement mortar, all leads & lifts. |
| 125 | Demolishing cement concrete 1 : 3 : 6 or richer mix manually/ by mechanical means including disposal of material, all leads & lifts. |
| 126 | Demolishing RCC work manually /by mechanical means including stacking of steel bars and disposal of unserviceable material ,all leads & lifts. |
| 127 | Demolishing mud phaska in terracing and disposal of material including all leads & lifts. |
| 128 | Demolishing brick tile covering in terracing including stacking of serviceable material & disposal of unserviceable material including all leads & lifts. |
| 129 | Providing and laying in situ seven course water proofing treatment with APP (Atactic poly- propylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/ sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS: 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane of specified thickness, weight and centre core, HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement:3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement: 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately.) Modified Polymeric membrane 2.0 mm thick of 3.0 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron |
| 130 | Painting top of roofs with bitumen of approved quality at 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm incl. cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete with residual type petroleum bitumen of grade VG-10. |
| 131 | 10 cm thick mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35 kg/cum of earth and gobri leaping with mix 1 : 1 ( 1 clay : 1 cow dung) and covered with flat tile bricks of class designation 100 grouted with cement mortar 1:3 mixed with 2% of integral water proofing compound by weight of cement & finished neat with common burnt clay (non modular) brick tile of class designation 10.0 incl. all leads, lifts & carriage of material by MT/ H.L. |
| 132 | Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc consisting of following operations. a) Applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer in- charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge.d) finishing the surface with 20mm thick joint less cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineerin- charge.With average thickness of 120mm and minimum thickness at khurra as 65 mm |
| 133 | Providing & laying 400 micron thick transparent Poly Vinyl Chloride sheet on the roof under mud phaska cutting placing complete job. |
| 134 | Making Khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 Coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x 1m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet complete incl. all leads, lifts & carriage of material by MT/ H.L. |
| 135 | Providing gola 75 x 75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10mm down gauge) including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design in 75 x 75 mm deep chase incl. all leads, lifts & carriage of material by M.T / H.L. |
| 136 | Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster preparing the surface of mud phaska to proper slope, relaying plaster gobri leaping and tiles and bricks, grouted in cement mortar 1:3 (1 cement :3 fine sand ) including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) including all leads, lifts & carriage of material by MT / H.L. |
| 137 | Taking out doors, windows,windows and clerestory window shutters (steel or wood) of area of 3 square metres and below including stacking of material, all leads and lifts. |
| 138 | Dismantling old plaster or skirting, raking out joints & cleaning the surface for plaster including disposal of rubbish to the dumping ground with all leads & lifts. |
| 139 | Dismantling tile work for thickness of tiles 10 mm to 25 mm in floors and walls laid in cement mortar including stacking material, all leads & lifts. |
| 140 | Dismantling wooden trellis work excluding frames but including stacking the serviceable material including all leads & lifts. |
| 141 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking of area 3 sqm and below ,all leads & lifts. |
| 142 | Dismantling of flushing cistern of all types ( C.I /PVC/Vitreous china) incl. stacking of useful materials near the site & disposal of unserviceable materials incl. all leads, lifts & carriage of material by MT/H. L. |
| 143 | Dismentling C.I. or Asbestos rain water pipes of 100 mm dia pipes with fittings and clamps including stacking the material , all leads & lifts. |
| 144 | Removing mortar from brick work in cement mortar and cleaning bricks including stacking of material, all leads & lifts ( stacks of cleaned bricks shall be measured). |
| 145 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits & the like not exceeding 10 sqm on plan, including dressing of sides & ramming of bottoms , incl. disposal or filling of excavated earth wherever required as per the directions of Engineer-in-charge . |
| 146 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, lead upto 50 meter and lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil |
| 147 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L. |
| 148 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1 : 4 :8 ( 1 cement : 4 coarse sand : 8 graded crushed stone aggregate 40 mm nominal size) including all leads, lifts and carriage of material by MT / H.L. |
| 149 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3 : 6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L |
| 150 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:. 1 : 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20 mm nominal size ) incl. all leads, lifts and carriage of material by MT / H.L |
| 151 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L |
