Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Building Works (Civil) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soilDSR- 23/2.6.1 |
| 3 | Earth Work In Filling in Cartage up to 8K.M. SR |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR- 23/2.27 |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR- 23/4.1.8 |
| 6 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cumDSR- 23/5.33.1.1 |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum DSR- 23/5.33.2.1 |
| 8 | Centering and shuttering including strutting, propping etc. And removal of form for :Foundations, footings, bases of columns, etc. for mass concrete DSR- 23/5.9.1 |
| 9 | Centering and shuttering including strutting, propping etc. And removal of form for :Suspended floors, roofs, landings, balconies and access platform DSR- 23/5.9.3 |
| 10 | Centering and shuttering including strutting, propping etc. And removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR- 23/5.9.5 |
| 11 | Centering and shuttering including strutting, propping etc. And removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts DSR- 23/5.9.6 |
| 12 | Centering and shuttering including strutting, propping etc. And removal of form for :Weather shade, Chajjas, corbels etc., including edges DSR- 23/5.9.19 |
| 13 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) DSR- 23/4.10 |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) DSR- 23/6.1.2 |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)DSR- 23/6.4.2 |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement :3 coarse sand)DSR- 23/6.13.2 |
| 17 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry DSR- 23/6.15 |
| 18 | Providing and injecting chemical emulsion for Preconstructional antitermite treatment and creating a chemical barrier under and around the column pitswall trenches basement excavation top surface if plinth filling junction of wall and floor along the external perimer of binding expansion joints,surroundings of pipes and conduit etc. complete(Plinth area of the building at ground floor only shall be measuredas per I.S. 6313 (Part || 1981) Aldrine emulsifiable concentrate or any other approved material such as Hepthachlor or chlordance will be used. The rateof applications of chemical emulsion shall be as Follows :-(1) Treatment for Masonary & foundation 5 Liters per Sq.m.(2) Back fill in immediate contract with foundation 7.5 Litres per Sq.M.(3) Treatment of Top surface of plinth filling 5 Litres per Sq.M.(4) Treatment of soil along External Perimeter of Building 7.50 Litres per SAM.(5) Treatment of soil under Apron Along extral Perimeter 5 litres per sg.MSOR-2022/Ch. 8 Sch. 1 |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or moreDSR- 23/5.22.6 |
| 20 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sach and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm foe series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and inline sash adaptor (where ever required) of appropriate dimension, EPDm gasket , hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing haedware and drainage of water etc.After Fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof sillicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC Profiles to be as per design approved by Engineer-inCharge. Wire mesh/Glazing of plain/toughened/ laminated /double glass unit with / without high performance coatings as per design requirements and conforming to IS :3548 & IS : 16231 shall be paid separately. Notes:- Structural design proof cheacked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed >45 m/Sec as per IS 875 - Part 3. (ii) Sites with structure height more than 20m for all wind speeds.Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).DSR- 23/9.147.A4 |
| 21 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)DSR- 23/21.3.1 |
| 22 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sidesDSR- 23/10.29.2 |
| 23 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal woodDSR- 23/9.1.2 |
| 24 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood35 mm thick shuttersDSR- 23/9.5.1.1 |
| 25 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).DSR- 23/9.23 |
| 26 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thickDSR- 23/9.127.1 |
| 27 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).DSR- 23/9.53 |
| 28 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mmDSR- 23/9.96.1 |
| 29 | Providing and fixing aluminium tower bolts, ISI marked, powder coated (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc.complete : 250x10 mm.DSR- 23/9.97.2 |
| 30 | Providing and fixing aluminium handles, ISI marked, powder coated (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm.DSR- 23/9.100.1 |
| 31 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopperDSR- 23/9.101.2 |
| 32 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)DSR- 23/13.4.2 |
| 33 | 15 mm cement plaster on the rough side of single or half brick wall ofmix :1:6 (1 cement: 6 coarse sand)DSR- 23/13.5.2 |
| 34 | 6 MM CEMENT PLASTER of mix: 1:3 (1 cement : 3 fine sand) DSR- 23/13.16.1 |
| 35 | 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)DSR- 23/13.3.1 |
| 36 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Double Charge Size of Tile 600X600 mmDSR- 23/11.41.2 |
