Tender For Vertical Extension Of Taluka Court Building At Georai Tq. Georai Dist. Beed (First Floor - 4 Court Hall), Beed-Maharashtra

TDR : 54902543

Tender Notice
BOQ

4 Days Left

Beed , Maharashtra

Tender Brief : Tender For Vertical Extension Of Taluka Court Building At Georai Tq. Georai Dist. Beed (First Floor - 4 Court Hall)

Document Fees
₹ 3540 /-

EMD
₹ 303500.0 /-

Tender Value
₹ 6.06 Crore /-

Submission Date
06-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Removing Galvanised Iron or Asbestos Cement sheet roofing including purlins, principal rafters etcetera including sorting serviceable and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etcetera complete.
2	B] First Floor
3	Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etcetera
4	B] First Floor
5	Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etcetera complete.
6	B] First Floor
7	Removing brick bat coba including stacking the spoils as directed with all leads, lifts etcetera complete.
8	B] First Floor
9	Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etcetera complete.
10	B] First Floor
11	Lowering down the debris obtained from breaking and removing the cement plaster / burnt brick masonry of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete.
12	B] First Floor
13	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete,(Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
14	A] Ground Floor
15	B] First Floor
16	Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
17	A] Ground Floor
18	B] First Floor
19	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for Reinforced Cement Concrete slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete,(Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
20	A] Ground Floor
21	B] First Floor
22	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/ pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
23	A] Ground Floor
24	B] First Floor
25	Providing and laying in situ / ready mix M-25 Reinforced Cement Concrete of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete work of Box Cell including scaffolding, compaction, formwork finishing and curing etcetera complete. (excluding reinforcement, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications (VSI sand finely washed etcetera )
26	A] Ground Floor
27	B] First Floor
28	Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for Reinforced Cement Concrete Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/ pumping, compaction, finishing uneven and honeycombed surface with Cement Mortor 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etcetera) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
29	A] Ground Floor
30	B] First Floor
31	Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etcetera complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etcetera (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)
32	B] First Floor
33	Providing and fixing in position Thermo Mechanical Treated (TMT) - FE - 500 bar reinforcement of various diameters for Reinforced Cement Concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etcetera as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.
34	A] Ground Floor
35	B] First Floor
36	Providing expansion joints in reinforced cement concrete framed structure (interior columns) with plain premoulded filler with Confirming to Indian Standard 1838,1961, 25 mili metre thick with 75 mili metre wide and 1 mili metre thick stainless steel plate finishing etcetera complete as directed
37	B] First Floor
38	Providing expansion joints in Reinforced Cement Concrete framed structure (exterior column) with plain premoulded filler 25 mili metre thick with 75 mili metre wide and 1 mili metre thick stainless steel plate and finishing etcetera complete.
39	B] First Floor
40	Providing expansion joints in Reinforced Cement Concrete framed structure (at floor level) with plain premoulded filler 25 mili metre thick with 75 mili metre wide and 1 mili metre thick stainless steel plat and finishing etcetera complete.
41	B] First Floor
42	Providing expansion joints in Reinforced Cement Concrete framed structure (at Terrace level) with premoulded filler 25 mili metre thick with 40 mili metre wide and 1 mili metre thick stainless steel plate as required, bitumen poured filler and finishing etcetera complete as directed.
43	B] First Floor
44	Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etcetera Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)
45	A] Ground Floor
46	B] First Floor
47	Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etcetera Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)
48	B] First Floor
49	Providing and fixing chicken mesh of 22 gauge, with about 30 centi metre width at the junction of Reinforced Cement Concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /Burnt Brick Masonry and or tying by binding wire etcetera complete.
50	B] First Floor
51	Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etcetera complete.
52	A] Ground Floor
53	B] First Floor
54	Providing internal cement plaster 20 mili metre thick in single coats in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etcetera complete
55	A] Ground Floor
56	B] First Floor
57	Providing internal cement plaster 12 mili metre thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etcetera complete.
58	B] First Floor
59	Providing and applying plaster / wall punning with plaster of paris ( with plaster of paris material of Ambuja / Mor Chap or equivalent make ) in 10 to 13 mili metre thickness to previously plastered surface / or on newly brick surface (Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etcetera complete.