| 152 | Providing and laying damp proof course 40 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by MT/H.L. |
| 153 | Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by MT / H.L. |
| 154 | Providing and laying dry stone agg. using 40mm nominal size incl. spreading, levelling,sand grouting, watering, ramming, etc all complete incl. all leads, lifts & carriage of material by MT / H.L. |
| 155 | Brick work in cement mortar common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curring in Cement mortar 1:6 ( 1 cement : 6 coarse sand) including all shapes, leads, lifts and carriage of material by MT / H.L. |
| 156 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level incl. all leads, lifts and carriage of material by M.T. H.L. |
| 157 | Half brick masonry with bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 ( 1 cement :4 coarse sand) including all leads, lifts and carriage of material by MT / H.L. |
| 158 | Extra for half brick masonry in superstructure above plinth level upto floor V level including all leads, lifts and carriage of material by M.T. H.L. |
| 159 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) incl. all leads, lifts and carriage of material by M.T. / H.L. |
| 160 | 12mm cement plaster of mix 1:4 (1 cement : 4 fine sand) incl. all leads, lifts & carriage of material by MT / H.L. |
| 161 | 15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand) including all leads, lifts and carriage of material by MT / H.L. |
| 162 | Repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq. metres & under including cutting the patch in proper shape ranking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground ,all leads and lifts. |
| 163 | Making plinth protection 50 mm thick of cement concrete 1:3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed & consolidated & grouted with fine sand including finishing the top smooth. Crushed aggregate including all leads, lifts and carriage of material by MT/H.L. |
| 164 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone agg. 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L. . |
| 165 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L. . |
| 166 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level incl.curing but excluding cost of centering shuttering, finishing and reinforcement 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). incl. all leads, lifts and carriage of material by MT/H.L. |
| 167 | Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete Thermo Mechanically Treated bars /Cold twisted bars including all leads, lifts and carriage of material by MT / H.L. |
| 168 | Centring and shuttering including strutting propping etc and removal of form work for |
| 169 | Foundations, footings, bases of columns etc. for mass concrete |
| 170 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 171 | Suspended floors, roofs, landings, balconies and access platform. |
| 172 | Columns, pillars, piers, abutments, posts and struts. |
| 173 | Edges of slabs and breaks in floors and walls under 20 cms wide. |
| 174 | Raking out joints in lime or cement mortar and preparing the surface for repainting or replastering including disposal of rubbish to the dumping ground with all leads and lifts. |
| 175 | Flush pointing with cement mortar 1:3 ( 1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska with non modular brick tiles |
| 176 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed & fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or with dash fasteners shall be paid for separately) |
| 177 | Sal Wood |
| 178 | 2nd Class Deodar Wood |
| 179 | 2nd Class Kail Wood |
| 180 | Providing and fixing 35mm thick wire gauze shutters of Second Class deodar wood using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : |
| 181 | Providing and fixing 35mm thick glazed shutters of Second class deodar wood for doors, windows and clerestory windows using 10 kg/ sqm (4 mm thick) float glass panes including black enameled ISI marked M.S. butt hinges bright finished of required size with necessary screws. |
| 182 | Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with inecessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class deodar wood |
| 183 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick , Particle Board 12 mm thick plain particle board flat pressed, three layer or graded wood particle board medium density grade IS: 3087 marked. |
| 184 | Providing and fixing 35mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws incl. all leads, lifts and carriages of material by M.T/H.L |
| 185 | Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 2nd class teak wood beading 62 x 19 mm |
| 186 | Providing 40x 5 mm flat iron hold fast 40cm long incl. fixing to frame with 10mm diameter bolts nuts and wooden plugs with embeddings in cement concrete blocks 30 x 10 x15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size including all leads, lifts and carriage of material by MT / H.L. |
| 187 | Providing and fixing 16 mm thick gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen plateform,vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curring moulding and polishing to edge to give high gloss finish etc. complete at all levels Granite of any colour and shape(Area of slab upto 0.50 sqm) |
| 188 | Providing edge molding to 18 mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer- in -Charge. for granite work |
| 189 | Extra for providing opening of required size and shape for wash basins/ kitchen sink platform, vanity counters and similar location in marble/ stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. |