| 37 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with grey cement slurry @3.3kg/m including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm DSR- 23/11.46.2 |
| 38 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalentDSR- 23/11.56.1 |
| 39 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby redArea of slab over 0.50 sqmDSR- 23/8.2.2.2 |
| 40 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.DSR- 23/8.5 |
| 41 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite workDSR- 23/8.3.2 |
| 42 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.DSR- 23/11.37A |
| 43 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.DSR- 23/11.38 |
| 44 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litreDSR- 23/13.41.1 |
| 45 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqmDSR- 23/13.45.1 |
| 46 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete.DSR- 23/13.80 |
| 47 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in charge.8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.DSR- 23/12.58.1 |
| 48 | Providing and applying DRYTHANE 400HE with surface water proof coating 5mm including DRYTHANE standard 1mm thick including surface cleaning etc. all complete all area as per engineer inchargeSR |
| 49 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.DSR- 23/4.17 |
| 50 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksDSR- 23/10.25.2 |
| 51 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new workDSR- 23/13.61.1 |
| 52 | Internal and External Fittings and plumbing items |
| 53 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.DSR- 23/17.78 |
| 54 | Providing & fixing white vitreous china undercounter basin in white with C.I. brackets painted white, with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required.a)White 581mm x 402mm undercounter Wash basin size.MR |
| 55 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm diaDSR- 23/17.28.1.1 |
| 56 | Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.DSR- 23/17.31 |
| 57 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.DSR- 23/17.80 |
| 58 | Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shadeDSR- 23/8.10.2 |
| 59 | Providing and fixing unplasticised PVC connection pipe with brass unions.45 cm length15 mm nominal boreDSR- 23/18.21.2.1 |
| 60 | Providing and fixing Health faucet with white side spray, metal hose in polished chrome with flexible tube upto 1 metre long with S.S. triangular plate to European & Wall mount type W.C. of quality and make as approved by Engineer - in- charge.MR |
| 61 | Providing and fixing 2-way bib tap in polished chrome (kohler/Roca/ American standard)2-way bib tapMR |
| 62 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal boreDSR- 23/18.53.1 |
| 63 | Pillar tap in polished chrome Basin Mixer with Popup Waste System.MR |
| 64 | Providing and fixing 350mm bottle trap without drain in polished chrome of approved quality & make and as per the direction of Engineer-in-charge.MR |
| 65 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.17.71 |
| 66 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.DSR- 23/17.73.1 |
| 67 | Providing and Fixing Toilet Paper Holder:C.P. BrassDSR- 23/17.34.1 |
| 68 | Providing & fixing Cast Iron pipe soil, waste and vent pipes.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905a) 100mm dia centrifugally cast iron S & S pipe.DSR- 23/17.35.1.3 |
| 69 | Providing & fixing Cast Iron pipe soil, waste and vent pipes.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905b) 75mm dia centrifugally cast iron S & S pipe.DSR- 23/17.35.2.3 |
| 70 | Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. ( for wash basin waste )32mm dia nominal boreDSR- 23/18.10.4 |
| 71 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.SS 304 grade coupling with EPDM rubber gasket100 mmDSR- 23/17.57A.1.1 |
| 72 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.SS 304 grade coupling with EPDM rubber gasket75mmDSR- 23/17.57A.2.1 |
| 73 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size). Including cost of cutting holes & making good the walls etc.a) for 100mm dia pipe.DSR- 23/17.37.1 |
| 74 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size). Including cost of cutting holes & making good the walls etc.b) for 75mm dia pipe.DSR- 23/17.37.2 |
| 75 | Providing & fixing cast iron coller.100 mm diaDSR- 23/17.57.1.2 |
| 76 | Providing & fixing cast iron coller.75mm dia.DSR- 23/17.57.2.2 |
| 77 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :a) 100mm inlet & 100mm outlet.DSR- 23/17.60.1.3 |
| 78 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100mm inlet & 75mm outlet.DSR- 23/17.60.2.3 |
| 79 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.100mmDSR- 23/17.38.1.3 |
| 80 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.75mmDSR- 23/17.38.2.3 |
| 81 | Providing and fixing plain bend of required degree.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905100mmDSR- 23/17.39.1.3 |
| 82 | Providing and fixing plain bend of required degree.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:1590575mmDSR- 23/17.39.2.3 |
| 83 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100mmDSR- 23/17.43.1.2 |
| 84 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75x75x75mmDSR- 23/17.43.2.2 |
| 85 | Providing and fixing centrifugaly cast iron single equal plain junction of required degree.100x100x100mmDSR- 23/17.44.1.3 |