60	A] Ground Floor
61	B] First Floor
62	Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mili metre thick in cement mortar 1:4 using waterproofing compound at 1 Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mili metre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etcetera complete.
63	A] Ground Floor
64	B] First Floor
65	Providing fine cement finish 1.5 mili metre thick over green plaster surface including scaffolding curing etcetera complete.
66	B] First Floor
67	Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 mili metre thickness on previously plastered surface, including Plaster Groove 6 mili metre thickness or Tape Grooves 35 to 45 mili metre thickness or as required, in all position including preparing the surface, scaffolding etcetera complete.
68	B] First Floor
69	Providing water proof bedding for flooring of Bath and Water Closet 25 mili metre thick in Cement Mortor 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etcetera complete.
70	B] First Floor
71	Providing waterproofing in Water Closet and bath including brick bat coba in all position including providing and laying 12 mili metre bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in centi metre 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20 mili metre thick brick bedding in centi metre mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etcetera complete.
72	B] First Floor
73	Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in Cement Mortor1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with Cement Mortor1:3 admixed with approved water proofing compound and finally top finishing with average 20 mili metre. thick layers of same mortar added with jute fiber at 1 Kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 mili metre x 300 mili metre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etcetera complete.
74	B] First Floor
75	Providing waterproof plaster in Water Closet and bath 12 mili metre thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram per bag of cement of approved make and manufacturer and curing etcetera complete. (Excluding Tiles) (As directed by Engineer in Charge)
76	B] First Floor
77	Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300 mili metre x 40 mili metre x 5 mili metre with oil painting, etcetera complete
78	B] First Floor
79	Providing and fixing M-40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to Indian Standard 6524-1983 having 6 mili metre diametre bars 3 Numbers And stirrups @250 mili metre centre to centre and fixing in wall with 6 Nos of hold fast of 12 mili metre diametre bars 500 mili metre long including primer and oil painting etcetera complete) frame size 60 mili metre x 100 mili metre
80	B] First Floor
81	Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mili metre thick for door frame/ dado/ window boxing etcetera On Cement Mortor 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etcetera complete.
82	B] First Floor
83	Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mili metre to 20 mili metre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in Cement Mortor 1:3 curing and cleaning etcetera complete.
84	B] First Floor
85	Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mili metre thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mili metre thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete
86	B] First Floor
87	Providing and fixing solid core flush door shutter in single leaf 32 mili metre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mili metre thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etcetera complete.
88	B] First Floor
89	Providing and Fixing 30 mili metre thick BOTH SIDE PRELAMINATED SOLID PANEL Polyvenyle Chloride DOOR SHUTTER consisting of frame made out of Mild Steel tubes of 19 guage thickness and, size 19 x 19 mili metre for styles and 15 x15 mili metre for the top and bottom rails, Mild Steel frame shall have a coat of metel primer of approved make and manufacture. Mild Steel frame shall be covered with heat mouled Polyvenyle Chloride 'C' channel made from 5 mili metre(+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30 mili metre thickness 70 mili metre width out of which 50 mili metre shall be flat and 20 mili metre shall be tapered in 45 angle on either side forming stiles ; and 5 mili metre thick ,95 mili metre wide Polyvenyle Chloride sheet out of which 75 mili metre shall be falt and 20 mili metre shall be tapered in 45 on the inner side to form top and bottom rail and 115 mili metre wide Polyvenyle Chloride sheet out of which 75 mili metre shall be falt and 20 mili metre shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mili metre(+/0.25) thick Polyvenyle Chloride strip of 20 mili metre width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mili metre(+/0.25) thick Polyvenyle Chloride sheet to be fitted inside the Mild Steel frame welded/ sealed to the styles and rails with 5 mili metre(+/0.25) x 30 mili metrePolyvenyle Chloride sheet beading on either side and joined together with solvent cement adhesive etcetera ,10 mili metre thickness (5 mili metre(+/0.25) x 2 nos ) 20 mili metre wide cross Polyvenyle Chloride sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos Mild Steelpowder coated but hinges of size 100 mili metre x 25 mili metre x 2 mili metre using 32 mili metre long steel screws drilled suitable to pass through both the walls of the Mild Steel tube. Other hardwares should be fixed with 19 x 6 mili metre size steel screws including fixture fasting. Complete as per direction of engineer in charge.
