|
| 1 | Sub work No- CONSTRUCTION OF R.Q. SHADE (PART-A) Item No. 1- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Bd.A.1 Page Number 259 |
| 2 | Item No. 2- Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means Bd.A.2 Page Number 259 |
| 3 | Item No. 3- Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete. |
| 4 | Item No. 4- Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Bd.A. 12 Page No. 264 |
| 5 | Item No. 5- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate |
| 6 | Item No. 6- Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in plinth as backing in composite masonry including bailing out water manually, striking joints, raking out joints and watering etc Complete. |
| 7 | Item No. 7- Providing and laying Cast in situ/Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 8 | Item No. 8- Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:4 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete. |
| 9 | Item No. 9- Providing and fixing of colour coated Zincaluminium( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated withAluminium-Zinc alloy (55% aluminiumm 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyster paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 mm, comprising of nominal 25mmexterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with sublet square fluting in the five pan at nominal 180-250 mmcenter- to-center. The end rib shall be designed for anti-capacity groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52Kilogram/Square Metre) |
| 10 | Item No. 10- Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 11 | Item No. 11- Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (Without mechanical gear) |
| 12 | Item No. 12- Providing and laying Rough Shahabad Stone Flooring 25mm to 30mm thick and of required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete. |
| 13 | Item No. 13- Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. |
| 14 | Item No. 14- Charges of Testing of material in vigilance and quality control laboratory for concrete compressive strength of C.C. cubes |
| 15 | Item No. 15- GST |
| 16 | Sub Work No. -2 INSTALLATION OF R.O. UNIT (PART-B)Item No. 1 - Providing and errecting HDPE rotational moulded Raw Water Storage Tank of 2000 Liter Capacity |
| 17 | Item No. 2- Raw water pump 1.0m3/hr single |
| 18 | Item No. 3- Raw & PWT Level Switch |
| 19 | Item No. 4- RWP Suction and Discharge Ball Value |
| 20 | Item No. 5- RWP Discharge Pressure Guage Black |
| 21 | Item No. 6- DMF 13 X 54 FRP Vessel |
| 22 | Item No. 7- Media Sand + Support Bed 13 x 54 |
| 23 | Item No. 8- ACF, 13 x 54 FRP Vessel |
| 24 | Item No 9- Media –Support Bed+Carbon 13 x 54 |
| 25 | Item No 10- 25 NB Manual MPV and Internals for the above vessel |
| 26 | Item No 11- Antiscalant Dosing Pump, 0-6 lph |
| 27 | Item No 12- 30 Ltrs Dosing Tank ( HDPE) |
| 28 | Item No 13-Antiscalank chemical |
| 29 | Item No 14- Cartridge filter 1.5 m3 / hr 20 ' Housing PP |
| 30 | Item No 15- CF, 20\\" with PP spun cartridge (Jambo) |
| 31 | Item No 16- High Pressure Pump,1.5m3 /hr Single Phase 2 HP |
| 32 | Item No 17-HPP Dischage Ball Valve |
| 33 | Item No 18-Pressure Vessel Suitable For 1 Nos 4 Memrance in SS304 |
| 34 | Item No 19-4x40 Membrance |
| 35 | Item No 20-Low and High Pressure Switch |
| 36 | Item No 21- Rotameter, RO Permeate , Reject Water etc.t |
| 37 | Item No 22- Permeate Storage Tank, of 1000 litre capacity S.S |
| 38 | Item No 23- Skid 202 SS |
| 39 | Item No 24- Control Panel, 1-1 |
| 40 | Item No 25- PH Booster Dosing Pump, 0-6 lph |
| 41 | Item No 26- 30 Ltrs Dosing Tank (HDPE) |
| 42 | Item No 27- PH Boost Chemical |
| 43 | Item No 28- 1000 LPH UV |
| 44 | Item No 29- HPP Pressure Gauge |
| 45 | Item no 30- Rej flushing Solenoid Valve |
| 46 | Item no 31- UPVC & Fittings |
| 47 | Item no 32- Hardware , Accessories ,Wiring & Cable Accessories |
| 48 | Item no 33- Installation Errection and Commissioning job work |
| 49 | Item no 34- Water ATM Smart card Base |
| 50 | Item No 35- Water Chiller Spilit type on Line 2 Tonne |