| 86 | Providing and fixing centrifugaly cast iron single equal plain junction of required degree.75x75x75mmDSR- 23/17.44.2.3 |
| 87 | Providing and fixing single unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :100x100x75mmDSR- 23/17.47.1.3 |
| 88 | Providing and fixing single unequal plain invert branch of required degree :100x100x75mmDSR- 23/17.52.1.3 |
| 89 | Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete :( c.o.p.)100mmDSR- 23/17.55.1.2 |
| 90 | Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete :( c.o.p.)75mmDSR- 23/17.55.2.2 |
| 91 | Providing and fixing cast iron terminal guard.100 mmDSR- 23/17.56.1.2 |
| 92 | Providing and fixing cast iron terminal guard.75 mmDSR- 23/17.56.2.2 |
| 93 | Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground)110 mm diaDSR- 23/19.2.1 |
| 94 | Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground)150 mm diaDSR- 23/19.2.1 |
| 95 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameterDSR- 23/12.41.2 |
| 96 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler110 mmDSR- 23/12.42.1.2 |
| 97 | Bend 87.5°110 mm bendDSR- 23/12.42.5.2 |
| 98 | Shoe (Plain) 110 mm ShoeDSR- 23/12.42.6.2 |
| 99 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mmDSR- 23/12.43.2 |
| 100 | Providing and fixing to the inlet mouth of rain water pipe cast irongrating 15 cm diameter and weighing not less than 440 grams.DSR- 23/12.44 |
| 101 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.DSR- 23/12.22 |
| 102 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15mm dia nominal outer dia pipesDSR- 23/18.8.1 |
| 103 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.20mm dia nominal outer dia pipesDSR- 23/18.8.2 |
| 104 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.25mm dia nominal outer dia pipesDSR- 23/18.8.3 |
| 105 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall20mm dia nominal boreDSR- 23/18.7.2 |
| 106 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall25mm dia nominal boreDSR- 23/18.7.3 |
| 107 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall32mm dia nominal boreDSR- 23/18.7.4 |
| 108 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall40mm dia nominal boreDSR- 23/18.7.5 |
| 109 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work32 mm nominal dia PipesDSR- 23/18.9.4 |
| 110 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work40 mm nominal dia PipesDSR- 23/18.9.5 |
| 111 | Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia nominal boreDSR- 23/18.7.1 |
| 112 | Providing and fixing gun metal gate valve with wheel of approved quality.32mm dia nominal boreDSR- 23/18.17.2 |
| 113 | Providing and fixing gun metal gate valve with wheel of approved quality.40mm dia nominal boreDSR- 23/18.17.2 |
| 114 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal boreDSR- 23/18.18.3 |
| 115 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.DSR- 23/18.48 |
| 116 | Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.1.50 m depthPipes 80 mm to 300 mm diameterDSR- 23/2.10.1.2 |
| 117 | Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 150 mm. dia. RCC PipesDSR- 23/19.6.2 |
| 118 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design150 mm. dia.DSR- 23/19.3.2 |
| 119 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design.Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With common burnt clay FPS (non modular) bricks of class designation 7.5DSR- 23/19.7.1.1 |
| 120 | Extra for depth for manholes:Size 90x80cm with With common burnt clay FPS (non modular) bricks of class designation 7.5DSR- 23/19.8.1.1 |
| 121 | Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR- 23/19.7.2.1 |
| 122 | Extra for depth for manholes :Size 120x90 cmWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR- 23/19.8.2.1 |
| 123 | Renovation of Existing Library Building |
| 124 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.DSR- 23/15.3 |
| 125 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge.DSR- 23/15.5 |
| 126 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortarDSR- 23/15.7.4 |
| 127 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):From brick work in cement mortarDSR- 23/15.8.3 |
| 128 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and belowDSR- 23/15.21.1 |
| 129 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mmDSR- 23/15.23.1 |
| 130 | Dismantling existing plaster including disposal of refuse as directed by Engineer-in-charge with in a distance of 60 mt (200 feet)SOR- 2025/706 |
| 131 | Scraping old white or colour wash including disposal of refuse material as directed by Engineer-in-charge with a distance of 60 metre (200 feet)SOR- 2025/708 |
| 132 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cumDSR- 23/5.33.2.1 |
| 133 | Centering and shuttering including strutting, propping etc. And removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantileversDSR- 23/5.9.5 |
| 134 | Centering and shuttering including strutting, propping etc. And removal of form for :Weather shade, Chajjas, corbels etc., including edgesDSR- 23/5.9.9 |
| 135 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo mechanically treated bars of grade fe-500D or more.DSR- 23/5.22A.6 |