90	B] First Floor
91	Providing and fixing in position. (as per Indian Standard 1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mili metre at weight 0.547 Kilogram/Running Metre and window frame bottom track section 61.85 x 31.75 x 1.20 mili metre at weight 0.695 Kilogram/Running Metre Top and side track section 61.85 x 31.75 x 1.30 mili metre at weight 0.659 Kilogram/Running Metre The shutter should be of bearing bottom 40 x 18 x 1.25 mili metre at weight 0.417 Kilogram/Running Metre Inter locking section 40 x 18 x 1.10 mili metre at weight 0.469 Kilogram/Running Metre And handle section 40 x 18 x 1.25 mili metre at weight 0.417 Kilogram/Running Metre and top section 40 x 18 x 1.25 mili metre at weight 0.417 Kilogram/Running Metre As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mili metre thick plain glass with all required screws and nuts etcetera complete. With powder coating without box
92	B] First Floor
93	Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mili metre at weight 0.637 Kilogram/Running Metre with window frame bottom track section 92 x 31.75 x 1.30 mili metre at weight 1.070 Kilogram/Running metre Top and side track section 92 x 31.75 x 1.30 mili metre at weight 0.933 Kilogram/Running Metre The shutter should be of bearing bottom 40 x 18 x 1.25 mili metre at weight 0.417 Kilogram/Running Metre Inter locking section 40 x 18 x 1.10 mili metre at weight 0.469 Kilogram/Running Metre and handle and top section 40 x 18 x 1.25 mili metre at weight o.417 Kilogram/Running Metre As per detailed drawings and as directed by Engineer-in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mili metre thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etcetera complete. With powder coating without box
94	B] First Floor
95	Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mili metre x 1.22 mili metre box type, 5 mili metre thick sheet glass louvers, of approved quality etcetera complete.
96	B] First Floor
97	Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mili metre thick in cement mortar 1:4 using waterproofing compound at 1 Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mili metre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etcetera complete.
98	A] Ground Floor
99	B] First Floor
100	Providing and fixing Mild Steel grill door 24 Kilogram/Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etcetera
101	B] First Floor
102	Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mili metre diametre and vertical pipe of 38 mili metre diametre at 0.60 metre centre to centre or as required and horizontal pipes of 25 mili metre diametre in three rows, all pipes of 2 mili metre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mili metre diametre above newel post of 75 mili metre diametre etcetera complete (Prior approval of sample and brand by Executive Engineer is necessary before use)
103	A] Ground Floor
104	B] First Floor
105	Providing and fixing 40 mili metre diameter and 1.5 mili metre thick Stainless steel hand railing in Stainless Steel 304 Grade including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etcetera complete
106	B] First Floor
107	Providing and laying handcut polished Kotah Stone flooring 25 mili metre to 30 mili metre thick and 30 centi metre wide in plain/diamond pattern on a bed of 1:6 Cement Mortor including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etcetera complete.
108	B] First Floor
109	Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etcetera complete. For Flooring
110	B] First Floor
111	Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mili metre thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etcetera complete.
112	B] First Floor
113	Providing and fixing machine cut machine polished 18 mili metre to 20 mili metre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etcetera complete.
114	A] Ground Floor
115	B] First Floor
116	Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centi metre x 30 centi metre and Confirming to Indian Standard 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etcetera complete.
117	B] First Floor
118	Providing and laying ceramic tiles of having size 30 centi metre x 30 centi metre and confirming to corresponding Indian Standard for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etcetera complete.
119	B] First Floor
120	Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mili metre to 605 mili metre x 590 mili metre to 605 mili metre of 8 to 10 mili metre thickness and confirming to Indian Standard 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etcetera complete.
121	A] Ground Floor
122	B] First Floor
123	Providing and laying vitrified mirror / glossy finish tiles having size 590 mili metre to 605 mili metre x 590 mili metre to 605 mili metre of 8 to 10 mili metre thickness and confirming to Indian Standard 15622-2006 ( group Bla) of approved make, shade and pattern for dado & skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etcetera complete.
124	A] Ground Floor
125	B] First Floor
126	Providing and fixing in position Gypsum board false ceiling with 12.5 mili metre thick Gypsum boards, screwed/fixed to the under structure of suspended Galvanised Iron Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mili metre maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etcetera all complete.
