|
| 1 | Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed. |
| 4 | Taking down cement plaster on brick work or stone walls, etc including wall tiles, raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 5 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 6 | Demolition of pre-cast concrete block masonry built in cement mortar of any description in any position complete all as specified and directed. |
| 7 | M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) (using 20mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed. |
| 8 | Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as spcified and directed. (Make Approved By GE) |
| 9 | All as above but on vertical surface as in skirting/Dados over 10 mm thick plaster cm 1:4 complete all as specified and directed. |
| 10 | M&L Virified Ceramic tiles Dark shade 8 to 9 mm thick (square/rectangular) polished/Matt/Glossy, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors & Vertical surface etc. set and jointed in epoxy grout and including tile adhesive chemical backing coat complete all as spcified and directed. |
| 11 | M&L for vitrified tiles Fullbody 8 mm thick, light shade (square/rectangular) polished/Matt/Glossy, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 12 | M&L for vitrified tiles Fullbody 8 mm thick, light shade (square/rectangular) polished/Matt/Glossy on vertical surfaces such as skirtings, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10 mm thick rendering in cement mortar 1:3 complete all as specified and directed. |
| 13 | M & L for glazed coloured white tiles of size 450x300x 7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete all as specified and directed. |
| 14 | S&F for 30 mm thick 2nd class hardwood factory made plain framed panelled shutters (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 15 | M & L for 30 mm thick glazed and skeleton shutters of 2nd class Hard Wood(Not less than Hollock wood) local made shutter, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed. |
| 16 | S&F for Solid PVC door frame of size 50 mm x 47 mm made out of 15 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per spacification & drawing shown in SSR Part-II, complete all as specified and directed. |
| 17 | M&L for made soild panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in SSR Part- II, complete all as specified and directed. |
| 18 | S&F 30 mm thick flush shutters,solid core construction,with partical board core and covered with decorative face veneer with lipping/frame to match on both sidescomplete all as specified and directed. |
| 19 | S&F 100 mm stainless steel extruded (ISI Marked ) butt hinges complete all as specified and directed. |
| 20 | S&F for 75mm stainless steel extruded (ISI Marked ) butt hinges complete all as specified and directed. |
| 21 | S&F for 150mm size aluminium anodised, barrel tower bolts, of extruded section and fixed complete all as specified and directed. |
| 22 | S&F for 100mm size aluminium anodised, barrel tower bolts, of extruded section and fixed complete all as specified and directed. |
| 23 | S&F for 150mm size Handles extruded aluminium alloy handles,fabricated type anodised complete all as specified and directed. |
| 24 | S&F for 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 25 | S&F in repair 4 mm thick Plain sheet glass, ordinary quality and glazing with oil putty/ beading in square exc. 0.5 sqm in each pane, complete all as specified and directed. |
| 26 | S&F in repair for 4 mm thick figured glass, pin headed type and glazing with oil putty/beading in squares n exc 0.5 sqm in each pane, complete all as specified and directed. |
| 27 | Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. |
| 28 | S&F for Galvanised stainless steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm, complete all as specified and directed. |
| 29 | S&F in repair Galvanised stainless steell wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm, complete all as specified and directed. |
| 30 | M&L for 15mm thick rendering on fair faces to brick work or stone masonry surface in CM 1:6 finished the surface even and smooth (without using extra cement on internal wall surface, complete all as specified and directed. |
| 31 | M&L for 15mm thick rendering on fair faces to brick work or Block masonry surface in CM 1:4 finished the surface even and smooth (without using extra cement on internal wall surface, complete all as specified and directed. |
| 32 | Peparation of new plastered or unplastered surfaces of walls and applying two coats of Oil bond distemper, white or tinted, over 2mm coat wall putty complete all as specified and directed. |
| 33 | M & L for new plastered or unplastered surfaces of walls and applying two coat of acrylic weather proof paint (Exterior grade) over a coat of primer complete all as specified and directed.by Engr-in-Charge |
| 34 | Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified. |
