|
| 1 | Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 2 | Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition). (upto 4 storied bldg) complete all as specified and directed. |
| 3 | M&L for Reinforced cement concrete (nominal mix) Type B1 (1:2:4) (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 4 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 5 | M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 6 | All as per item no 5 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 7 | M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 8 | M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walling built in cement mortar (1:4) complete all as specified and directed. |
| 9 | Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed. |
| 10 | M&L for 5mm thick plastering on ceiling surfaces in CM (1:3) surface finished even and fair complete all as specified and directed. |
| 11 | M&L for 20mm thick (in two layer) plastering on fair face of Brick surface with CM (1:4) and mixing with WPC finish surface even and smooth without using extra cement complete all as specified and directed.Note:WPC shall be measured and paid seperately as supply only |
| 12 | M&L for 15mm thick cement plaster with CM (1:6) on other than fare face of brick wall finsh even and smooth without using extra cement complete all as directed. |
| 13 | Dismantling removing all unsound concrete, plastered material by chipping/chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached all various locations in building (upto 4 storied) subsequently cleaning the surfaces by hair brush and air blower and removing rubbish off the premises and disposing at the dumping site as approved by local authorities including hoisting assembling and fixing of double layer steel scaffolding to external perimeter of building complete all as specified and directed . |
| 14 | Removing of concrete all around reinforcement bar upto 20 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiseling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified . Make( Rust removing chemical ):- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP. |
| 15 | Material , labour and preparation of existing reinforcement surface by brush and application of two component epoxy zincrich primer on existing reinforcement surface of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre. complete all as specified . Make- Nitozinc primer of FOSROC or equivalents SIKA/STP |
| 16 | Material and labour for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc all as specified. |
| 17 | M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion of Sika Rep Microconcrete-4 or renderoc-RG of Fosroc in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc of equivalent at various locations in Bldgs including necessary form work complete all as per manufactures specification. |
| 18 | M&L for providing and applying at two component structural grade polymer modified reinforcement mortar Fosroc Renderoc S2 or equivalent product of SIKA upto a thickness of 30 mm over a coat of epoxy resin bonding agent Nitobond EP. The cured mortar shall achieve a minimum compressive strength of 12N/mm2 in a day & 45 N/mm2 in 28 days with Flexural strength 8N/mm2 in 28 days Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. in addition to this percentage of water absorption should be 0.45 after 24 hours in immersion test at various locations in Bldgs complete all as per manufacture's specification |
| 19 | Material and labour for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified.(upto 4 storied bldg) Make:- Concure LP90 of FOSROC or equivalents solutions SIKA/STP/ Maruti / Choksey chemicals. |
| 20 | M&L for providing and applying a flexible expansion joint membrane of minimum 150mm wide and 1mm thick, expoband one (Expoband H45) of FOSROC or equivalent over the prepared joint using a two part epoxy adhesive nitobond PC 40 of Fosroc or equivalent. The minimum tensile strength of the membrane should be more than 12 N/mm2 and elongation at break should be more than 400%. The installation of the membrane should be carried out as per manufactures specification complete all as specified and directed. |
| 21 | S&F shear connector of 8mm dia & requisite length on the surface to be repaired for the bonding between old and new concrete as per the locations instructed by the Engr-in-Charge. The shear connectors shall be of L shape and welded with existing reinforcement at least 100mm in length @ 200mm c/c both horizontally and vertical followed by coat of epoxy Zinc primer as per the specification mentioned complete all as specified and directed. |
| 22 | M & L for providing and inserting mild steel shear key bars/levelling gauges of required length and diameter in reinforced/plain concrete for drilling suitable holes in RCC Slab/ wall/ column/ beams toa depth as directed for anchoring steel reinforcement bars including washing with water inserting lokfix 'E' of Fosroc or equivalent in the holes at various location in Bldgs complete all as per manufactures specification. |