127	B] First Floor
128	Providing and fixing Modular false ceiling of 600 x 600 mili metre center to center and 13 mili metre thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mili metre x 40 mili metre) weighing 0.39 Kilogram/ metre at 60 centi metre center center and fixed with ½” x ½” (15 x 15 mili metre) flanges weighing 0.19 Kilogram/ metre suspended on 6 mili metre diametre mild steel rod weighing 0.22 Kilogram/ metre, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mili metre x 40 mili metre) weighing 0.39 Kilogram/ metre etcetera (all alluminium sections shall be anodized) including all labour, material, lifts etcetera complete.
129	B] First Floor
130	Providing and fixing on walls/ ceiling/ floor 15 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.
131	B] First Floor
132	Providing and fixing on walls/ceiling/floor 20 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.
133	B] First Floor
134	Providing and fixing on walls/ ceiling/ floor 25 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.
135	B] First Floor
136	Providing and fixing on walls/ ceiling/ floor 32 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.
137	B] First Floor
138	Providing and fixing on walls /ceiling/ floor 40 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.
139	B] First Floor
140	Providing and fixing on walls/ ceiling/ floor 50 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete.
141	B] First Floor
142	Providing and fixing 15 mili metre diametre screw down bib/ stop tap of brass including necessary socket union nut complete.
143	B] First Floor
144	Providing and fixing 20 mili metre diametre screw down bib/ stop tap of brass including necessary socket union nut complete.
145	B] First Floor
146	Providing and fixing screw down for 20 mili metre diametre wheeled stop tap of brass including necessary sockets/union nut complete.
147	B] First Floor
148	Providing and fixing screw down for 25 mili metre diametre wheeled stop tap of brass including necessary sockets/union nut complete.
149	B] First Floor
150	Providing and fixing screw down for 32 mili metre diametre wheeled stop tap of brass including necessary sockets/union nut complete.
151	B] First Floor
152	Providing and fixing screw down for 40 mili metre diametre wheeled stop tap of brass including necessary sockets/union nut complete.
153	B] First Floor
154	Providing and fixing screw down for 50 mili metre diametre wheeled stop tap of brass including necessary sockets/ union nut complete.
155	B] First Floor
156	Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etcetera complete.
157	B] First Floor
158	Providing and fixing wall mixer with overhead shower,shower arm,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)
159	B] First Floor
160	Providing and fixing 25 mili metre diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangement and lock. [Without chamber].
161	B] First Floor
162	Providing and fixing 40 mili metre diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangements and lock. [Withoutchamber].
163	B] First Floor
164	Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etcetera complete.
165	B] First Floor
166	Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres
167	B] First Floor
168	Providing, laying and fixing ,jointing Eco- drain 200 mili metre SN 4 Nu- Drain Unplastisized Polyvenyle Chloride pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per Indian Standard 15328 with fittings such a bends, tees tees, coupler etcetera jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated materialetcetera complete.
169	B] First Floor
170	Providing and fixing 1st class white glazed earthenware Orissa Type Water Closet Pan 580 mili metre diametre including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mili metre thick, 10 liter Poly Venyle Chloride flushing cistern with all necessary pipe connection etcetera complete.
171	B] First Floor
172	Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 mili metre size of approved make including soil pipe, vent pipe up to outside face of wall ,100 mili metre diametre Galvanised Iron plug bend inlet pipe all fittings, cuttingand making good walls, floors etcetera complete.
173	B] First Floor
174	Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195 mili metre size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mili metre thick fixed on Black Kadappa Framework, etcetera Complete as directed by Engineer in charge.
175	B] First Floor
176	Providing and fixing 10 centi metre Cast Iron Nahani Trap including Cast Iron grating bend and piece of Cast Iron pipe upto the outside face of the wall complete.
177	B] First Floor
178	Providing and fixing Poly Venyle Chloride Rain water pipes of 110 mili metre outer diameter and having wall thickness of 2.2 to 2.7 mili metre confirming to Indian Standard 13592-1992 including proper rainwater receiving recess with Poly Venyle Chloride plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25 mili metre to 40 mili metre from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on Cement Concrete or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the Poly Venyle Chloride fittings and additional 2 piece socket clips shall be got approved from engineer in charge etcetera complete.