| 35 | Preparation of new galvanised steel surfaces of any description not otherwie described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed. |
| 36 | Dismantling Prelaminated particle boarding, any description, fixed in any position with screws complete all as specified and directed. |
| 37 | S&F Solid PVC wall lining consisting of 5mm thick plain single colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications as specifed and directed. |
| 38 | Dismantling water tanks and S&F rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections including 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site complete all as specified and directed. |
| 39 | Dismantling water tanks and S&F rotational moulded polyethylene water storage tank 1000 litres capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections including 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site complete all as specified and directed. |
| 40 | S&F in repair for vitreous china squatting pan, 'orissa' pattern, size 580 x 440 mm white , with integral foot rests (excluding flushing cistern and flushing pipe), including connection to trap and to flushing pipe, anti-syphonage pipe, etc, complete including making good to floor complete all as specified and directed. |
| 41 | S&F in repair for 10 litre capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia. PVC flushing pipe, PVC connection 15 mm size with PTMT nuts of length 450 mm and with CP brass coupling & PVC washer at both ends,complete all as specified and directed. |
| 42 | S&F in repair for Vitreous china wash basin, white, flat back, size 550 X 400mm excluding taps, waste, chain and plug and pocelain stopper but incl brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete fixed in repairs complete all as specified and directed. |
| 43 | S&F in repair waste coupling 32mm CP for glazed ware sinks, basins etc with long screwed sha k or fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 44 | S & F in repair Stainless steel curtain rods 25mm dia fancy type with required supports, and open/end brackets complete all as specified and directed. |
| 45 | S&F in repair for Pillar tap for 15 mm bore, cast copper alloy, with capstan heads, chromium plated, screwd down high pressure, with or withou lettered 'hot' or 'cold' with long screwed shanks and fly-nuts, screwed for iron pipes complete all as specified and directed. |
| 46 | S&F in repair for bib cock CP for 15mm bore fancy type, cast copper alloy, screwed down, screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed. |
| 47 | S&F in repair for CP Stop cock / angle valve 15 mm cast copper alloy screwed down high pressure, screwed both ends for iron pipes or for unions, 15mm bore fancy type and fixed in repairs complete all as specified and directed. |
| 48 | S&F in repair for PVC connections 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed. |
| 49 | S&F in repair Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. complete all as specified and directed. |
| 50 | S&F in repair Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 25 mm bore pipe, screwed for iron pipe and fixed complete all as specified and directed. |
| 51 | S&F in repair PVC (SWR) floor trap 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 52 | S&F in repair PVC (SWR) Nahani trap 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 53 | S&F for 600mmx450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 54 | S&F in repair for PVC bib cock for 15mm bore fancy type, screwed down, screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed. |
| 55 | S&F in repair for PVC Waste pipe for Dia 32 mm bore complete all as specified and directed. |
| 56 | S&F in repair for PVC Urinal pipe for Dia 40 mm bore complete all as specified and directed. |
| 57 | S&F (concealed / open) 16 mm outer dia CPVC pipes & fittings SDR 13.5 pipes & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl drilling to holes in walls and fixing clamps as required complete all as specified complete with fitting including taking down existing GI tubing 15mm bore complete all as specified and directed. |
| 58 | S&F (concealed / open)20 mm outer dia CPVC pipes & fittings SDR 13.5 pipes & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl drilling to holes in walls and fixing clamps as required complete all as specified complete with fitting including taking down existing GI tubing 15mm bore complete all as specified and directed. |
| 59 | S&F (concealed / open) 25mm outer dia CPVC pipes & fittings SDR 13.5 pipes & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl drilling to holes in walls and fixing clamps as required complete all as specified complete with fitting including taking down existing GI tubing 15mm bore complete all as specified and directed. |
| 60 | S&F (concealed / open) 40 mm outer dia CPVC pipes & fittings SDR 13.5 pipes & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl drilling to holes in walls and fixing clamps as required complete all as specified complete with fitting including taking down existing GI tubing 15mm bore complete all as specified and directed. |
