|
| 1 | Taking down cement plaster of any description from walls, ceilings etc. including raking out joints, hacking for key, scrubbing down with water etc. removal of rubbish off the premises and removal of debris out side from MD land etc complete all as specified and directed. |
| 2 | M&L for 15mm thick rendering in CM (1:6) internal plaster on brick/concrete surfaces finished even and smooth without using extra cement etc complete all as specified and directed. |
| 3 | M&L for rendering in CM (1:4) 20 mm thick in two coats (15 mm under coat + 5mm finishing coat) on brick/concrete surfaces with water proofing compound @3% by weight of cement in finishing coat and finishing the surface even and fair.(Note :- WPC will be measured and paid seperately). |
| 4 | M&L for rendering 5 mm thick on fair faces of brick or concrete surfaces of ceilings in CM (1:3), finished even and smooth without extra cement complete all as specified |
| 5 | Supply only integral WPC all as specified & directed. |
| 6 | M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper paint on walls over a coat of alkali resistant primer including 1.5mm thick wall care putty, complete all as specified and as directed . |
| 7 | M&L for preparation on new plastered surface of wall, chajja, parapet etc and applying two coats of acrylic emulsion paint (two or more coat applied @ 1.67 ltr/10 sqm over including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including 3mm thick wall care putty complete all as specidied and as directed |
| 8 | M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper paint on ceiling over a coat of alkali resistant primer ncluding 1.5mm thick wall care putty, complete all as specified and as directed . |
| 9 | Taking down door/ window shutter with frame (without taking off shutters from frame) of any description exc. 1.50 Sqm not exc 10.00 Sqm each etc complete all as specified and as direted. |
| 10 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 11 | S&F for powder coating of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. |
| 12 | S&F for powder coating of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap eading, screws etc. complete all as specified |
| 13 | Supply only 5.50 mm thick float glass fixed in aluminium sliding window/door shutters etc complete all sas specified and directed. |
| 14 | S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and as direted. |
| 15 | Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineerin- charge. |
| 16 | M&L for 2nd class hardwood for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, Complete all as specified and directed. |
| 17 | M&L for preparation of new wooden surfaces of any description, not otherwise descri-bed, over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of pink primer, Complete all as specified and directed. |
| 18 | S & F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides. complete all as specified and directed. |
| 19 | M&L for 0.90 mm thick decorative laminate type 1, laminates on flat or curved surfaces in any size or width , of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.. |
| 20 | S&F for Butt hinges, medium weight 125MM Size, cold rolled mild steel, and fixed to chowkhat and door, complete all as specified and directed. |
| 21 | S&F for 200mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed. |
| 22 | S&F for 150mm long brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed. |
| 23 | S&F for 250mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed. |
| 24 | S&F for 150mm size extruded brass handles fabricated type, polished etc complete all as specified and directed |
| 25 | S&F for 125mm size extruded brass handles fabricated type, polished etc complete all as specified and directed |
| 26 | S&F for floor door stopper of brass body and tongue with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm. |
| 27 | S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples all as specified. |
| 28 | S&F 30mm thick Glazed and skeleton shutters in 1st class soft wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified. |
| 29 | M&L 2nd class hard wood Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area n exc. 3 sq.cm, complete all as specified and as directed. |
| 30 | M&L for preparing old wooden surface and apply one coat of synthetic enamel paint of any description, not otherwise descri-bed, over 10cm width or girth, complete all as specified and directed. |
| 31 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbish off the premises and removal of debris out side from MD land etc complete all as specified and directed. |
| 32 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick rendering in CM (1:4) as in backing coat complete all as specified and directed. |
| 33 | S&F for glazed ceramic coloured tiles 300x600x7mm thick on vertical surfaces such as skirting / dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM (1:3) as in backing coat complete all as specified and directed. |