179	B] First Floor
180	Providing and fixing 100 mili metre diametre stabiliser pipe/ Poly Venyle Chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etcetera complete.
181	B] First Floor
182	Providing and fixing in position Unplastisized Polyvenyle Chloride ultra violet stabilized 110 mili metre outer diameter cowl dome confirming to Indian Standard-4985 including making joints with solvent cement etcetera complete
183	B] First Floor
184	Providing and applying one coat of seal cement primer of approved manufacture and shed including scaffolding preparing the surface by cleaning dirt and other foreign matters, scrapping if necessary including scaffolding etcetera complete.
185	A] Ground Floor
186	B] First Floor
187	Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding Indian Standard of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary, and watering the surface for two days etcetera complete.
188	A] Ground Floor
189	B] First Floor
190	Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etcetera complete.
191	A] Ground Floor
192	B] First Floor
193	Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etcetera complete.
194	A] Ground Floor
195	B] First Floor
196	Providing and fixing 45 centi metre wide mild steel ladder of 40 mili metre x 6 mili metre Mild Steel flat stringers and steps of 18 mili metre diametre mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60 centi metre x 30 centi metre x 30 centi metre and painting the ladder complete. (Anti Corossive Paint)
197	B] First Floor
198	Providing and fixing 450 mili metre x 550 mili metre size superior type Belgium mirror with 16 mili metre diametre nickel plated towel rod etcetera complete.
199	B] First Floor
200	Providing and fixing 90 centi metre x 60 centi metre Granite plate engraving 10 centi metre height letter, figures including painting the lefters/figures with approved colour and shade complete
201	B] First Floor
202	Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etcetera', having rectangular shape of 1.20 metre x 0.90 metre size made out 18 gauge (1.25 mili metre) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etcetera with approved colour shade paint complete, on Mild Steelangle of size 35 x 35 x 3 mili metre frame with properly cross braced Mild Steel angles of size 35 mili metrex35 mili metrex3 mili metre duly painted including Two Mild Steel angle iron posts of size 65 mili metre x 65 mili metre x 6 mili metre, 3.65 meter long painted with alternate black and white bands of 25 Centi Metre width including all fixtures etceteraand fixing the boards in 1:4:8 concrete block of size 60 Centi Metre x 60 Centi Metre x 75 Centi Metre including, excavation, refilling, transportation, and labour etcetera complete.
203	B] First Floor
204	Providing and fixing of imported clay tiles pn Mild Steel frame Work using Maditerranean plus roof tiles of Wienberger tile of colour Red Engobe or equivalent with necessary accessories required to fix tile including clips and screw (Prior permission of S.E. is to be obtained before inclusion)
205	B] First Floor
206	RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast Reinforced Cement Concrete rings, 300 mili metre thick side filling around outside of Reinforced Cement Concrete rings (annular space) with 40 mili metre size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75 mili metre clean washed gravels followed by 0.5m depth of 10-25 mili metre of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) media layer including covering with Reinforced Cement Concrete slab, manhole frame & cover, Polyvenyle Chloride rungs etcetera including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge
207	A] Ground Floor
208	RWH - Recharge PitProviding and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast Reinforced Cement Concrete rings with 6.5\\" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated Polyvenyle Chloride casing pipe wrapped around with netlon mesh including 300 mili metre thick sidefilling around outside of Reinforced Cement Concrete rings (annular space) with 40 mili metre size boulders including filling of recharge pit up to 0.5m depth with 25-75 mili metre clean washed gravels from bottom up followed by 0.5m depth of 10-25 mili metre of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) media layer including covering with Reinforced Cement Concrete slab, manhole frame & cover, Polyvenyle Chloride rungs, Polyvenyle Chloride end-caps, fittings etcetera including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing.The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.
209	A] Ground Floor
210	Boring/drilling bore well of 300 mili metre diametre for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machinery required for the job, all complete as per direction of Engineer in charge, upto 90m depth below ground level.
211	A] Ground Floor
212	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized Polyvenyle Chloride medium well-casing pipe of 150 mili metre dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etcetera all complete, for all depths, as per the direction of Engineer in charge.
213	A] Ground Floor
214	Providing and laying concrete pipes of Indian Standard NP. class of 300 mili metre diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.