| 136 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sach and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm foe series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and inline sash adaptor (where ever required) of appropriate dimension, EPDm gasket , hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing haedware and drainage of water etc.After Fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof sillicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC Profiles to be as per design approved by Engineer-inCharge. Wire mesh/Glazing of plain/toughened/ laminated /double glass unit with / without high performance coatings as per design requirements and conforming to IS :3548 & IS : 16231 shall be paid separately. Notes:- Structural design proof cheacked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed >45 m/Sec as per IS 875 - Part 3. (ii) Sites with structure height more than 20m for all wind speeds.Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8 m).DSR- 23/9.147.A4 |
| 137 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)DSR- 23/21.3.1 |
| 138 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sidesDSR- 23/10.29.2 |
| 139 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood35 mm thick shuttersDSR- 23/9.5.1.1 |
| 140 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).DSR- 23/9.23 |
| 141 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thickDSR- 23/9.127.1 |
| 142 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).DSR- 23/9.53 |
| 143 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mmDSR- 23/9.96.1 |
| 144 | Providing and fixing aluminium tower bolts, ISI marked, powder coated (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc.complete : 250x10 mm.DSR- 23/9.97.2 |
| 145 | Providing and fixing aluminium handles, ISI marked, powder coated (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm.DSR- 23/9.100.1 |
| 146 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopperDSR- 23/9.101.2 |
| 147 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)DSR- 23/13.4.2 |
| 148 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)DSR- 23/13.5.2 |
| 149 | 6 MM CEMENT PLASTER of mix: 1:3 (1 cement : 3 fine sand) DSR- 23/13.16.1 |
| 150 | 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)DSR- 23/13.3.1 |
| 151 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Double Charge Size of Tile 600X600 mmDSR- 23/11.41.2 |
| 152 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with grey cement slurry @3.3kg/m including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm DSR- 23/111.46.2 |
| 153 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalentDSR- 23/11.56.1 |
| 154 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite workDSR- 23/8.3.2 |
| 155 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.DSR- 23/11.37A |
| 156 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.DSR- 23/11.38 |
| 157 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litreDSR- 23/13.41 |
| 158 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqmDSR- 23/13.45.1 |
| 159 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete.DSR- 23/13.80 |
| 160 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in charge.8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.DSR- 23/12.58.1 |
| 161 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new workDSR- 23/13.61.1 |
| 162 | Providing and applying DRYTHANE 400HE with surface water proof coating 5mm including DRYTHANE standard 1mm thick including surface cleaning etc. all complete all area as per engineer inchargeSR |
| 163 | Borewell and Rain water Harvesting |
| 164 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil350 mm diaDSR- 23/23.1.1.2 |
| 165 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (RMS) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.150mm nominal size diaDSR- 23/23.4.2 |
| 166 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.DSR- 23/23.8 |
| 167 | Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS:8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.150 mm nominal size diaDSR- 23/23.11.2 |
| 168 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.DSR- 23/23.12 |
| 169 | Supplying & Installation of suitable Hp submersible pump B.S or K.S.B or equivalent make with finolex cable 1x3x2.5 squmm(upto 75mtr) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as MCB of 0-25Amp (Havell or Indocopp or MDS make), Volt & Ampere meter (AE make), single phase preventer (Minilac or VSP -1 make) starter (L&T or BCH make) etc of approved make, 40mm HDPE Pipe (25 mtr) and all accessories complete as per requirement of site.NOTESa) Contractor shall include the rate of electrical control panels complete with all accessories &controls, all Electrical/Mechanical items as required to operate the system automatic/manual.b) Contractor to select suitable 3 HP of pumps .c) Level Controller with sufficient nos. of low / high level alarms, contacts with electrodes and control wiring for the automatic operation of water supply pumps, Submersible Sump Pumps, to achieve the functional requirement shall be provided. Control wiring between these pumps and water tanks shall be provided.Domestic water pumps must start at low water level in overhead domestic water tank & stop at high level in that water tank. Dry running protection shall be provided for all the pumps.Sequencing shall be provided for each set of pumps.MR |
| 170 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge.a) All kinds of soilDSR- 23/2.6.1 |