| 23 | M&L for providing grouting in RCC walls and slabs by drilling holes @300 mm c/c upto half of the wall depth in zigzag manner using a drill machine and fixing a nozzle of 20mm dia, for injecting of epoxy grout till the refusal of injected grout material (grouting operation pressure shall be in between 2 to 4Kg per sq cm) followed by cutting the exposed nozzle so as to make the wall/ slab free from the grouting pipe and to seal the gap with polymer modified mortar complete all as specified and directed. |
| 24 | Material & Labour for applying Anti carbonation coating as per manufacturer's specification of approved brand, manually using brushes on the hardened concrete/plastered surfaces after cleaning the surface and removing all loose particles, deposits etc complete including one coat of primer and two coats coatings as complete all as specified and directed. |
| 25 | Material & Labour for Carbon Fibre Wrapping - Nitowrap CWS – 450 GSM Providing and carrying out Fosroc make carbon fibre wrapping Nitowrap CWS (450 GSM) - High Performance high strength, carbon fibre system for structural strengthening to R.C. members. Surface Preparation : Proper surface preparation to be carried out including cleaning, removal of loose material, dust etc, executing required repairing like epoxy injection grouting, polymer modified mortar, epoxy touching Putty , rounding off edges of structural members to 25mm etc . Application : Prepared substrate shall be primed with Nitowrap 30 epoxy primer supplied in pack size 4 Lit (Base-4.1 kg and Hardener -0.46 kg) at a coverage of 8-10 m2/litre/coat, allow the primer to cure for 24 hours followed by application of first coat of saturant Nitowrap 410 supplied in pack size 5kg ( Base - 3kg and hardener - 2kg) (having Tensile strength >30 MPa; Elongation > 2.1% ; Fibre strength > 4900 MPa ; Fibre E-Modulus >230 GPa & Flexural Modulus > 1700 MPa when tested as per ASTM D638 Type I and ASTM D 790 & Glass Transition Temperature > 50 °C as per ASTM E 1356) to be carried out at a coverage of 3.5 to 4 m2/lit/Coat at around 250 microns WFT, cutting of Nitowrap CWS (available in standard roll width of 500 mm and roll length of 50 mtr & 100 mtr) in required size and wrap over wet saturant keeping minimum 150 mm overlap, rolling the same using hard roller to impragnent saturant and again applying second coat of saturant using suitable bush or roller etc, completing as per specification and as directed by Engg.-in-charge. Nitowrap CW fabric used shall exhibit the following properties - fiber density of 1.8 g/cc, dry fibre thickness 0.40mm and shall have tensile strength > 4900 MPa ; tensile modulus > 230 GPa and ultimate elongation of 2.1%.The adhesion of the entire system(FRP Sheet, Saturant and primer combined) with concrete shall be > 3.5 MPa with concrete failure as per ASTM D 4541 complete as per specification and as directed. |
| 26 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 27 | Taking down chowkhats or frame with shutter (without taking off shutters from the frame) exc 1.5 sqm n.exe 4 sqm each complete all as specified and directed. |
| 28 | Taking down chowkhats or frame with shutter (without taking off shutters from the frame) n.exc 1.5 sqm each complete all as specified and directed. |
| 29 | S & F 2nd Hardwood plain solid straight chowkhats,wrought framed rebated on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 30 | M&L for 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match complete all as specified and directed. |
| 31 | S&F for Factory made single extruded WPC(Wood polymer composite) solid door Frames of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), mimimum compressive strength of 58 N/Sqmm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 32 | S&F for Factory made single extruded WPC(Wood polymer composite) solid flush door shutter of 35 mm size comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum density of 650 Kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), mimimum compressive strength of 50 N/Sqmm, modulus of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of termite/borer proof , water/moisture proof & fire retardant & fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed as per directions of Engineer in charge |
| 33 | S&F for Factory made single extruded WPC(Wood polymer composite) solid door Frames of size 45x70 mm comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), mimimum compressive strength of 58 N/Sqmm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 34 | S&F for Factory made single extruded WPC(Wood polymer composite) solid flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum density of 650 Kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), mimimum compressive strength of 50 N/Sqmm, modulas of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of termite/borer proof , water/moisture proof & fire retardant & fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws,complete all as specified and directed as per directions of Engineer in charge |