215	A] Ground Floor
216	Providing and fixing C.P. sink cock with raised J\\" shaped swinging casted spout ofapproved make including necessary sockets/ union nut etcetera complete.\\"
217	B] First Floor
218	Providing and fixing machine cut mirror polished 18 mili metre to 20 mili metre thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etcetera complete . Both side polish
219	B] First Floor
220	Clearing grass and removal of rubbish up to a distance of 50 Metres outside the periphery of the area.
221	A] Ground Floor
222	Providing patti/ band 100 mili metre wide on plastered surface 12 mili metre to 15 mili metre thick in Cement Mortor 1:3 line and level including neat finishing scaffolding curing etcetera complete.
223	B] First Floor
224	Providing groove to required size at specified location as directed by Engineer, at junction of brick masonry wall and Reinforced Cement Concrete beams or Column, at junction of composite masonry, including scaffolding, finishing, curing etcetera complete.
225	B] First Floor
226	Providing and fixing White Glazed Earthenware full stall type Urinal with Polyvenyle Chloride flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mili metre diametre Polyvenyle Chloride flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall
227	B] First Floor
228	Providing and fixing in position extruded aluminium partitions having frame made out of extruded tubular section of size 65 mili metre x 40 mili metre with 12 mili metre thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 129231990, laminated on both sides, Novateak or equivalent with aluminium glazing clips of size 12 mili metre x 12 mili metre(conical) as per drawing etcetera complete.
229	B] First Floor
230	Door Closure: (For 2 Hr fire Rated EN-3 Door Closure)Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors of different size (e.g size -EN-3 for leaf width upto 900mm) CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.) fitted and fixed Complete as per direction & satisfaction of Engineer -in Charge including all taxes & incidental charges.
231	B] First Floor
232	Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 metre x 2.40 metre with aluminium door frame of powder coated section 101.60 x 44.75 mili metre, 3.18 mili metre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mili metre x 44.5 mili metre x 3.00 mili metre thick top rails 47.62 x 44.45 mili metre x 3.00 mili metre thick, vertical style 47.62 x 44.45 mili metre, 3.00 mili metre thick and for shutter plain glass panes 5 mili metre thick for top panels and 12 mili metre thick both side laminated phenol bonded particle board panels for bottom panels etcetera, Indian Standard Institute mark, with bijagiri having heavy duty concealed lock, necessary beading, glazing clips, Polyvenyle Chloride gaskets, 250 mili metre length tower bolts, 150 mili metre diametre pad handle, etcetera as per detailed design and drawing or as directed by engineer in charge including all materials, labours, and equipment etcetera complete
233	B] First Floor
234	Providing and fixing lioghtening conductor system comprising of erecting Air-Termination consisting of tubular copper rod of 25 mili metre diametre 1.2 mili metre thick with multiple points head 1.2 Metric Tonne. long ( Heavy Duty) welded or clamped to Galvanised Iron pipe pole B grade 50 mili metre diametre of requiired length with Mild Steel round bnase plate 25 centi metre diam and 10 mili metre thick at bottom embeded in cement concrete 1:3:6 dfoundation of size 45 centi metre diam x 45 centi metre Height and providing earthing with copper earth plate of size 60 x 60 x 0.3 centi metre with cadmium plated nut bolts to fix earthing strip burried in specially prepared earth pits 1.5 metre below ground level with 40 Kilogram charcoal and salt with altemate layers of charcoal and salt and Galvanised Iron pipe 40 mili metre diametre 2 meter length burried in earthe upto earthling plate remining portion above ground level for watering and refilling comcpete Note- Copper strip fropm lightening conductor is not considered in this item.
235	B] First Floor
236	Providing and fixing shutter to wall cupboard made from 19 mili metre thick Teak particle board with approved coloured laminated face 1.5 mili metre thick bonded with phenol formaldehyde synthetic resin B.W.P. grade including lipping beading iron oxidised fixtures and fastening and oil primer coat etcetera complete. (Excluding cupboard frame).