| 51 | Sub WorkNo-3 Electrification Work (PART-C)Item No 1-Supplying & laying HMS PVC conduit 20mm diawith necessary accessories in RCC work/ false cellingfalse flooring as per specification No. |
| 52 | Item No 2-Supplying&erecting mains with 2x1.5sq mm FR copper PVC insulated wire laid in provided conduit/truking/inside pole/Bus bars or any other places as per specification No; WG MA/BW |
| 53 | Item No 3-upplying &irecting mains with 2x1.5 sq mm FR copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places. as per specification No.WG-MA/BW |
| 54 | Item No 4-Supplying &erecting mains with 2*3.5 sq mmFR copper PVC insulated wire laid in provided conduit/truking/inside pole/Bus bars and any other palaces as per specification No WG-MA/BWng watering complete Spec No.Bd H.1page No.329 |
| 55 | Item No 5-Supplying &erecting mains with 1*2.50sq mm FR coppper PVC insulated wire laid in provided conduit/trunking/incide pole/Bus Bar and any other places as per spacification No WG-MA/BW |
| 56 | Item No 6-Supplimg any erecting mains with ISI mark WP 2*4 sq mm.1100 V grade aluminiam PVC insulated and PVC silhed wires on GI bearer wire No 8 SWG complate erected with required size of porcelaim reel insulators and 16 SWG GI binding wire |
| 57 | Item No 7-Supplying and erecting ISI mark modular type switch 6A/10A duly erected on provided plate and box with wiring connections complete. |
| 58 | Item No 8- Supplying and erecting ISI mark modular yupe3 pin 6A multy sockets with safety sutter duty erected on provided plate and box with wring connections complete. |
| 59 | Item No 9-Suppling and erecting PVC surfacemodulart switch box with double mounting plate for 6 modules duly erected |
| 60 | Item No 10-Wiring for plug on board with switch socket copper wring and earthing as pert specification No WG-PW/SW |
| 61 | Item No 11- Supplying & erecting ready to use Retrofit T8 LED, 18 / 20 watt tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary as per specification No. FG-LP/RET |
| 62 | Item No 12- Supplying erecting &marking SPMCB 6A to 32A B-series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB |
| 63 | Item No 13-Suppyling erecting& marking DPMCB 6A to 32B-series (for lighting) in provided distrubition board as per specification no SW-SWR/MCB |
| 64 | Item No 14-Supplying erecting and marking enclosure ingle pole and natural distrubition board (SPNDB) one way for SPMCB 1 no on iron/ GI frame as per specification no SW-SWR/MCBDB |
| 65 | Item No 15-Supplying erecting CRCA sheet metal one way inclosures suitable for DP MCB/TP MCB/FT MCB erected on angle iron /GI frame complate |
| 66 | Item No 16-Providing pipe type earthing with 40mm dia GI pipe or20mm disa GI redcomplate with all materials as per specification no EA-EP |
| 67 | Item No 17-M S E D C L Electrucity Connetion Charge s |
| 68 | Item No 18-GST |
| 69 | Sub Work No 4- PIPE LINE ON OTHER WORK ( PART-D)Item No 1- Supplying and erecting high density polythene pipe ISI mark 32 mm dia. suitable for pressure of 6 kg/cm2 connected to jet/submersible pump with required material complete |
| 70 | Item No 2-Supplying and erecting 25 mm dia. Ball cock at position with necessary materials complete. |
| 71 | Item No 3- Supplying and erecting fully automatic line voltage stabilizer, buck and boost type for operation on input voltage 160 to 270 V and output voltage 200 to 250 V rated for,5 kVA maximum load and with voltmeter, selector switch, 6A/16A flush type 3 pin socket for output and with 3 core flexible cord and 3 pin 6/16 A plug top suitable for Air Conditioner of 2.00 TR |
| 72 | Item No 4- Scheme Information Painting like Name of Work, Estimated Amount,Name of Agency etc.as per office instruction |
| 73 | Item No 5- GST |
| 74 | Item No 5- Royalty Charges for Rubble stone, stone masonary, sand, metal, murum etc. complete |
| 75 | Item No 6- Water sample testing charges before and after R.O. Unit Installation etc complate |
| 76 | Item No 7- Charges of Testing of material in vigilance and quality control laboratory for Concrete Compressive Strength of C.C. Cube |
| 77 | Item No 8-Third Party inspection charges for R.O. Unit etc complate Please Enable Macros to View BoQ information |