| 61 | Dismantling plain or corrugated steel sheeting any gauge thickness including Nanital or similar pattern roof covering complete all as specified and directed. |
| 62 | S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 63 | S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 64 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 65 | M&L for false ceiling work of galvenised MS ceiling grid system 'UNLOCK\\" comprising of main runner 38mmx24mmx0.35mm cross tee 38mmx24mmx0.25mm and GI suspenders 4mm dia fixed to ceiling with and including supply and fixing water proof laminated gypsum ceiling board of size 600x600x8 mm thick complete all as specified and directed. |
| 66 | Supply and Fix in repairs, seamless ceiling with using 12mm thick, factory made gypsum fiber board, fixed on GI frame work for seamless ceiling suitable for suspended system with and including applying two coats of oil bound distemper over a coat of primer to give even and smooth finish without showing any joints complete all as specified and directed. |
| 67 | S & F powder coated anodised Aluminium alloy sections sliding windows with frames 92 X29.6 X1.10mm , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.45mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. Note : Making all edges i.e. cill and jamb good by cement mortar 1:3 |
| 68 | S&F powder coated aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed. |
| 69 | S & F for anodised Aluminium partition/ door frame of size 100 x44 x 1.98mm thick with one or more rebates and shutters pull and push type or side hung type (with or without aluminium sash bars) comprising of top & lock rails of section 115 x 44 x 1.98mm thick, bottom rail of section 150 x 44 x 1.98mm thick and stiles of section 85 x 44 x1.98mm thick including necessary jointing cleat, glazing clip, rubber packing anodized aluminium beading, screws, anodized aluminium fittings such as floor spring or hinges 100mm size with hydrolic door closer, handles 'D' type 125mm, floor door stopper, tower bolts 200mm, sliding door bolt 300mm or mortice lock with 5mm thick tinted glass /pre laminted particle board (Novapan) panel and making good to the disturbed wall surfaces to match existing surface complete all as specified and directed. |
| 70 | M & L powder coatedaluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 37x19x2mmcomplete all as specified and directed. |
| 71 | S&F in repair brass 4 Levers Mortice lock, vertical type size 100 mm, complete all as specified and directed. |
| 72 | M&L in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed. |
| 73 | S&F in repair aluminium door coser hydraulically regulated, designation No. 3 universal type suitable for door shutter of 851 to 1000 mm in width complete all as specified and directed. |
| 74 | S&F in repairs tubular towel rail brass chromium plated, 20mm dia, D type 60 cm long between flanges complete all as specified and directed. |
| 75 | S&F in repair brass chromium plated shower rose 125mm size, with or without swivel joints, including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour, fixing to steel pipe or union complete all as specified and directed. |
| 76 | Disconnecting existing tanks, 250/ 500/1000 litres capacity, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position and making connections with existing water supply line, complete all as specified and directed. |
| 77 | M & L for water proofing treatment to roof slab by applying one coat of bituminous / polymrised primer confirming to IS 3384 @ 0.30 ltr /sqm and laying grit finish Actetic Polypropylene (APP) modified membrane pre-fabricated , reinforced with non woven polyester , of 3.50 kg/sqm (minimum) , 3mm thick minimum with minimum 75mm side overlaps and minimum 100mm end overlaps etc all as specified. ( NOTE ;- Taking down also include in this rate) |
| 78 | M&L Rendering 10 mm thick in CM(1:3) rendering on roof surfaces complete as all specified and directed. |
| 79 | M & L for PCC(1:2:4) as in levelling course on roof surfaces complete all as specified and directed. |
| 80 | Dismantilng wrought iron or mild steel work of any description not otherwise provided for all as specifed and directed. |
| 81 | M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1998 grde St-240 complete all as specified and directed. |
| 82 | M&L for framed brackets of angles or tees with web and franges cut to shape, drilled and countersunk for screw incl bending and welding angles, as necessary gusset plate plates, reviting etc 10 kg each brackets confirming to Fe 290 Gde E-165 complete all as specified and directed. |
| 83 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided as in RCC Jalies , louvers etc and similar suspended work and removing from site as approved and directed. |