| 190 | Providing and laying vitrified floor tiles in size of tile 60 cm x 60 cm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% & confirming to IS: 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 (1 cement : 4 coarse sand) including grouting the joints with white cement & matching pigments etc. complete including all leads, lifts and carriage of material by MT / H.L. |
| 191 | Providing and laying matt finished vitrified tile of 300 x 300 x 9.8 mm size having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge. |
| 192 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 193 | Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including all leads, lifts and carriage of material by MT / H.L. |
| 194 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge |
| 195 | Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Medium shade using 50% white cement and 50% ordinary cement. |
| 196 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete 50 mm thick with 20mm nominal size stone aggregate |
| 197 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : including all leads, lifts and carriage of material by M.T/ H.L.Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 198 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 199 | Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In grating, frames, guard bar, ladders railing, brackets, gates & similar works. |
| 200 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 201 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing & staircase railing and similar work including applying a priming coat of approved steel primer. G.I.pipes |
| 202 | Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm and braced with flat iron diagonals 20 x 5 mm size with top and bottom rail of T-iron 40 x 40 x 6 mm with 40 mm dia, steel pulleys complete with bolts, nuts locking arrangement, stoppers, handles including applying a priming coat of approved steel primer. |
| 203 | Providing and fixing 1 mm thick M.S. steel door with frame of 40 x 40 x 6 mm angle iron and 3mm M.S. gusset plates at the junction and corners , all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece. |
| 204 | Providing and fixing M.S. grills of required pattern in frames of windows etc with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete |
| 205 | Fixed to openings/ wooden frames with Rawl plugs screws etc. |
| 206 | Fixed to steel windows by welding. |
| 207 | Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.) |
| 208 | For fixed portion anodized aluminum (anodized transparent or dyed to required shade according to IS : 1868 minimum anodic coating of grade AC 15) |
| 209 | For fixed portion Powder coated aluminum ( minimum thickness of powder coated 50 microns) |
| 210 | Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.) For shutters of doors, windows & ventilators including providing and fixings hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required( Fittings shall be paid for separately). |
| 211 | Anodised aluminum ( anodized transparent or dyed to required shade according to IS : 1868, minimum anodic coating of grade AC 15) |
| 212 | Powder coated aluminum (minimum thickness of powder coated 50 |
| 213 | Providing and fixing glazing in aluminum door, window, ventilators shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.( Cost. Of aluminum snap beading shall be paid in basic item) With floating glass panes of 4.0 mm thickness ( weight not less than 10.00 kg/sqm) |
| 214 | Providing and fixing ACP sheet panelling 4.0 mm thick in Partition/doors of approved quality as per the direction of Engineer- in - Charge (Complete job) |
| 215 | Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. |
| 216 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment) |
| 217 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 218 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing & cover plates with brass pivot\\" & single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With Stainless Steel cover plate minimum 1.25mm thickness. |
| 219 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts & bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) complete job. |
| 220 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type). |
| 221 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 222 | Providing and Fixing of PVC Panelling including cutting jointing, fixing etc complete job of good quality |
| 223 | Providing and Fixing of PVC false ceiling including cutting jointing, fixing etc complete job of good quality |
| 224 | Providing and fixing Honour Board of size 1.20m x 0.75m incl. c/o acrylic sheet and lettering complete job |
| 225 | Providing & fixing of PVC window blinds of good quality incl rod and brackets complete job |
| 226 | Providing & fixing of Acrylic Plate incl. Lettering complete job |
| 227 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 228 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats ) over & including priming coat with cement primer. |
| 229 | Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work. |
| 230 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 231 | Wall painting with acrylic emulsion paint of approved brand and manufature to give an even shade. Two or more coats on new work. |
| 232 | Wall painting with plastic emulsion paint of approved brand and manufature to give an even shade. one or more coats on old work. |
| 233 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.One or more coats on old work. |
| 234 | Painting with synthetic enamel paint of approved brand brand manufacture to give an even shade. Two or more coats on new work |
| 235 | Providing and applying White Cement based Putty of average thickness 1 mm of approved brand & manufacture, over the plastered wall surface to prepare the surface even & smooth complete. |