| 34 | M&L for Grouting the joints of flooring/wall tiles having joints upto 5 mm width, and upto 10mm depth using white cement or as directed by the Engineer-in-charge and finishing including all surface must be clean, dry, and free from dust, grease, wax, oil, laitance curing compounds and all other contaminates likely to prevent the adhesive bonding and after finishing of grouting then removing of excess grout from the joints, cleaning of tiles and joints surface with in 30 min using sponge-board dampened in clean water, finally, cleaning the entire surface using clean cloth, etc. complete as per direction of Engineer in Charge. |
| 35 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments set, jointed and pointed in neat cement slurry in floors including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 36 | Demolition stone sett/Interlocking paver tiles of any description of thickness laid dry of laid dry by pointing, complete all as specified and directed. |
| 37 | Excavating over areas, n exc 1.5 m deep and getting out in soft loose soil. |
| 38 | M&L for Hardcore of gauge n exc. 63 mm, of broken aggregate,deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface,Complete all as specified and directed. |
| 39 | M&L for 100mm thick (compacted thickness) WBM with coarse aggregates of grading 1 (90 to 40mm size), spread, rolled and consolidated to gradient and camber required, Complete all as specified and directed |
| 40 | M&L for 100mm thick PCC type C-2 (1:3:6) (using 40mm grade stone aggregate) as in sub base of floor and path, Complete all as specified and directed. |
| 41 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, Complete all as specified and directed. |
| 42 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, Complete all as specified and directed. |
| 43 | M&L for brick work with sub class 'B' bricks, straight or curved on plan to any rarius in half brick thick wall, built in CM (1:6) complete all as specified and as directed. |
| 44 | M&L for 10mm thick rendering in CM (1:6) internal plaster on brick/concrete surfaces finished even and smooth without using extra cement etc complete all as specified and directed. |
| 45 | M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper paint on walls over a coat of alkali resistant primer including 1.5mm thick wall care putty, complete all as specified and as directed . |
| 46 | M&L Granite 20mm thick (of any type) work (table rubbed and polished) in cooking platforms and shelf, jambs, window cills, partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specified and directed. |
| 47 | M&L for rounding to edges of stone slabs one edge, such as in steps, columns, cooking platform,window cills and other similar situations complete all as specified and directed. |
| 48 | S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed. |
| 49 | S&F Pillar tap cast copper alloy with capstan head, fancy type, chromium plated screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe & fixed, complete 15 mm dia suitable for kitchen sink/WHB complete all as specified and directed by Engr-in-Charge. |
| 50 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10cm girth, complete all as per specified and directed. |
| 51 | S&F for 15 mm dia bore medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors including takong up or down, complete all as specified and directed. |
| 52 | S&F for 20mm dia bore medium grade galvanised steel tubing with all fittings fixed to walls, ceilings or laid under floors including takong up or down, complete all as specified and directed. |
| 53 | S&F for 15mm bore fancy type bib tap, cromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed inlcuding taking down old complete all as specified and directed. |
| 54 | S&F for 15mm size Stop Valves fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends etc inlcuding taking down old complete all as specified and directed |
| 55 | S&F for soap dish of PTMT any colour fixed with and including CP brass screws and wooden/plastic cleats inlcuding taking down old complete all as specified and directed |
| 56 | S&F for 20mm dia & 60 cm long `D' type, chromium plated brass tubular towel rail between flanges inlcuding taking down old complete all as specified and directed |
| 57 | S&F for CI floor/nahani trap 75mm dia with grating, incl jointing to waste pipe in run lead complete and making good the disturbed surface to match existing surface inlcuding taking down old complete all as specified and directed |
| 58 | Demolition & breaking up drain pipes upto 110/75 mm dia (salt glazed ware, AC,PVC or reinforced concrete) set in cement mortar. |
| 59 | S&F for 75mm bore of pipe PVC (SWR) pipes single socketted in any length with rubber ring joints laid in walls / floors etc complete all as specified and directed. |
| 60 | S&F for 110mm bore of pipe PVC(SWR) pipes single socket in any length with rubber ring joints laid in walls /trenches or in floors etc complete all as specified and directed. |
| 61 | S&F for PVC (SWR) 75mm Bore Bends any radius |
| 62 | S&F for PVC (SWR) 110mm Bore Bends any radius |
| 63 | S&F for PVC (SWR) 75mm Bore vent cowl |
| 64 | S&F for grating doom 100mm dia of PTMT (min weight 25gms) inlcuding taking down old complete all as specified and directed |
| 65 | S&F for grating doom 100mm dia with waste hole of PTMT (min weight 40gms) inlcuding taking down old complete all as specified and directed |