| 171 | Supplying, filling, spreading & leveling stone boulders of size range 5 mm to 20mm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in- charge.DSR- 23/23.5 |
| 172 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.DSR- 23/23.7 |
| 173 | Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering complete. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources)DSR- 23/4.5.1 |
| 174 | Drain |
| 175 | Excavation in foundation in ordinary Soil ( Loam clay or sand ) including filling lift upto 1.5metre (5fts.) and lead upto 30.0 m (100 fts.) & including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in- charge upto a distance of 30 M. (100 fts.) from the foundation trenches.SOR 2025/251 |
| 176 | Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation.SOR 2025/281 Sl. no. 6(1) |
| 177 | Mild Steel or iron in plain work such as in reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastages and over lapping and hookes.SOR 2025/ 504 |
| 178 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland /portland Slag cement, admixtures in recommended proportions as per iS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth levelConcrete of m25 grade with minimum cement content of 330 kg /cumDSR- 23/5.33.1.1 |
| 179 | Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concreteDSR- 23/5.9.1 |
| 180 | Centering and shuttering including strutting, propping etc. and removal of form forWalls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.DSR- 23/5.9.2 |
| 181 | Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platformDSR- 23/5.9.3 |
| 182 | Pathway (Paver Block) |
| 183 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge:All kinds of soilDSR- 23/2.1.1 |
| 184 | Proving and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to planth leve: 1:4:8 (1 cement:4 coarse sand (zone-II) derivedfrom natural source : 8 graded stone aggregate 40 mm nominal size derivedd from natural sources)DSR- 23/4.1.8 |
| 185 | Providing and laying factory made cobble shape paver block 80 mm thick, compressive strength >= M 50 steel mould compressive technolgy.SR |
| 186 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).DSR- 23/16.69 |
| 187 | HORTICULTURE |
| 188 | Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-incharge.DSR (H&L) 2020/ 6.12 |
| 189 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same and maintenance for 30 days or more till the grass establish properly, as per direction of the officer in chargeDSR (H&L) 2020/ 2.34 |
| 190 | Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. DSR (H&L) 2020/ 7.70 |
| 191 | Electrical Work |
| 192 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C DSR (E&M) 2022- 1.10.3 |
| 193 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.DSR (E&M) 2022- 1.11 |
| 194 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mmDSR (E&M) 2022- 1.21.2 |
| 195 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switchDSR (E&M) 2022- 1.24.1 |
| 196 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.DSR (E&M) 2022- 1.31 |
| 197 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.DSR (E&M) 2022- 1.25 |
| 198 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm)DSR (E&M) 2022- 1.27.1 |
| 199 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.3 module with GI box(100mmx75mm)DSR (E&M) 2022- 1.27.2 |
| 200 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.4 module with GI box(125mmx75mm)DSR (E&M) 2022- 1.27.3 |
| 201 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.6 module with GI box(200mmx75mm)DSR (E&M) 2022- 1.27.4 |
| 202 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.8 module with GI box(125mmx125mm) DSR (E&M) 2022- 1.27.5 |
| 203 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.12 module with GI box(200mmx150mm) DSR (E&M) 2022- 1.27.6 |
| 204 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16A modular socket outlet and 15/16 A modular switch, connections etc. as required.DSR (E&M) 2022- 1.32 |
| 205 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required.DSR (E&M) 2022- 1.57 |
| 206 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wireDSR (E&M) 2022- 1.14.1 |
| 207 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (circuit for Powe point looping )DSR (E&M) 2022- 1.14.2 |
| 208 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire( circuit for power point) DSR (E&M) 2022- 1.14.3 |
| 209 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire (Submain for DB)DSR (E&M) 2022- 1.14.5 |
| 210 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 16 sq. mm + 2 X 6 sq. mm earth wireDSR (E&M) 2022- 1.14.6 |
| 211 | Supply and fixing of recess/Surface/Pendent mounting round 6Watt 8 Watt LED Down Lighter having Powder coated die castaluminium housing with heat sink, diffuser/ Reflector and driver pleasing aesthetic look. Complete in all respectSOR 22/ 1401 |
| 212 | Supply and fixing of LED Street light Fitting having die castaluminium body and diffuser with driver set suitable for 110 to130 Watt. Confirming to IP 65 and above Protection completein all respect.SOR 22/1424 |
| 213 | Supply of 15W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. SOR 22/1402 |
| 214 | Supply and fixing of LED Tube Light with batten suitable for upto 1 X 22 watt LED tube light complete including tube etc onsurface complete in all respect. CAT-AAASOR 22/1413 |