| 236 | Providing and applying White Cement based Putty of average thickness 2 mm of approved brand & manufacture, over the plastered wall surface to prepare the surface even & smooth complete. |
| 237 | Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work ( hard & soft wood) |
| 238 | Finishing walls with water proofing cement paint of required shade:Old work ( one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litres/10 sqm complete including cost of priming coat. |
| 239 | Finishing walls with water proofing cement paint of required shade:Old work (one or more coats applied @ 2.20 kg/10sqm) complete. |
| 240 | Finishing wall with water proofing cement paint of required shade - New work (two or More coats) applied @ 3.84 kg/10 sqm |
| 241 | Finishing wall with acrylic smooth exterior paint with required shade on New work (two or more coats applied) @ 1.67 litre/10 sqm over & including base Coat of water proofing cement paint applied @ 2.20 kg/10 sqm. |
| 242 | Finishing walls with Acrylic smooth exterior paint of required shade Old work ( two or more coats applied @ 1.67 litres/10 sqm on existing cement paint surface) |
| 243 | Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface . |
| 244 | Color washing such as green blue or buff to give an even. New work ( two or more coats) with a base coat of white washing with lime. |
| 245 | White washing with lime to give an even shade on New work (three or more coats) |
| 246 | White washing with lime to give an even shade : Old work (two or more coats) |
| 247 | Cleaning of septic tank by mechanical means complete job |
| 248 | Labour Charges for Carpentor/ Mason/Plumber/Electrician /Welder or equavailent skilled type |
| 249 | Labour Charges for Mazdoor/Helper |
| 250 | Hire charges of Welding/ gas welding set including cost of weding rods etc. |
| 251 | Providing and fixing wall to wall matting (complete item) |
| 252 | Providing and fixing wall to wall floor acrylic carpeting (complete item) |
| 253 | Supplying and filling at site Good earth including all leads, lifts and carraige of material. |
| 254 | Supplying and laying including digging, carrying by lorry, filling River Bed Material including watering & consolidation in layers to specified lines, camber, grades and cross sections. Finished work including material , labour all leads , lifts and carriage of material by MT/HL. |
| 255 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation7.5 bricks & S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design |
| 256 | Supplying and filling of stone dust at site, including all leads, lifts and carriage of material by MT / H.L. etc. complete |
| 257 | Supplying of Following Tent house items fittings:- |
| 258 | Hire Charges for Providing & installation of Shamiana of size 15-0// x 15/-0// with side curtain complete job. |
| 259 | Hire Charges for Providing and laying matting /red mat complete job. |
| 260 | Hire Charges for providing and installation of Table with paper roll etc.complete job, per No. per Day. |
| 261 | Hire Charges for providing and installation of Plastic Chairs complete job, per No. per Day. |
| 262 | Hire Charges for providing and installation of VIP Chairs complete job, per No, per Day. |
| 263 | Hire Charges for providing and installation of Pedestal fans Complete job, per No. per Day. |
| 264 | Hire charges for providing and installation of 3 seater VIP Sofa complete job |
| 265 | Hire charges for providing and installation of 2 seater VIP Sofa complete job |
| 266 | Hire charges for providing and installation of Portable Fan Complete job |
| 267 | Engaing Mahindra pickup /tractor with trolley for carriage of Sofa, Table etc. (within 3 km distance per trip) |
| 268 | Providing and installation of stage including construction of front decorative 4 ft height ( with certified drawing and design of load bearing capacity of minimum 15 person at a time ) for sitting arrangements of VIP's by way of providing and installation of temporary columns and beams covered with decorative clothes of different colours with polythene sheet over it, including carriages per day (Complete job) . |
| 269 | Providing and installation of stage including water proofing roof (temporary) for sitting arrangements of VIP's by way of providing and installation of temporary columns and beams covered with decorative clothes of different colours with polythene sheet over it, including carriages per day (Complete job) . |
| 270 | Providing and fixing/writing of flex board including proper anchoring legs/stand (Complete job) . |
| 271 | Providing and installation of 2.50 tonne capacity of air conditioner at VIP stage complete job |
| 272 | Decoration by using Flowers ( including cost of making garland,labour and carriages all complete job |
| 273 | Supplying of Following catering and food supply items incl. c/o crockery/cutlery |
| 274 | Tea/Coffee |
| 275 | Sandwich |
| 276 | Water Bottle(500 ml) |
| 277 | Water Bottle(250 ml) |
| 278 | Water Bottle(1000 ml) |
| 279 | Coconut Water packed (200 ml) |
| 280 | Pakoda ( mix) |
| 281 | Pakoda ( Paneer) |
| 282 | Samosa |
| 283 | Dry fruit Tray (Almond 250 gm, Cashew nut 250 gm, Pista 250 gm, Raisin 250 gm) |
| 284 | Sweets (Barfi, Gulab Jamun) |
| 285 | Veg Meal VIP (Dal, Mix Veg, Matar Paneer, Rice, Raita, Salad, Naan) |
| 286 | Veg Meal (Dal, Rice) |
| 287 | Waiter with proper uniform/ dress for serving food |
| 288 | Providing and fixing inauguration stone (granite of size 3/x 2/) including engraving , painting, writing and const. of pedestal of size 4'-6\\"x 5'-6\\" by way of brick work and plastering, painting incl. all leads , lifts and carriage of material by M .T./H.L. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
