|
| 1 | Clearing light jungle and removing the debris etc., complete and as directed by the departmental officers. |
| 2 | Dismantling Brick masonry in Cement mortar walls under 3m high including removing the debris etc., complete and as directed by the departmental officers. |
| 3 | Removing the Aluminium partition 1/3rd fixed glazing 2/3rd prelaminated board including labour charge etc., complete and as directed by the departmental officers. |
| 4 | Dismantling the Doors & windows including removal of frames, hinges and fastenings etc., complete and as directed by the departmental officers.. |
| 5 | Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. B20 and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. |
| 6 | Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers - mixing by manual means. |
| 7 | Hire charges for providing barricading arrangements for 14 days use, using casuarina props of dia 8cm to 10cm as vertical posts with 0.60m embedded below ground level and 1.20m above ground level, fixing 5 to 8cm dia casuarina poles horizontally in 3 tires and the lowest should be 45 cm above ground level and tightly tied with vertical poles using new coir ropes provided in all places and removing the same after the counting is over including the cost of errection and conveyance of all materials to work site etc., complete complying with standard specification and as directed by the departmental officers. |
| 8 | Hire charges for providing and fixing 6mm thick plywood sheet including labour charges, cost of nails and fixing in position etc., complete complying with standard specification and as directed by the departmental officers and removing the same after the counting is over. (Hire Charges for 14 days only). |
| 9 | Hire charges for supplying and fixing casuarina poles of 10 to 13cm dia including labour charges, cost of materials, fixing in position etc., complete and removing the same after the counting is over and as directed by the departmental officers. (Hire Charges for 14 days only). |
| 10 | Hire charges for supplying and fixing 40mm thick Countrywood planks including labour charge for fixing in position etc., complete and removing the same after the counting is over and as directed by the departmental officers. (Hire Charges for 14 days only). |
| 11 | Providing fixing with G.C.I Sheet of required thickness including labour charges, cost of nails and removing the same on the same day after the counting etc., complete (Hire charges for 14 days only) and as directed by the departmental officers. |
| 12 | Supplying and fixing of new country wood reeper of size 2\\" x 1\\" at site of work etc., complete as directed by the departmental officers. (Hire Charges for 14 days only) and removing the same on the same day after counting is over. |
| 13 | Hire charges for Supplying and fixing weld mesh (10 Gauge) of size 7.5cmx2.5cm with silver oak scantling of required length and size for vertical, hotizantal and cross supports using country wood reepers of size 2\\"x1\\" including cost of materials and labour charges for fixing in position with all necessary accessaries etc., complete complying with standard specification and as directed by the departmental officers. (Hire Charges for 14 days only). |
| 14 | Hire charges for fixing frisking cabin stand of required size using casuarina poles of 5cm to 8cm dia for vertical post horizontal post including cost of materials, labour charges etc., complete and removing the same after the counting is over and as directed by the departmental officers. (Hire Charges for 3 days only). |
| 15 | Renewing the damaged glass panes with new 4mm thick plain glass panes including country wood beading with labour charges for fixing in position etc., complete complying with standard specification and as directed by the departmental officers. |
| 16 | Providing movable traffic stand of size 3.00mx1.00m using casuarina poles of 8cm to 10cm dia for vertical post and horizontal post of 5cm to 8cm dia porps cross bracings tied with necessary coir and nails etc., complete including cost of materials, labour charges for fixing in position etc., and removing the same after the counting is over and as directed by the departmental officers. (Hire Charges for 3 days only). |
| 17 | Brick work in Cement Mortar 1:5 (One Cement and Five CS Sand) using best quality Fly Ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for the following including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge. |
| 18 | For Superstructure in Ground Floor |
| 19 | Supplying and fixing of MS Grill / MS sections for check post including cost of bending, welding etc., complete complying with standard specification and as directed by the departmnetal officers. (hire charge for 14 days only) |
| 20 | Supplying and fixing 50mm dia G.I. Pipes of approved quality and best variety of 'B' class pipe for check post (hire charge for 14 days only) etc., complete and as directed by the departmnetal officers. |
| 21 | Labour charges for refixing windows and ventilators along with frames in position etc., complete and as directed by the departmnetal officers. |
| 22 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/ m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column, masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use. |
| 23 | Supplying and fixing 12mm thick wooden checquered plate including labour , conveyance, loading and unloading etc., complete. (Hire Charges for 14 days only). |
| 24 | Removing and refixing of Instrument Table (8 Nos) and Counter Table (20m length) etc., complete complying with standard specification. |
| 25 | Removing and refixing of Counter top of size 7.50 x 1.00m including replacing the damaged wooden runner, mica sheet etc., complete complying with standard specification. |
| 26 | Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm \\"P\\" or \\"S\\" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings. such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Enginer before use on works) White glazed European Water Closet with 10 liters capacity PVC flusing tank fixed on to wall. |
| 27 | Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).White glazed earthernware wash hand basin without pedestal. |