| 215 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double doorDSR (E&M) 2022- 2.4.3 |
| 216 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single poleDSR (E&M) 2022- 2.10.1 |
| 217 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double poleDSR (E&M) 2022- 2.10.3 |
| 218 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutralDSR (E&M) 2022- 2.10.5 |
| 219 | S&F and making connection of 63A 2 pole 30mA ELCB/RCCB of Din Rail Mounting complete in all respect as per direction and satisfaction to the Engineer in charge. SOR 22/394 |
| 220 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required. DSR (E&M) 2022- 5.4 |
| 221 | Providing and fixing 25 mm X 5 mm G.I. strip on surface orin recess for connections etc. as required.DSR (E&M) 2022- 5.15 |
| 222 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of750 mm below ground level over a cushion of 75 mm. thick sand allaround and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the 4CORE X 16 SQMM AL.AR.XLPE CableSOR 22/501/(i) |
| 223 | Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument.chamber etc. complete in all respects. The instrument chamber shall be.separate and shall comprise of flush type ammeter, voltmerer, selector.switches for ammeter and voltmeter, instrument fuses, current transormer etc.The board shall have suitable capacity electroytic alumininum busbars as perIS8623 istulate with heat shrink sleeving and mountend on non hygroscopic.supports such as CMC/DMC support with deteachable side covers and shall.be suitable for extension on the sides. The switches shall be complete with.suitable cable end boxes, reverse entery boxes in case of pedestaal type,.cable sockets, compression glands and indicating lamp on incoming etc..The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided withampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimumthickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B--100 Amp. TPN-1 No and 63 Amp. TPN-3 Nos.SOR 22/802/C |
| 224 | S&F of 0.5 Amp to 5 Amp. 4 pole MCB (10 KA) C Curve CAT-A, these materials to be install in above panelSOR 22/1018 |
| 225 | S&F of 0.5 Amp. to 5 Amp. DP MCB (10 KA) C Curve CAT-A, these materials to be install in above panelSOR 22/1008 |
| 226 | SITC of 2 ton split AC including 2 years mentainence Power Supply: 230V, 50 Hz, single phase. Vendor should supply suitable rating external voltage stabilizer even if the AC is capable of operating with wide voltage range. Piping: 6 metres each of the insulated copper refrigerant pipings(suction and return line), 6 meters of eleBtrical cable and 6 meters of PVC drain piping with each AC system. Accessories: Mounting bracket for indoor unit, Heavy duty Stand for installing outdoor condenser unit on the roof or on the wall as required with serrated anti-vibration pads. Power and control cables of copper Warranty: Minimum 1 year on the whole machine and minimum 5 years on the compressor from the date of satisfactory installation, commissioning and acceptance of the AC unit Makes: Carrier/ Voltas /Blue star/ LG/Daikin/Hitachi/Mitsubishi/Panasonic /Samsung/HavellsMR |
| 227 | Computer & CCTV |
| 228 | IP Bullet Outdoor Camera: UL Listed 2-2.5 Megapixel CMOS 1/2.8\\"Progressive Scan CMOS, 2592 x 1944 @20fps, with Motorized vari-focal (2.8 - 12mm), 0.01 Lux at F1.2, ICR, support H.264 & H.265, 120dB Wide Dynamic Range, BLC, 3D Digital Noise Reduction, Third stream configurable stream, 12 VDC & PoE , IR range: 50m, Support on-board storage up to 128 GB, IP67 with IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Parking detection, Motion detection, video tampering, ONVIF (PROFILE S & G) BIS, CE, FCC, UL certified.MR |
| 229 | Recording servers: 64channel Smart Network Video Recorder, Should support N+1, Hot spare, Up to 12 Megapixels Resolution, two independent HDMI and one VGA Output , Support H.265, H.264, MJPEG, 64 IP cameras can be connected with( 384M+384M) incoming & outgoing bandwidth, Support HDD hot swap with RAID 0,1,5,10 storage scheme configurable, ANR Technology, 8 SATA interfaces for HDDs and capacity of each HDD upto 10TB, 3x USB with two USB 3.0, Alarm I/O 16/8, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Redundant Power Supply, Multiple network monitoring: Web viewer, BIS, CE, FCC, UL certified.MR |
| 230 | LPR CMS for comprehensive with Software application to export the report of full Image and excel format log access reporting, Web API integration etc.CPU: Intel, 8GB RAM, 4TB HDD Storage, OS: Linux, TCP/IP Communication, Number of cameras integration: Image of Camera, upto 64 cameras, further can be extended with license as per the requirement. MR |
| 231 | 0TB Special Enterprise Hard Disk. MR |
| 232 | 43\\" Full HD LED TV Color Monitor Commercial Grade 24x7 with accessories.MR |
| 233 | Supply and fixing of i7 proccesure CPU with 20 inch LED/LCD monitor including 12 th gen./8gb/1TB SSD hard disc. 1Year Warranty.MR |
| 234 | 24 Port Managed PoE Layer-2 switch 10/100/1000 Base-T ports + 2x1G SFP ports, minimum 180 W MR |
| 235 | Supply, Installation, Testing and Commissioning of SFP Module for poe SwitchMR |
| 236 | Supply and fixing of 10 way Double Door TPN DB incloser with 1nos 63 A TPN MCB,3NOS 40A RCCB,24 NOS SP MCBMR |
