|
| 1 | Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 2 | Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. |
| 3 | M & L anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 4 | M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators, Partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 5 | M&L for powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100 mm long (2 no.) suitable handle (1 no.) complete all as specifiedcomplete all as specified and directed. |
| 6 | S &F 4.8mm thick tinted glass ordinary quality and fixed in aluminium beads in sqaures not exc 0.5 sqm in each pane complete all as specified and directed. |
| 7 | S&F Galvanised mild steel cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples in window or door complete all as specified and as directed. |
| 8 | S & F 4mm thick figured glass pin head type and glazing with silicon in sqaures not exc 0.5 sqm in each pane complete all as specified and directed. |
| 9 | S & F for Solid wood grain printed PVC sheet door frame of size 50mm x 95mm made by joining 3nos. Heat bent PVC Sheet `C' Channel of 5mm thickness of sizes 35mm x 30mm x 25mm & 40mm x 35mm x40mm & 25mm x 30mm x 35mm using solvent cement. The two side `C' Channel shall be reinforced with M.S. tube of size 19mm x 19mm. All the three `C' channel Shall be fixed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitre cut at two corners and joined by inserting 4nos. 150mm long brackets of 15x15mm M.S. Square tube inside the 19mm x 19mm square tubes & remain each of then with four screws as indicated in the drawing complete all as specified and directed. |
| 10 | S&F for 35 mm thick Factory made solid EPS core PVC Moulded Door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design, consisting of frame made out of MS tube 20 mm x 40 mm. The core panel shall consist of 25 mm thick high density EPS routed with design, sandwitched in between front side moulded prelam 2 mm thick Moulded PVC sheet on one face and 2 mm PVC sheet on other side. The shutter on all edges to be sealed with lipping of 10 mm (5mm x 2) thick x 25 mm wide PVC sheet on other side & 60 mm wide PVC sheet for lock lock rail side . the lipping shall be bonded to the 2 mm moulded / plain PVC sheet with solvant cement asas specified and shown in SSR and Particular specification & as directed by Engineer-in-charge.Note :- The PVC doors shall be fixed as per manufacturer's instructions and as directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
| 11 | S&F for 35 mm thick Factory made solid EPS core PVC Moulded Door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design, consisting of frame made out of MS tube 20 mm x 40 mm. The core panel shall consist of 25 mm thick high density EPS routed with design, sandwitched in between front side moulded prelam 2 mm thick Moulded PVC sheet on one face and 2 mm PVC sheet on other side. The shutter on all edges to be sealed with lipping of 10 mm (5mm x 2) thick x 25 mm wide PVC sheet on other side & 60 mm wide PVC sheet for lock lock rail side . the lipping shall be bonded to the 2 mm moulded / plain PVC sheet with solvant cement asas specified and shown in SSR and Particular specification & as directed by Engineer-in-charge.Note :- The PVC doors shall be fixed as per manufacturer's instructions and as directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