| 84 | M&L for 35mm thick Pre Cast Cement concrete louvers and jallies 1:2:4 type B0 using 12.5 mm graded stone aggregate (measured solid) including all mounding but excluding frame and set in CM 1:4 as approved and directed. |
| 85 | Dismantling of PVC drain pipes of internal dia 100mm jointed in cement mortar and taking out of treanches/fixed to wall complete all as specifed and directed. |
| 86 | Dismantling of PVC drain pipes of internal dia 75 mm jointed in cement mortar and taking out of treanches/fixed to wall complete all as specifed and directed. |
| 87 | S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall ceiling, floor etc 110mm bore of pipe (fixed in repair) complete all as specfied and directed. |
| 88 | S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall ceiling, floor etc 75 mm bore of pipe (fixed in repair) complete all as specfied and directed. |
| 89 | S&F PVC (SWR) bends of any radius for 110 mm bore pipe (fixed in repair) complete all as specifed and directed. |
| 90 | S&F PVC (SWR) bends of any radius for 75 mm bore pipe (fixed in repair) complete all as specifed and directed. |
| 91 | S&F PVC (SWR) branch pieces(single Y) equal or unequal of 110 mm bore and fixed complete all as specifed and directed. |
| 92 | S&F PVC (SWR) branch pieces(single Y) equal or unequal of 75 mm bore and fixed complete all as specifed and directed. |
| 93 | S&F PVC (SWR) branch pieces(Double Y) equal or unequal of 110 mm bore and fixed complete all as specifed and directed. |
| 94 | S&F PVC (SWR) branch pieces(Double Y) equal or unequal of 75 mm bore and fixed complete all as specifed and directed. |
| 95 | S&F PVC (SWR) junction single (single T) equal or unequal of 110 mm bore pipe and fixed complete all specifed and directed. |
| 96 | S&F PVC (SWR) junction single (single T) equal or unequal of 75 mm bore pipe and fixed complete all specifed and directed. |
| 97 | S&F PVC (SWR) junction single (double T) equal or unequal of 110 mm bore pipe and fixed complete all specifed and directed. |
| 98 | S&F PVC (SWR) junction single (double T) equal or unequal of 75 mm bore pipe and fixed complete all specifed and directed. |
| 99 | Taking down and refixing the same aluminium door shutter after resecuring/ readjusted to aluminium section weighing not less than 0.55 kg/m including necssary joining cleats,glazing clips,ruber neoprene packing, handle 2 Nos in Each door, hinges, anodised aluminium snap bidding, screw etc. and renew unserviceable items such as fittings, sections, glass, Solid PVC sheets etc complete all as specified and directed. |
| 100 | M&L for 18-20 mm thick granite (Jet Black) work (table rubbed and polished and moulding of outer edges) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 101 | M&L for welding in repairs n.exc. 2.5 cm in length and n.exc. 6mm thick, complete all as specified and directed. |
| 102 | M&L for preparation of old decorated surface and applying one coat of white wash on walls , complete all as specified and directed. |
| 103 | M&L for preparation of old decorated surface of ceiling and applying one coat of white wash on Ceiling complete all as specified and directed. |
| 104 | M & L for preparation of old decorated surface and applying one coat of distemper oil emulsion complete all as specified and directed. |
| 105 | M & L existing treatment on walls and applying two coat of distemper oil emulsion over a coat of primer complete all as specified and directed. |
| 106 | M& L for preparation of old decorative surface of wall and applying one coat of acrylic weather proof paint (Exterior grade) Complete as all specified and directed. |
| 107 | M & L for existing treatment on walls and applying two coat of acrylic weather proof paint (Exterior grade) over a coat of primer complete all as specified and directed. |
| 108 | M& L of Preparation of old decorated surfaces and applying one coat of Terracota Paint on Floor and Wall Surfaces complete as all specified and directed. |
| 109 | M& L for applying Cement putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete as all specified and directed. |
| 110 | M & L for tank cleaning of pvc or rcc (1000 ltr) overhead water tank and mentioning date of cleaning by paint or marker etc ,all as specified and directed. Note:- It include material required like cloth ,chemical ,water to rinse etc |
| 111 | M & L for tank cleaning of pvc or rcc (500 ltr) overhead water tank and mentioning date of cleaning by paint or marker etc ,all as specified and directed. Note:- It include material required like cloth ,chemical ,water to rinse etc |
| 112 | S&F Single Piece WC with PP Close Seat cover Hinges Dual Flush Cistern Fitting Fixing Accessories And Accessories se S Trap 110mmas approved and directed. |
| 113 | S&F Brass chromium plated mixture for mixing hot and cold water, screwed down for iron pipe for 15mm dia bore pipe, fixed in repair, complete all as specified and directed. |