| 35 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame(88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) Area not exceeding 2.00 sqm each complete all as specified. |
| 36 | All as per serial No 35 but area exceeding 2.0 sqm each complete all as specified and directed as per directions of Engineer in charge |
| 37 | Providing and fixing factory made uPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and directed (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) (A) Area not exceeding 1.00 sqm each |
| 38 | S&F 5.5 mm thick glass ordinary quality, frosted on one side fixed to aluminium frame work exc 0.5 Sq. m in each pane complete all as specified & as directed. |
| 39 | S&F 4.8 mm thick glass ordinary quality, frosted on one side fixed to aluminium frame work n. exc 0.5 Sq. m in each pane complete all as specified & as directed. |
| 40 | S&F Brass 4 levers Mortice lock, vertical type, size 100 mm complete all as specified and as directed |
| 41 | S&F Stainless steel handles 150mm long, bright polished complete all as specified and directed |
| 42 | S&F stainless steel 300mm long sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts complete all as specified and as directed |
| 43 | S&F stainless steel 250mm long sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts complete, all as specified . |
| 44 | S&F stainless steel barrel tower bolts of extruded section with 200 mm long bolt, complete all as specified and as directed |
| 45 | S&F stainless steel anodised barrel tower bolts of extruded section with 150 mm long bolt, complete all as specified and as directed |
| 46 | S&F Bearing hinges 100mm, cast brass, with Stainless steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and as directed |
| 47 | S&F for Stainless steel wire cloth having 0.36 mm nominal dia of wire and average width of appreature 1.40 mm and fixed with stainless wire staples complete, all as specified . |
| 48 | S&F 300 mm Rat tail rod pattern spring MS including roller and roller platecomplete all as specified and as directed |
| 49 | S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed |
| 50 | Dismantling floor , hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed |
| 51 | M&L for Anti-skid joint free ceramic (coloured) tiles 7-8mm thick area of each tiles exeeding 0.06sqm but n.exceeding 0.11 sqm in toilet/bath floor etc.set and jointed with adesive and pointed in epoxy grout with spacers including 15mm thick screed bed in CM (1:4) complete all as specified and directed.complete all as specified & as directed. |
| 52 | M&L for glazed ceramic (coloured) tiles of size 450x350 6-7mm thick as in vertical surface/dado set and jointed in adesive and pointed in white or coloured cement to match including 10 mm thick backing coat in CM (1:4 ) complete all as specified and directed. |
| 53 | M&L for Anti-skid joint free ceramic coloured tiles exc 0.18 sqm but n. exc 0.38 sqm 7 to 8 mm, in floors etc. set and jointed in neat cement slurry including 15mm thick screed bed in CM (1:4) complete all as specified and directed. |
| 54 | M&L for double charge vitrified ceramic tiles10 mm thick area of each tiles exceeding 0.42 sqm but not exc 1 sqm,in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed. |
| 55 | M&L for 25mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate complete all as specified and as directed |
| 56 | Supply and applying two coats of High performance elastomeric cementitious waterproof coating sandwiched with 45 GSM glass fibre reinforcement on the entire floor and 1.0 m of all walls of all toilets as per following methodology:- Cleaning of exposed concrete surface by mechanical means or by hydro blasting to remove laitance, loose particles, contamination etc. which may hinder bonding. Covering of RCC joints with PCC (1:1.5:3) mixed with Integral Water Proofing compound. Applying one coat of Waterproofing membrane to concrete surfaces followed by application of 45GSM glass fibre on the wet surface. Applying second coat of waterproofing membrane at the right angles to the direction of first coat. Second coat shall be applied after the first coat gets dry. Sprinkling fine aggregate immediately after the application of second coat to get the mechanical key for protective plaster. Curing to Water proofing membrane to be carried out for minimum period of 3 days with ponding complete. The Water Proofing Product Should have Mixed density: 1.68g/cc (brushable consistency). Adhesion to concrete : >1N/mm2. Static crack accommodation: 1mm complete all as specified and as directed ( Fosroc/Elantas beck/Kunal conchem) ( Make : SIKA/FOSROC/Hindcon/STP ) |
| 57 | M&L for Bore packing of all the Spouts to be done with grouting admixture mixes with Cement Concrete / Mortar @225 ml per bag of Cement complete all as specified and as directed. |
| 58 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed |
| 59 | Taking up or down 15mm bore steel water tubing and connections,including cleaning for removal to store(GI Pipe) complete all as specified and as directed. |
