|
| 1 | 2 percent for design consultancy and proof checking and SBC determintion along with submission of the detailed structural, archetectual drawings (including sanitary,plumbing, electrical) designs, calculation of SBC and other relevant test reports, detailed estimate/BOQ in hard and soft copies duly vetted from NIT or IIT or Design directorate. Detailed estimate/BOQ provided should not exceed the advertised quantities/amount. |
| 2 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet |
| 3 | Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead : of sectional area 40 sqcm. and above. |
| 4 | Dismantling steel work in built up sections in angles, tees, flats andchannels including all gusset plates, bolts, nuts, cutting rivets, welding etc.including dismembering and stacking within 50 meters lead. |
| 5 | Taking out doors, windows and clerestory window shutters (steel or wood)including stacking within 50 meters lead : Of area of 3 sqm. and below |
| 6 | Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In Lime mortar or mud |
| 7 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 8 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. Ordinary Rock |
| 9 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 25 meter beyond 1 m from cutting edge |
| 10 | Providing and laying in position cement concrete of specified grade including curing but 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)excluding the cost of centring and shuttering. All work upto plinth level with. |
| 11 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, fmishing and reinforcem 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size: |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 14 | Reinforced cement concrete work in arches, archribs, domes, vaults shells, folded plate and roofs having slope more than 15° upto floor five level level including curing but excluding the cost of centering, shuttering finishing and reinforcement with: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars |
| 16 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 17 | Centering and Shuttering including strulling, popping and removal of form work: Foundation and Plinth |
| 18 | Centering and Shuttering including strulling, popping and removal of form work: Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 19 | Centering and Shuttering including strulling, popping and removal of form work: Columns, pillars, piers, abutments, posts and struts |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms. |
| 21 | Centering and shuttering including strutting, propping etc. and removal of form for Stairs (excluding landings) except spiral staircases. |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 23 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 24 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 25 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 26 | Structural steel work in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded |
| 27 | Providing corrugated G. S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G. I limpet washers or with G. I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusse 0.50 mm thick with zinc coating not less than 27 5gm/m 2 |
| 28 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2 |
| 29 | Providing and fixing plained eaves boarding. 250x32 mm (nominal size ) |
| 30 | Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) :Natural colour insulating board 12 mm thick. |
| 31 | Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo I Fir wood |
| 32 | Providing and fixing wooden moulded corner beading of size 50 x 50 mm (base and height) of triangular shape to the junction of paneling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete.Second class kail wood |
| 33 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately)2nd class Kail wood |
| 34 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including lSI marked M.S. pressed Butt hinges bright finished of required size with necessary screws excluding panelling which will be paid for separately,al!complete as per direction of engineer- in charge. Second class kail wood 30 mm |
| 35 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 12 mm thick Coir Veneer Board (conforming to IS: 14842) |
| 36 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class Kail wood 30mm |
| 37 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:2nd class teak wood 50 x 12 mm |
| 38 | Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigmentsetc. complete Size of tile 600x600 mm |
| 39 | providing and laying polished granite stone flooring in required design and pattern in linear as well as curvilinear portion of the building all complete as per the architectural drawing with 18 mm thick stone slab over 20mmm (average )thick base of cement motar 1;4 (1cemnt: 4coarse sand)laid in jointed with cement sullary and pointing with white cement slurry admixed with pigment of matching shade including rubbing curing and polishing etc all complete as specified and as directed by engineer incharge 11.68.1 polished granite stone slab jet black' cherry red elite brown cat eye equivalent |
| 40 | Cement plaster in 1:6 ( 1 cement:6 fine sand ) ,15mm thick. |
| 41 | 12 mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 42 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 43 | Providing and fixing hand rail of approved Size by welding etc. to steelladder railing, balcony railing, staircase railing and similar works, includingapplying priming coat of approved steel primer.M.S. tube |
| 44 | Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approvedsteel primer all complete.Fixed to openings / wooden frames with rawl plugs screws etc. |
| 45 | Providing and Applying white cement based putty of average thickness 1mm of approved brand and manufactured over the plastered wall surface to prepeare the surface even and smooth |
| 46 | Distampering with oil based bound washable distemper of approved brand and manufactured on wall surface new work ( two or more coar) ocer and including priming coat with cement primer. |
| 47 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 48 | Painting with synthetic enamel paint of approved brand and manufactureto give an even shade Two or more coats on new work. |
| 49 | Providing and fixing aluminium sliding door bolts ISI marked anodize ( anodic coating) not less than grade AC10 as per IS 1868) transpaent or dyed to required colour or shade with nuts and screw etc complete (300 x 16)mm |
| 50 | Providing and fixing Aluminium tower bolts ISI marked anidized (anodic coating) not less than grade AC 10 per IS 1868) transpaent or dyed to required colour or shade with screw etc complete (100 x 10 mm)mm |
| 51 | Providing and fixing Aluminium tower bolts ISI marked anidized (anodic coating) not less than grade AC 10 per IS 1868) transpaent or dyed to required colour or shade with screw etc complete (200 x 10)mm |
| 52 | Providing and fixing Aluminium hanging floor door stopper ISI marked anidized (anodic coating) not less than grade AC 10 per IS 1868) transpaent or dyed to required colour or shade Single rubber stopper. |
| 53 | Providing and fixing Aluminium handels ISI marked anidized (anodic coating) not less than grade AC 10 per IS 1868) transpaent or dyed to required colour or shade with nuts and screw etc complete 125mm |
| 54 | Providing and fixing Aluminium handels ISI marked anidized (anodic coating) not less than grade AC 10 per IS 1868) transpaent or dyed to required colour or shade with nuts and screw etc complete 100mm |
| 55 | Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30 x 10 x 15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 56 | Providing and fixing bright finished brass hard drawn hooks and eyes 200 mm |
| 57 | Random Rubble masonry with hard stone in foundation and plinthincluding leveling up with cement concrete 1:6:12 (1 Cement : 6 coarsesand : 12 graded stone aggregate 20mm nominal size) upto plinth levelandcuring complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 58 | Steel work welded in built up sections/framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 59 | Carriage of Sand by mechanical transport including loading , unloading & stacking complete lead upto 40 km |
| 60 | Carriage of stone aggregate below 40 mm size by mechanical transport including loading , unloading & stacking complete lead upto 50 km |
| 61 | Carriage of Cement by mechanical transport including loading , unloading & stacking complete lead upto 50 km |
| 62 | Carriage of Steel by mechanical transport including loading , unloading & stacking complete lead upto 50 km |
| 63 | Carriage of CGI Sheets by mechanical transport including loading , unloading & stacking complete lead upto 50 km |
| 64 | Carriage of Bricks by mechanical transport including loading , unloading & stacking complete lead upto 260 km |
| 65 | Carriage of Sand by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 66 | Carriage of Stone Aggregates by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 67 | Carriage of Cement by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 68 | Carriage of Steel by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 69 | Carriage of CGI Sheets by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 70 | Carriage of Bricks by manual means including loading , unloading & stacking complete lead upto 2000 m |
| 71 | Carriage of Excavated earth by manual means including loading , unloading & stacking complete lead upto 500 m |
| 72 | Carriage of Stone by manual means including loading , unloading & stacking complete lead upto 500 m Please Enable Macros to View BoQ information |