| 66 | S&F for shelf of PTMT fixed with and including chomium plated brass scews and wooden/plastic cleats (Min wt 300 gms) inlcuding taking down old complete all as specified and directed |
| 67 | S&F for PVC connections 15mm size with PTMT nuts of length 600mm |
| 68 | M&L waste cuplings 32mm dia (half or full threads). (minimum weight 32 mm-45grms/40mm- 60grms) |
| 69 | S&F for 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, completed all as per specified and directed. |
| 70 | S&F for Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. Complete all as specified and directed. |
| 71 | S&F PVC valveless, syphonic action type 10 Ltr capacity flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. |
| 72 | Demolition of plain cement concrete and pavings (unreinforced) in any position N. exc 15 cm thick and removal of the same outside MD land etc complete all as specified and directed. |
| 73 | M&L for PCC (1:3:6) type C1 (using 20 mm graded aggregate) 75mm thick as in plinth protection etc complete all as directed by the Engineer-in-Charge. |
| 74 | M&L for 100mm thick PCC type C-2 (1:3:6) (using 40mm grade stone aggregate) as top layer of surface on hardstanding or path, Complete all as specified and directed. |
| 75 | M&L for Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc, Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed. |
| 76 | Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance n exc 50 m in hard/dense soil complete all as specifed and as directed |
| 77 | M&L Plain Cement Concrete Type C2 1:3:6 using 40 mm graded stone aggrgate as in foundation filling and mass concrete complete all as specified and as directed. |
| 78 | M&L for Preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 79 | M&L for Preparation of old steel surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 80 | M&L for prepration of old steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint andapplying one coat of synthetic enamel paint complete all as specified and directed. |
| 81 | S&F for aluminium anodised XPM grill aluminium alloy DG 202 grill 4.8 mm thick (in the shape of expanded metal of aluminium XPM jalli) opening size 59mm (length expansion) and 45 mm (width expansion) fixed in and including E/H frame all as per manufacturers instruction and as directed. |
| 82 | M&L for preparation and removal of loose and disintegrated concrete of column, edges of slabs and edges of chhaja by low impact hammer including removal of debris outside MD land, Cleaning of surface with wire brush and apply approved epoxy based bonding coat on concrete surfaces to achieve sound bond between existing and new concrete. Application of complete treatment shall be through approved applicator all as per manufacturers instructions (Bauchemic, Krishna or Sunanda) complete all as specified and directed. |
| 83 | Taking down carefully copper/aluminium point wiring (light,fan socket or power ) point complete,including fixtures and fittings such as switches, ceiling rose, pendents, regulators, sockets, tube light fitting,main switch,MCB and DB's etc complete all as specified and directed. |
| 84 | M&L for point wiring complete with 1.5 sqmm PVC insulated, FRLSH type, ISI marked 1100 volts grade, single core multistranded copper conductor cable drawn through and including PVC conduit medium grade 25 mm dia, ISI marked with conduit accessories concealed in wall/ceiling/roof/column/ beam etc. and with sunk pressed steel terminal boxes not less than 2mm thick and 50mm deep concealed in wall flush mounting and providing 3mm thick hylam laminated sheet top cover, ISI marked fixed by means of chromium plated scres and cup washers including 1.5 sqmm PVC insulated, unsheathed, FRLSH type, ISI marked, 1100 volts grade, single core multistranded copper conductor cable green in colour as continous earth wire connected one end to metalic body of luminaries/fan/sockets/ceiling rose and other end to common earth dilly complete all as specified and directed for one light point controlled by one switch.,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC casing and caping of size 20 mm width or above as required at site with all accessories such as Tee ,Corner, overlaping connector etc.along the suface of walls/roofs/ ceilings/floors etc including concealed PVC box for fixing of and including modular plate as per no of switch modules flush mounted suitable for fixing modular switches , sockets,fan regulators etc.including modular plate cover of required size with necessary stainless steel cadmium plated screws and including 1.5 Sqmm PVC insulated, multistranded, FRLSH type,unsheathed(Green colour),single core, copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade complete all as specified and directed for the following:-Note: Make for item no 1.00 to 3.00Make of Cable: KEI/Finolex/Havells or equivalent, Make of PVC Conduit: Precision/Pressfit/Modi or equivalent |
| 85 | One light point / fan point controlled by one switch. |
| 86 | One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board . |
| 87 | One 5 pin 6 amps socket point controlled by one 6 amps switch on same board . |
| 88 | All as per item No.2 above, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board. |