| 60 | Taking up or down 20mm bore steel water tubing and connections,including cleaning for removal to store(GI Pipe) complete all as specified and as directed |
| 61 | Taking up or down 25mm bore steel water tubing and connections,including cleaning for removal to store(GI Pipe) complete all as specified and as directed |
| 62 | Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed |
| 63 | S&F CPVC pipes 15 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings as in walls, ceiling, floor, etc. complete all as specified and directed. |
| 64 | S&F 20 mm bore (Outer dia) CPVC pipes of SDR 11and plain CPVC SDR 11 fitting fixed on wall or floor (concealed ), ceiling or laying in floors complete all as directed. |
| 65 | S&F in 25 mm bore (Outer dia) CPVC pipes of SDR 13.5 and plain CPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as directed. |
| 66 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed |
| 67 | S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and as directed |
| 68 | S&F 25 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and as directed |
| 69 | S&F 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and as directed |
| 70 | S&F 25mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and as directed |
| 71 | S&F PVC (SWR) bends 110mm dia complete all as specified and as directed |
| 72 | S&F PVC (SWR) junction single, (Single T) equal or unequal 110 mm dia complete all as specified and as directed |
| 73 | S&F PVC (SWR) junction double, (Double T) equal or unequal 110 mm dia complete all as specified and as directed |
| 74 | S&F in repairs vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed. |
| 75 | S&F in repairs vitreous China wash down water closet pan ( padestal pattern) incl PVC seat cover , (excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe , etc., complete complete all as specified. |
| 76 | S&F in repairs vitreous china wash hand basin, white, flat back, size 550mm x 400mm, exc chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed. |
| 77 | S&F in repairs Brass chromium plated 32 mm bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed |
| 78 | S&F in repairs 15mm bore CP angular valve fancy type,with crutch handle, screwed for iron pipe or for brass ferrule and fixed of following size complete all as specified and directed. |
| 79 | S & F in repairs 15 mm Dia CP Bib taps,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed |
| 80 | S & F in repairs 15 mm Dia CP Bib taps (Two-in-one), fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed |
| 81 | S & F in repairs 15 mm Dia CP stop cock(concealed type) , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed |
| 82 | S&F in repairs 15 mm bore CP pillar taps, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure ,complete all as specified and directed. |
| 83 | S & F in repairs 25 mm Dia brass gun metal gate valve , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed |
| 84 | S&F in repair CP Health faucet with all necessary fittings complete all as specified and as directed .Make : Prayag/Cera/Jaquar or equivalent. |
| 85 | S&F in repair 600 mm PVC connection pipe 15 mm size with PTMT nut of following length complete all as specified and directed . |
| 86 | S & F in repair 110/125 mm floor trap fixed in floor with grating incl jointing with solvent cement (1:2:4) concrete,complete all as specified and as directed |
| 87 | S&F 600 mm x 450 x 6 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick| AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass| screws and cup washers comlete all as specified and directed. |
| 88 | S&F in repair brass CP Shower roses in repair with or without swivel joints, 125mm size, including fixing to steel pipes or union comlete all as specified and directed. |
| 89 | S&F CP Soap dish, fixed to plugs with chromium plated brass screws comlete all as specified and directed. |
| 90 | S&F in repair brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specfied and directed. |
| 91 | S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approved by GE complete all as specified & directed. |
| 92 | M & L for Cement concrete in roof kerb or mud stop rounded on edges etc Type B1 1:2:4 (20 mm graded aggregate) slope maintained as per site requirement complete in all respect complete all as specified and as directed |
| 93 | Supply only water proofing compound |
| 94 | Dismantling of old unserviceable water tank, removing from site, Supply and fixing of rotational moulded polythene water storage tank 1000 litre capacity ISI marked (cylindrical, vertical, double layered with closed top) hoisted and fixed in position including PVC float valve 20mm bore weight not less than 210gms. complete all as specified and as directed |
| 95 | All as per item No 94 above but capacity 2000 litre complete all as specified and as directed |
