|
| 1 | ALAKKODE ANGANWADI |
| 2 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 3 | 10.25.2:Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 4 | 13.98.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work |
| 5 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 6 | THEKKUPURAM ANGANWADI |
| 7 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 8 | OD516713/2025-2026:Laterate masonry with neatly dressed laterate stone of size 30x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc. |
| 9 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 10 | 10.25.2:Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 11 | KIZHAKKEKARA ANGANWADI |
| 12 | OD526198/2025-2026:Laterate masonry with neatly dressed laterate stone of size 30x20x20cm or nearestsize in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc |
| 13 | 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 14 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 15 | 50.12.2.2:Providing & fixing Poly carbonate multi wall plain sheet 4 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal / vertical / curved surfaces, but excluding the cost of purlins, rafters, trusses and including cutting to size and shapes where ever required. |
| 16 | CHERKKAPARA ANGANVADI |
| 17 | 15.13.1:Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 50 metres lead:Of area 3 sq. metres and below |
| 18 | 50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood |
| 19 | 50.9.3.1:Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood |
| 20 | 50.9.4.1:Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood |
| 21 | 14.85:Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 22 | 10.2:Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 23 | OD525793/2025-2026:Supplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaint |
| 24 | 13.88:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 25 | 13.98.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work |
| 26 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 27 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 28 | 9.48.1:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding |
| 29 | KOOTTAPUNNA ANGANWADI |
| 30 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 31 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 32 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 33 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 34 | OD530513/2025-2026:Providing and fixing 150 mm UPVC Square gutter pipe over GI clamp of same profile @1 mtr C/C |
| 35 | 50.9.6.1:Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Using Anjili wood / jack wood 30 mm thick shutters |
| 36 | 13.88:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 37 | 13.98.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work |
| 38 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 39 | BANGAD ANGANWADI |
| 40 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 41 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 42 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 43 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 44 | 9.48.2:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc |
| 45 | OD530347/2025-2026:Supplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaintSupplying cutting in size fixing in position by welding etc for 2.5 mm dia 1.25 cm c/c ornearest size GI plane bar mash including all cost of priming and painting two coat withsynthetic enamalpaint |
| 46 | PODIPPALLAM ANGANVADI |
| 47 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 48 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 49 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 50 | 12.51.1:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm) |
| 51 | KARUVAKKOD ANGANVADI |
| 52 | OD525310/2025-2026:Demolishing Stone work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 53 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 54 | OD525318/2025-2026:Laterate masonry with neatly dressed departmental laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc. |
| 55 | OD525794/2025-2026:Laterate masonry with neatly dressed laterate stone of size 30x20x20cm or nearestsize in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc |
| 56 | 5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 57 | 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 58 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 59 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 60 | 13.46.1:Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 61 | MOUVAL ANGANVADI |
| 62 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 63 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 64 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 65 | 12.51.1:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm) |
| 66 | OD530526/2025-2026:Providing and fixing 150 mm UPVC Square gutter pipe over GI clamp of same profile @1 mtr C/C Please Enable Macros to View BoQ information |