| 89 | Supply & fixing modular type switch 6 Amps ,1way,1 module. |
| 90 | Supply & fixing modular type switch 16 Amps ,1way,1 module . |
| 91 | Supply & fixing modular type socket 6 Amps, 2/3 Pin combined 2 module . |
| 92 | Supply & fixing modular type socket 6 A/16 Amps, 6 Pin combined 2 module. |
| 93 | Supply & fix ceiling rose, 3 terminal ,PVC/polycarbonate body |
| 94 | Supply &fix modular type fan regulator stepped type 120 W- 2 module. |
| 95 | Taking down existing light fitting, of any type/make complete bipin holder,starter, connector etc and fixing back in existing or other place by providing PVC square box -02 Nos,tube rod and adequate length of three core flexible copper cable 0.75 sqmm from ceiling rose to fitting. |
| 96 | Supply and fixing LED lights fitting 1x 22W, 220V, 4' long AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.Make: Bajaj/Philips/Crompton or equivalent |
| 97 | Supply and fix LED tube light (2 feet) along with fixture,10 watts complete all as specified and directed.Make: Bajaj/Philips/Crompton or equivalent |
| 98 | Supply and fixing in repairs LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with all accessories and necessary fixing arrangement on wall at any height including three core 0.5 sqmm copper cable from connector to fitting and removing old unserviceable item complete all as specified and directed. Make: Bajaj/Orient Electric/Crompton or equivalent |
| 99 | Supply and fix in repairs GI bracket pipe of size 32 mm dia medium grade of 1.2 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces. The bracket pipe shall be welded to the MS strip of size 32mmX 5mm thick at three places for purpose of giving strengthening to the bracket pipe and fixing with necessary suitable nuts,bolts & washers and removing of old unserviceable item complete all as specified and directed. Make of GI Pipe : Jindal/Tata/Prakash or equivalent |
| 100 | Taking down ceiling fan/exhaust from its position for servicing, repairing, rewinding, painting and refixing the same after repair and replacement of all unserviceable parts thereof complete all as specified and directed. |
| 101 | Supply and fix in repair, factory made, SPN DB's, 08 way 240 volts, AC, double door, painted with epoxy based powder coated suitable for mounting MCB SP /DP and complete with and including 200 amps rated copper busbar, neutral bar,earth bar, connecting cable links with and including top and bottom removable gland plate, complete with IP 43 protection, all as specified and as directed.Make: Legrand/ Indo Asian/L&T or equivalent |
| 102 | Supply & fix for MCB SP 6 to 32 Amps 10 KA,\\"C\\" series complete all as specified and directed. Make: L&T/Legrand/Indo Asian or equivalent |
| 103 | Supply & fix MCB DP 32 Amps 10 KA,\\"C\\" series complete all as specified and directed. Make: L&T/Legrand/Indo Asian or equivalent |
| 104 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sq. mm. 2 core etc compete all as specified and directed.Make: KEI/Polycab/Havells or equivalent |
| 105 | Excavation in trenches , not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in any type of soil complete all as specified and directed. |
| 106 | Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed |
| 107 | Removing excavated soil not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed |
| 108 | Supply and laying DWC pipe 50 mm (ID) all as specified and directed.Make: Astral/Finolex/Supreme or equivalent |
| 109 | M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion. |
| 110 | SITC of water purifier RO+UV+UF+TD+Alkaline, UV LED light in storge tank, zero water wastage technology, multiple purification process, wall mounted Suitable for Purification of Brackish/Tap Water/Municipal Corporation Water, 20 LPH, Storage capacity 8 ltrs, total power consumption 60 watts, body material ABS food grade plastic including fixing/ mounting accesories (3 Year extended free services after 1 year warranty), complete all as specified and directed. Make: Kent/Aquaguard/Ao Smith or equivalent |
| 111 | SITC of electric water heater, storage type of 25 ltrs storage capacity steel body, heating element upto 2 KW, titanuim enamel coated heating element and tank for protection against corrosion, compression and high pressure, BEE 5 Star rated (10 year tank, 6 year element, and 4 year product warranty) complete with all accessories such as safety valve, thermostat, NRV and connection piece etc. complete all as specified and directed. Make: Bajaj/Racold/AO Smith or equivalent |
| 112 | S&F for PVC connections 15mm size with PTMT nuts of length 600mm completed all as specified and directed. |
| 113 | Supply and fix in repair integral LED aviation light luminaire complete with all accessories, prewired, Di-cast aluminium body, with UV stabilized plycarbonate red domes, IP-65, 180V to 220 V, more than 100000 hours LED life, 360 degree illumination, 302 LEDS, intensity more than 2000 MCD with necessary arrangement on Roof top at any height by adopting saftey precautions and including removing old unserviceable item complete all as specified and directed. Make: Bajaj/Phillips/wipro or equivalent Please Enable Macros to View BoQ information |