| 96 | Taking out/Stripping of old Roof treatment membranes/Tar felt incl layer of cement mortar of any type carefully from roof surfaces (without damaging roof ) and incl preparation of old roof surfaces by picking, sweeping, cleaning and washing down with water to remove dust & receive new treatment complete all as specified and directed. (upto 4 storied bldg) |
| 97 | M&L for water proofing treatment on cleaned RCC roof comprising with the following operation and as specified here in below. (a) 10 mm thick (av. Minimum thickness) plastering in cement mortar 1:3 finishing the plastered surfaces even and smooth over cleaned Rcc roof. The plastered surface shall be cured properly for ten days by ponding of water over roof. (b) Applying bitumen primer over the plastered surface @ 0.40 Kg/ Sqm .(c) a coat of bonding material with applying hot blown bitumen 85/25 @1.2 kg/sqm (d) providing and laying 3 mm thick APP (minimum thickness) (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.0 kg/Sqm water proffing membrane, black finished reinforced with non woven polyester matt make as approved over the primer coat. Membrane shall be laid using butane torch and sealing all joints etc all as per Para 11.44.5 of SSR Part I (e) Applying two coat of Aluminium paint with one coat of aluminium primer over APP based polymetric membrane complete all as per manufacturer's instruction( Note : The work shall be executed through authorized applicator approved by the manufacturer of members) |
| 98 | S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 99 | M&L for Complete removal of existing treatment by using electric sander machine or steel wire brushing to remove all dust and loose scale etc of wall surfaces & prepare to receive wall care putty complete all as specified & directed. (upto 4 stoey bldg) |
| 100 | M&L for preparation of newly plastered wall surface two coats of oil emulsion distemper over a coat of primer on complete all as specified and directed.(upto 4 stoey bldg) |
| 101 | M&L for preparation old decorated walls & applying two coats of acrylic oil bound distemper over a coat of 1mm thick wall care putty complete all as specified and directed.(upto 4 stoey bldg) |
| 102 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over 2mm thick wall care putty and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 103 | M&L for preparation of new decorated Ceiling surfaces & applying two coats of acrylic oil emulsion distemper over a coat of chalk whiting complete all as specified and directed. |
| 104 | M&L for preparation of old decorated Ceiling & applying one coats of acrylic oil emulsion distemper complete all as specified and directed.(upto 4 storey bldg) |
| 105 | M&L for preparing of new steel surfaces & applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and as directed.(upto 4 stoey bldg) |
| 106 | M&L for preparing of old steel surfaces and applying one Coats of Synthetic Enamel Paint over one coat of primer to steel and iron surfaces of any description, not otherwise described including preparation of old surface complete all as specified and directed.(upto 4 stoey bldg) |
| 107 | M&L for Two coats of synthetic enamelled paint on New wooden surface exc 10cm width or girth including preparation complete all as specified and as directed. |
| 108 | M&L for one coat of synthetic enamel paint, area exc.10cm width or girth over Old painted wooden surfaces including preparation of surface complete in all respect as specified and directed |
| 109 | S&F in repairs Curtain rod 20 mm dia Aluminium fancy type complete with clamps, ring, ball shaped knobs at both end, all golden colour, complete all as directed by Engr-in-charge. |
| 110 | S & F stainless steel sink made of 1.00 mm thick sheet for kitchen or laboratory with plug, washers waste pipe including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets,connecting union to pipe, overall size 495mmx420mm, bowl size 410x330x160mm complete all as specified and as directed |
| 111 | M & L for granite 18 to 20 mm thick (PURE BLACK) (table rubbed and polished) as in steps, jambs, pillars, window cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in CM (1:4)Edges of slab to be rounded from all sides complete all as specified and as directed ( including cutting,wastage and polishing). |
| 112 | S&F in repair wall mixture3-in -1 system with provision for both hand shower and overhead shwer complete with 115mm long bend pipe, connecting legs and wall flange(with hand & over head shwer) telephonic brass CP tap for mixing hot and cold water including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete all as specified and as directed |
| 113 | S&F in repair wash hand basin mixture Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hos Brass CP tap for mixing hot and cold water including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete all as specified and as directed |
| 114 | Taking down old rusted u/s steel collapsible gates or rolling shutters any size including taking out holdfasts/anchorages and other fixtures complete all as specified complete all as specified and directed. |