| 237 | Supply, installation, Testing and commissioning of UPS as per specifications and complete in all respects.10 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic Current THD 3% typical at 100% load, 6% maximum at 50% load with Isolation Transformer and 30 min battery backup for each UPS along with battery cabinet complete in all respect including supporting steel structure for UPS and Battery as required. MR |
| 238 | Supply & laying of Cat 6 unarmoured cable, 4 pair, 23 AWG, UTPMR |
| 239 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. DSR-2022/1.21.2 |
| 240 | Supply & laying of HDPE Duct 40mm including digging and refilling. MR |
| 241 | 6 Port LIU Multimode LoadedMR |
| 242 | Pig Tails, SC-LC Fiber patch cord with splicingMR |
| 243 | Supply, Installation, Testing and Commissioning of Outdoor Rack / Metal Box including 5 Amp. PDU Unit 1NO for 2 nos Camera.MR |
| 244 | Supply and fixing of 6 mtr octagonal pole base dia 170mm and top dia 120mm the thickness of pole including all acessuries and RCC foundation.MR |
| 245 | Supply and fixing of i7 proccesure CPU with 20 inch LED/LCD monitor including 12 th gen./8gb/1TB SSD hard disc. 1Year Warranty.MR |
| 246 | AMC of all system for 2years after handing over the all system @ 10% of total cost |
| 247 | Furniture & Shelves |
| 248 | Reception tableDimension(L) 2200mm X (D)750mmX (H) 750mm (all over ht 1050mm)Supplying, and placing in position of reception Table as per Image/drawing. The table top made up of 36mm thick pre-laminated particle board and understructure shall be made of 25mm thick prelaminated particie board with 2mm thik pvc edge dge banding. Modesty & side panel shall be 25mm thick prelam particle board with 2mm thick pvc edge banding Table top height will be 750mm from the floor level & one additional top at the height of 300 mm above the table top rest on SS stud/prelam vertical panel. overall ht of the table 1050mm. The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of Prelam particle board Mobile pedestal of size 400mm(L)x 450mm(D)x600mm(HT) (2 drawer filling). Pedestal Top made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue.MR |
| 249 | ChairSupplying and placing in position of medium back 360° degree revolving chair all over size is: 610mm (L) x 470mm (D) x 1040mm (h) as per image. The chair made of full mesh in black colour it will comes in matte finish in contemporary style. Arms: armrest is having two adjustment heights (up & down).use of ply: 12 mm thick hot pressed bwr plywood (is grade-303 for seat) seat: 40 mm thick polyurethane foam with density 32 kg per cu meter for best quality cushioning in seat, back frame of design shall be curved made of two pieces Injection moulded frame cover with mesh backrest support adjustable lumbar support, mechanism: self weighted multi locking mechanism, gas lift 100 mm telescopic haudraulic base: 650 mm chrome base with smooth castors.MR |
| 250 | SofaSupplying, and placing in position of sofa as per Image classic Contemporary design and slender curves.. The Sofa of stands Firm on solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Leatherette, the sofa makes a fantastic first impression. The Cushioning is moulded such that it flows along the partition for a clean unified look, steam beech solid wood have used for framing construction of sofa The seat cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. The backrest has a foam of 28kg/m3 with polyester poly fill outer layer of 200 gsm. The polyester poly fill keeps the upholstery wrinkle free & soft.3 seater(W)1905mm X (D)890mm X (H)870mmMR |
| 251 | SofaSupplying, and placing in position of sofa as per Image classic Contemporary design and slender curves.. The Sofa of stands Firm on solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Leatherette, the sofa makes a fantastic first impression. The Cushioning is moulded such that it flows along the partition for a clean unified look, steam beech solid wood have used for framing construction of sofa The seat cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. The backrest has a foam of 28kg/m3 with polyester poly fill outer layer of 200 gsm. The polyester poly fill keeps the upholstery wrinkle free & soft.2 seater: (W)1410mm X (D)890mm X (H)870mmMR |
| 252 | Side tableSupplying and placing in position of Side table as per image., the collection is destined to become a centerpiece of your modent Indian homes. Perthing on solid wood trestle legs, the veneer tabletop is tastefully adormed with a brick pattern, crafted to perfection by skilled Marquetry artisan Material & Subtype: Veneer/Solid Wood-Stram Beech Wood. Leg Material:Solid Wood, Finish: Matte Colour & Colour FamilyBrown Wenge.Dimension (W650mm X (D500mm X (460mm)MR |
| 253 | Reading hall tableSupplying, and placing in position of table as per image/drawing. The Table top made out of 25mm the prelam particle board with 2mm thik pvc edge banding with ms powder coated \\"C\\" shape legs of size: 50mm x 50mm.Comprising of metal powder coated cross connectors of size 40mm X 25mm. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glueDimension (W)8890mm X (D) 1530mm X (H) 750mmMR |
| 254 | Reading hall tableSupplying, and placing in position of table as per image/drawing. The Table top made out of 25mm the prelam particle board with 2mm thik pvc edge banding with ms powder coated \\"C\\" shape legs of size: 50mm x 50mm.Comprising of metal powder coated cross connectors of size 40mm X 25mm. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glueDimension: (W)7480mm X (D) 1530mm X (H) 750mmMR |