| 28 | Refixing in position with available wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, excluding cost for 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. |
| 29 | Supplying and fixing of AC Exhaust Fan 225mm (9\\") Sweep (Light Duty) complete complying with standard specifications. |
| 30 | Supplying and fixing of MS / Fibre Louvers Shutters arrangements for 225mm AC Exhaust Fan complete complying with standard specifications. |
| 31 | Supplying of 25 liters capacity bucket with mug etc., complete and as directed by the departmental officers. |
| 32 | Supplying, laying and jointing G.I. Pipes of approved quality and best variety of “B” class pipe of the following dia including labour fixing G.I. Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessary brick work / concrete and plastering wherever necessary with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all floors complying with standard specification. G.I. pipes shall be got approved by the Executive Engineer before use on works.Internal water supply - Above Ground Level. |
| 33 | 20mm GI pipe |
| 34 | Supplying and fixing in position the following GI Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The GI specials should be got approved by the Executive Engineer concerned before use on works.) |
| 35 | GI Elbow 20mm dia |
| 36 | GI Tee 20mm dia |
| 37 | GI Reducer 20 x 15 mm dia |
| 38 | Supplying and fixing solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.Solid panel PVC door with frame. |
| 39 | Supplying and fixing in position 15mm dia SS tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) |
| 40 | Supplying and fixing in position screw down Tap 15mm Dia (Heavy Type) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) |
| 41 | Supplying and fixing position CI Nahani Trap / Floor Trap of size 100 x 75mm with stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Crushed stone sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) |
| 42 | Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 500 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) |
| 43 | Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The towel rail should be got approved by Executive Engineer before use on works). |
| 44 | Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works). |
| 45 | Supplying and fixing in position CPTwo Way Bib Cock with Health Faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Health Faucet should be got approved by the Executive Engineer before use on the works) |
| 46 | Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level |
| 47 | 110mm PVC pipe |
| 48 | Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 49 | 110mm PVC bend |
| 50 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI / 1mm 125 GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. |
| 51 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI / 1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi powder point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixedto the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. |
| 52 | Supplying and fixing of 25mm dia Curtain rod including cost of clamps, end caps, labour charges for fixing etc complete. (Hire Charges for 14 days only). |
| 53 | Supplying and fixing the Curtain cloth including with all accessories and fixing in position etc., complete. (Hire Charges for 14 days only). |
| 54 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 55 | Providing and fixing the platform of size 4.90mx2.40mx0.45m using necessary country wood scantling and country wood planks of 40mm thick including labour charge for fixing in position etc., and cost of nails etc., complete. (Hire charges 14 days only) and removing the same after counting is over and as directed by the departmental officers. |
| 56 | Hire charges for providing and removing arbian tent (Pagoda Tent) white colour of good variety in condition including cost of transpotation to site or venue fixing in position with necessary stray arrangements etc., (Hire Charges for 2 days only). |
| 57 | Supplying and laying with new best colour and quality of non woven carpet (Red Carpet) including finishing etc., complete. (Hire Charges for 10 days only). |
| 58 | Hire charges for single seat and double seat sofa including conveyance, Loading, Unloading charges etc., complete. (Hire Charges for 10 days only). |
| 59 | Hire charges for supplying and fixing of officer roller chair having push back arrangement and height adjustement hydraulic lever arrangement . The chair should be made of cold rolled mild steel tuffened sections for frame arrangements, the rester and the seater is to be finished with 35mm density foam and the top of the foam arrangement is to be finished with rexin cloth of approved design. The seater is to be supported on single stem with verical adjustable lever arrangements and supported on four legged roller arangements. The rollers are to be made with heavy duty thermo plast rollers with necessary screw arrangements etc., complete complying with standard specifications. (Hire Charges for 10 days only). |
| 60 | Supplying and fixing following furniture fittings including fixing position etc., complete complying with standard specifications and as directed by departmental officers. |
| 61 | Aluminium Hinges 125 x 30 mm |
| 62 | Aluminium Tower bolt 200mm long and 12mm dia |
| 63 | Aluminium Aldrop 200mm long and 12mm dia |
| 64 | Aluminium Handle 150 mm |
| 65 | Aluminium Padlock |
| 66 | White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed. |
| 67 | Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works. |
| 68 | Labour charges for shifting of furniture, Resetting of Furniture etc., complete (Mazdoor Category I). |
| 69 | Labour charges for attending emergency works in counting center etc., complete ( Mazdoor Category II) |
| 70 | Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct-ed by the departmental officers. |
| 71 | Supplying and fixing of protective sheet of required thichness in roof etc., complete complying with standard specification (Hire charges for 10 days only) |
| 72 | GST @ 18% Please Enable Macros to View BoQ information |