| 115 | S&F in Repair 1.25 mm steel rolling shutters without ball bearing,as specified including top cover,anchoring,hasp and staple and one shop coat of primer erected in position as indicated,complte: but gear operated type with chain wheel and hand chain complete all as specified and as directed |
| 116 | M&L in repairs Cement contrete Chequered tiles 25cm x 25 cm x 22 mm thick Chequered tiles with grey cement and colour pigment including 15 mm thick screed bed in CM (1: 4) complete all as specified and directed |
| 117 | M & L for Cement concrete in surface channel/drain Type B1 (1:2:4) (20 mm graded aggregate) slope maintained as per site requirement complete in all respect as specified and directed |
| 118 | M&L for 75mm thick PCC (1:3:6), type C2, using 40mm graded stone aggregate complete as specified and directed. |
| 119 | M&L for 100 mm thick PCC (1:3:6), type C2, using 40mm graded stone aggrigate complete as specified and directed. |
| 120 | M&L in repairs for Machine pressed concrete interlocking paver block 80 mm thich M-40 grade conforming to IS 15658 -2006 complete all as specified and as directed |
| 121 | M&L for sand cushion for paver block not exceeding 40 mm thick complete all as specified and as directed |
| 122 | S&F in repairs 18/19 mm Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on both face fixed with timber frame complete all as specified and as directed |
| 123 | S&F 12 mm thick plywood BWR grade type BB fixed on wooden frame/ kitchen cabinate/ drawer etc complete all as specified |
| 124 | M&L for 1.5 mm thick coloured Acrylic sheet lamination on 12 -15 mm thick plywood using thermo mechanically pressed method allaround plywood board for modular kitched cabinate/ drawer etc complete all as specified and directed |
| 125 | S&F 40 mm width of flaps brass piano hinges with bright finishes complete all as specified and as directed |
| 126 | S&F 100 brass handle cast type polished bright complete all as specified and as directed |
| 127 | S&F wall mounted kitchen chimney of 595x240x850 mm, min suction capacity 1400 cum per hour make as approved by GE including all fittings necessary complete all as specified and as directed |
| 128 | S&F Brass knobs 35 to 40 mm dia complete all as specified and as directed |
| 129 | S&F stainless telescopic drawer sliding Heavy duty upto 600 mm long load capacity 40 kgcomplete all as specified and as directed |
| 130 | S&F SS wall mounted plate rack 04 self size 30\\"x32\\" made of Food grade stainless steel of SS 304 or SS316 complete all as specified and as directed |
| 131 | S&F brass Fanlight catch with 14 mm catch and fixed with wood work complete all as specified and as directed |
| 132 | Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, fan regulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from site complete and make good the disturbed surface as existing complete all as specified and as directed Note :(i) cost of unserviceable materials will be charged from the contractor against schedule of credit. (ii) Serviceable light fitting shall be kept in safe custody for reuse at site. (iii) Re-fixing shall be measured and paid seperately. |
| 133 | M&L for Concealed point wiring with 1.5 sqmm PVC insulated FRLSH sheathed 1100 Volts grade copper multi stranded conductor drawn through and including rigid PVC conduit 20 mm dia concealed in walls ,roofs, etc including 1.5 sqmm PVC insulated copper conductor as earth continuity conductor and other accesories such as metal box, sheet cover, screws,nuts etc connecting it to the common earth dolly all as specified for one light/ceiling fan/Exhaust fan / wall fan each controller by one way switch complete all as specified and as directed |
| 134 | All as per item no 133 above but one 3 pin 5 Amps socket outlet on same board controlled by one switch complete all as specified and as directed |
| 135 | All as per item no 133 above but one 3 pin 5 Amps socket outlet independent controlled by one switch complete all as specified and as directed |
| 136 | All as per item no 133 above but with 2.5 sqmm cable copper for 15/16 Amps socket outlet on independent board,including 2.5 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly complete all as specified and as directed |
| 137 | All as per item no 133 above but with 4.0 sqmm cable copper for 15/16 Amps socket outlet on independent board,including 4.0 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly complete all as specified and as directed |
| 138 | All as per item no 133 above but for one bell/buzzer point controlled by one bell push button on the same board with other switches or independent with 1.5 Sqmm copper conductor cables complete all as specified and as directed |
| 139 | All as per item No. 133 above but for one light point controlled by two way switches ditto complete all as specified. |
| 140 | Taking down unserviceable submain wiring any size,complete all as specified and directed. Please Enable Macros to View BoQ information |
| 141 | Taking down unserviceable submain wiring any size,complete all as specified and directed. Please Enable Macros to View BoQ information |
