|
| 1 | Excavation in foundation trenches etectra in earth work in all kinds of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiseling or wedging out rock where blasting is prohibited, or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads, as directed by Engineer-in-Charge and then returning the stacked soil in 15cm (fifteen centimeters) layers when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials within all leads and lifts. |
| 2 | Supplying and packing of hard stone for under flooring at site including watering, ramming, consolidating, curing and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 3 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres) so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 4 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillar, posts and struts square, rectangular, polygonal and circular in plan including mouldings, cornices etcetera complete as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 5 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings including curved surfaces where ever required as per Architectural drawing, design and specifications and the like floor etcetera including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 6 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels, window sills, cornices, arches, corbelling including curved surfaces where ever required sides and soffits of beams, haunchings, cantilever,s bressumers and lintels upto all depths including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 7 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals, as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 8 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Stair cases (except spiral stair cases) with slopping or stepped soffits excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels as per specifications, approved drawing, design including carriage of material within all heights leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 9 | Providing and laying mechanically mixed and vibrated cement concrete 1:5:10 (one cement isto five sand isto ten graded crushed stone aggregate 40mm (forty millimeter) nominal size) and curing complete, including the cost of form work in foundation and plinth/under floors in all depths including pumping or bailing out water/dewatering and removal of slush as required at site complete and as directed by the Engineer-in-Charge and carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government. |
| 10 | Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (Forty millimeter) nominal size) and curing complete, in or under water, including pumping or bailing out water/dewatering, removal of slush which may arise at the time of laying under water complete including the cost of form work in foundation and plinth in all depths/heights as per HPPWD specifications and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax, Sale tax or any other taxes imposed by the Government. |
| 11 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25N/mm2 (Twenty five newton per square millimetre) with cement contents not less than @ 400 kg/cum (at the rate Four hundered kilogram per cubic metre) or as per approved design mix for foundation and footing all works upto plinth level to give a smooth machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 12 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 2 5N/mm2 (Twenty five newton per square millimetre) with cement contents not less than @ 400 kg/cum (at the rate Four hundered kilogram per cubic metre) or as per approved design mix for columns, pillars, piers, abutments, posts and struts etc all works upto floor five level to give a smooth machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 13 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25N/mm2 (Twenty newton per square millimetre) for reinforced cement concrete work with cement contents not less than @ 400 kg/cum (at the rate Four hundered kilogram per cubic metre) or as per approved design mix in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, corbelling, staircases and spiral stair cases above plinth level up to floor five level to give a smooth mechanically mixed and vibrated inclusing curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 14 | Providing, laying, straightening and fabrication in position Tor steel reinforcement of TISCO/SAIL/JINDAL-PANTHER/ RINL steel for reinforcement thermo mechanically coated bars of grade Fe 500D for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals for its completion up to all floor levels as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is excluding the cost of material and inclusive of Royality, Malkhana, Octroi, GST, Toll Tax, Sale tax or any other taxes imposed by the Government. |
| 15 | Providing and laying damp-proof course 45 mm ( forty five milimetre) thick with cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20mm nominal size)for all works up to all floor levels including carriage of material within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 16 | Brick masonry work with IInd class common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point Five) in super structure in Cement mortar 1:6 (One cement : Six coarse sand) including curing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 17 | Half brick masonry work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point Five) in super structure in Cement mortar 1:4 (One cement : Four coarse sand) including curing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government. |
| 18 | Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete at ground level upto plinth level in cement mortar 1:6 (1 cement : 6 coarse sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 19 | Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete above plinth level upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 20 | Ruled pointing with 1:3 cement mortar (1 cement : 3 fine sand) in modular bricks in exposed masonary work in proper finishing in true lines & design and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.. |
| 21 | Random Rubble masonary with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( one cement six: coarse sand : twelve graded aggerigate 20mm nominal size) upto plinth level with cement mortar (one cement six: coarse sand :) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 22 | Providing and fixing factory made M.S. Single Rebate Frame (Chaukhat) size 100mm x 50mm of 2mm thickness sheet of APOLLO/ TATA make for doors, windows and ventilators complete, joints mitred and flush butt welded and including providing and fixing of Stainless steel butt hinges of size 100 mm and 2.5 mm thickness with welding and necessary secrews complete all as per approved design and fixing frame with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 23 | Providing and fixing factory made M.S. Double Rebate Frame (Chaukhat) size 130mmx65mm of 2mm thickness sheet of APOLLO/ TATA make for doors, windows and ventilators complete , joints mitred and flush butt welded and including providing and fixing of Stainless Steel butt hinges of size 100 mm and 2.5 mm thickness with welding and necessary secrews complete all as per approved design and fixing frame with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 24 | Providing 6mm (Six millimetre) thick cement plaster in ceiling with cement mortar 1:3 (One cement isto Three sand) upto all floor levels including curing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 25 | Providing and plastering of 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior/exterior plastering including making groove or drip course, arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) upto floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 26 | Providing and plastering of 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior/exterior plastering including making groove or drip course, arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand) upto floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 27 | 18 mm thick plain cement mortar Raised Band in cement mortar 1:4 (1 cement : 4 fine sand) complete up to all floor levels including carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. Total Please Enable Macros to View BoQ information |