| 255 | Reading hall tableSupplying, and placing in position of table as per image/drawing. The Table top made out of 25mm the prelam particle board with 2mm thik pvc edge banding with ms powder coated \\"C\\" shape legs of size: 50mm x 50mm.Comprising of metal powder coated cross connectors of size 40mm X 25mm. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glueDimension (W) 6000mm x (D) 1530mm X (H) 750mmMR |
| 256 | Reading hall tableSupplying, and placing in position of table as per image/drawing. The Table top made out of 25mm the prelam particle board with 2mm thik pvc edge banding with ms powder coated \\"C\\" shape legs of size: 50mm x 50mm.Comprising of metal powder coated cross connectors of size 40mm X 25mm. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glueDimension (W) 6700mm X (D) 1530mm x (H) 750mmmMR |
| 257 | Reading hall tableSupplying, and placing in position of table as per image/drawing. The Table top made out of 25mm the prelam particle board with 2mm thik pvc edge banding with ms powder coated \\"C\\" shape legs of size: 50mm x 50mm.Comprising of metal powder coated cross connectors of size 40mm X 25mm. All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glueDimension (W) 3000mm x (D) 1530mm x (H) 750mmMR |
| 258 | ChairSupplying and placing in position of fix cantilever chair all over size is: 500mm(L) 530mm(d)x 840mm(h) as per image. The chair made of full leatherette in black colour. It will comes in matte finish in contemporary style arms: padded armrest. Use of ply: seat & back plywood made of 12 mm hot pressed. Seat: 40 mm thick polyurethane foam with density 32 kg per cu meter for best quality cushioning in seat, back: 40 mm. thick polyurethane foam with density 32 kg per cu meter for best quality cushioning in back Backrest support foam design based on symmetrical lumbar support, base: four chrome legs.MR |
| 259 | Full height storage for Shelf roomSupplying, and placing in position of full height storage 1800mm height as per photograph/drawing. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.Dimension: (W) 3500mm X (0) 450mm x (H) 1800mmMR |
| 260 | Full height storage for Shelf roomSupplying, and placing in position of full height storage 1800mm height as per photograph/drawing. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.Dimension (W) 3400mm X (D) 450mm x (H) 1800mmMR |
| 261 | Full height storage for Shelf roomSupplying, and placing in position of full height storage 1800mm height as per photograph/drawing. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.Dimension: (W) 11000mm X (0) 450mm x (H) 1000mmMR |
| 262 | Digital Standee (Kiosk) |
| 263 | Supply Installation Testing and Commissioning of MS Standee with White Powder Coated with 55-Inch Commercial Display:1. Standee Display (Display Make: Panasonic/LG/Samsung): Size: 55 inches (diagonal), Aspect Ratio: 16:9, Resolution: Full HD (1920 × 1080),Brightness: 400 nits (suitable for indoor/semi-indoor use), Operation: 24x7, Orientation: Portrait (default for standee), can support landscape if required, Input Ports: HDMI, DVI-D, DisplayPort, USB, RS232/LAN for control.2. Standee Enclosure Construction Material: MS Steel (1.2–1.5 mm thick) CRCA sheet with powder-coated finish,Option: Stainless Steel (SS304) for premium or outdoor use, Surface Finish:Matt or Glossy powder coating (custom RAL colors),Anti-scratch, rust-proof, UV-resistant finish, Glass Protection:5 mm Toughened Glass with Anti-Glare / Anti-UV coating, Design:Slim bezel cut-out to align with 55-inch display screen area,Rounded edges for premium aesthetics, Branding space (vinyl/UV print) on front fascia or base panel.3. Mechanical & Dimensions: Outer Dimension (approx.): Height: 1900–2000 mm, Width: 750–800 mm, Depth: 70–120 mm, Base Stand:Heavy-duty base plate with concealed wheels (optional), Anchoring provision for permanent installation, 4. Access & Maintenance: Rear lockable service door with key-based access, Removable side/back panels for easy servicing, Cooling & Ventilation: Industrial-grade axial fans with dust filters, Option: Thermostat-based cooling system, Ventilation slots concealed at top/bottom for airflow, Option for AC cooling module for outdoor/hotenvironments,5. Electrical & Power: Input Power: 100–240V AC, 50/60Hz, Internal Power Management: Industrial-grade SMPS,Surge Protection (5–10 kVA recommended),Cable Management: Concealed routing with IEC connectors.6. Media Player Integration (Optional) Space for Navori, BrightSign, Android, or Windows media player,Internal mounting brackets with ventilation, Provision for external USB/HDMI access7. Safety & Security:Lockable enclosure with tamper-proof screws, Shatter-resistant toughened glass, Overvoltage, over-current, and short-circuit protection8. Additional Features:Branding area (top header / bottom fascia), Interactive option: IR Touch / PCAP Touch Overlay (upgradeable),Sensor integration: Motion, temperature, ambient light (optional), Wheels with lock (for mobility) Supply Installation Testing and Commissioning of Signage Software MR Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