| 114 | S&F in Repair sinks made of stainless steel 1 m thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 115 | S&F PVC health foucet with 1500 mm long flexible mild steel tube with wall hook complete all as specified and as directed. |
| 116 | Taking down top assembly complete (except curtain & side bracket) of rolling shutter area not exceeding 10 square meter each, push pull or manual type and re-fixing the same in same position after necessary repairs such as cleaning, oiling, greasing, cleaning of the side guided channels, replacement of rusted nuts and bolts, including replacement of rusted profiles and welding / grinding as required for proper and smooth function complete all as specified and as directed.Note: (i) Unserviceable spare part such as suspension shaft, spring, ball bearing etc if found unserviceable will be replace with new one and the same will be measurable & paid separately as supply only under respective items of this Sch(ii) Gear box assembly if found unserviceable will be replace with new one and the same will be measurable & paid separately as supply & fix in repair under respective items of this schedule. |
| 117 | All as per item No 1 above including notes but area exceeding 10 Square meter but not exceeding 20 Sqm each complete all as specified and directed. |
| 118 | Supply only steel ball bearing suitable for rolling shutter complete all as specified and directed.Make: SKF, NBC, TATA or equivalent |
| 119 | Supply only 40 mm bore G.I Pipe medium grade as in suspension shaft for rolling shutter, cut to size including necessary drilling / grinding etc complete all as specified and directed. |
| 120 | Supply only 50 mm bore G.I Pipe medium grade as in suspension shaft for rolling shutter, cut to size including necessary drilling / grinding etc complete all as specified and directed. |
| 121 | Supply only helical type steel spring suitable for rolling shutter of size exc 5 Sqm but n.exc 10 Sqm complete all as specified and directed. |
| 122 | Supply only helical type steel spring suitable for rolling shutter of size exc 10 Sqm but n.exc 20 Sqm complete all as specified and directed. |
| 123 | S&F in repair mild steel Safety lever locks sutaible for rolling shutters complete all as specified and directed. |
| 124 | Taking down guide channel of any size and supply & fix guide channel of size 75 mm deep fabricated with 3.15 mm thick plain black sheet for rolling shutter including necessary welding including painting of guide channel with 2 coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed. |
| 125 | Supply and fix Gear box assembly for rolling shutter including rod, required nuts, bolts, cleats, crank handle etc, complete of standard make and fixed in position including one shop coat of primer including removal of old gear box assembly and other accessories complete all as specified as directed. |
| 126 | S&F in repair Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets Complete all as specified and as directed. |
| 127 | S&F in repairs Steel rolling shutters made of 1.00 mm thick lath,with ball bearing,as specified including top cover,anchoring rod, hasp and staple, errected in position as indicated,complete gear operated type with bevel gear box and crank handle complete all as specified and directed. Note : - Ball bearing will be measured and paid seperately. |
| 128 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 129 | S&F rolled mild steel Fe 410-W (Gde-E-250) quality-B in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 130 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 131 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed. |
| 132 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed. |
| 133 | M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer on walls including a coat of cement based wall care putty complete all as specified and directed. |
| 134 | M&L for preparation of plastered wall surface including pilaster/cornices etc and applying two coats of acrylic emulsion (exterior weather coat) paint of any tint as approved over one coat of primer complete all as specified and directed. |
| 135 | M&L for preparation of old decorated steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 136 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified and directed. |
| 137 | S&F Conversion of Existing Gear Operated Rolling Shutters to Motorised Rolling Shutters Elero Rolltormotor Heavy-Duty side Driver Motor engineered for Automated Rolling Shutter Applications, featuring precision German manufacturing with high torque output, integrated thermal overload protection, low noise gear assembly and compatibility with control systems. Includes mounting hardware, limit switch calibration, control panel,reduction gear starter Approximate Size of Rolling shutter 6.30 x 8.00 Mtr complete all as specified as directed. |
| 138 | NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor. Please Enable Macros to View BoQ information |