237	B] First Floor
238	Providing and fixing during laying in Reinforced Cement Concrete Slab rectangular 2 mili metre thick Mild Steel sheet fan hook box of size 180x100 mili metre with required depth with holes or notches as required, bottom and top sides of 1.6 mili metreS. sheet fixed with 3.5 mili metre diametre round headed screws together with 12 mili metre diametre Mild Steel bar bent to shape with hooked ends for fan hook and painting to exposed surface
239	B] First Floor
240	Supplying, Drilling/Cleaning hole and injecting chemical. Application to be designed separately for Rebars as Simply Supported, Moment or Splice Connection as per EC2/TR 023 or relevant tested and accepted rebar guidelines. The chemical should have ETA approval for seismic rebar as a minimum qualifying criterion. Drilling hole with double flute type drill bits or hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard HDE A22 battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer‘s recommendations. The adequate diameter and embedment of rebars to be decided as per PROFIS Rebar Software & the report to be submitted to the project manager/ design engineer for approval. Scanning before drilling to be done to avoid hitting existing rebars. Re 500 -12 mm dia 240mm depth
241	B] First Floor
242	Supplying, Drilling/Cleaning hole and injecting chemical. Application to be designed separately for Rebars as Simply Supported, Moment or Splice Connection as per EC2/TR 023 or relevant tested and accepted rebar guidelines. The chemical should have ETA approval for seismic rebar as a minimum qualifying criterion. Drilling hole with double flute type drill bits or hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard HDE A22 battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer‘s recommendations. The adequate diameter and embedment of rebars to be decided as per PROFIS Rebar Software & the report to be submitted to the project manager/ design engineer for approval. Scanning before drilling to be done to avoid hitting existing rebars. Re 500 -16 mm dia 320mm depth
243	B] First Floor
244	Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etcetera complete. (Lift upto 1.5 metre) By Mechanical Means
245	A] Ground Floor
246	Excavation for foundation in hard murum including removing the excavated material upto distance of 50 Metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etcetera complete. (Lift upto 1.50 metre) By Mechanical Means
247	A] Ground Floor
248	Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.
249	A] Ground Floor
250	Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on bond paper.
251	A] Ground Floor
252	Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.
253	A] Ground Floor
254	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concrete columns and steel stanchions etcetera including bailing out water, Steel centering, formwork ,cover blocks, laying/ pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etcetera complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
255	A] Ground Floor
256	Providing soling using 80 mili metre size trap metal in 15 centi metre layer including filling voids with Crushed sand/grit, ramming, watering etcetera complete.
257	A] Ground Floor
258	Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etcetera complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etcetera (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)
259	A] Ground Floor
260	Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etcetera washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.
261	B] First Floor
262	Filling in plinth and floors with approved excavated material in 15 centi metre. to 20 centi metre layers including watering and compacting etcetera complete.
263	A] Ground Floor
264	Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centi metre to 20 centi metre including watering and compaction etcetera complete.
265	A] Ground Floor
266	providing and Fixing in position JUDGE TABLE in COURT HALL decorative veneer with Malemine polish. One Side drawer with lock shall be made in 12 mm thick Plywood All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use. At First Floor Level Of specified Plan size 0.9m heigth madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish. One side drawer with lock shall be made in 12 mm thick Plywood All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer in charge including maintance of 2 year and material got approved by Executive Engineer before use. At First Floor Level
267	B] First Floor
268	Providing and Fixing in position JUDGE CHAMBER TABLE of Specified Plan size 0.9m heigth madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish, Two Side drawer with lock, 2 Shell Shutter with Lock, keyboard Platform for the Computer shall be made in 12 mm thick Plywood All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer beofre use At First Floor Level
269	B] First Floor
270	Providing and Fixing in position STAFF TABLE of Specified Plan size 0.9m heigth madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish. One side drawer with lock, 2 Shelf Shutter with Lock, keyboard Platform for the Computer shall be made in 12 mm thick Plywood All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use Al First Floor Level
271	B] First Floor
272	Providing and Fixing in position ADVOCATE TABLE of Specified Plan size 0 9m heigth madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunnica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish One side drawer with lock 2 Shelf Shutter with Lock keyboard Platform for the Computer shall be made in 12 mm thick Plywood All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use At First Floor Level
273	B] First Floor
274	Providing & fixing in position conference table of size 1.20X3.60X0.75 m made up of 18 mm thick CENTURY MAKE MARINE PLYWOOD GRADE (IS-710) or equivalent make Plywood as per detailed drawing. Providing, 12 mm glass at top in centre with central support box of a size 0.60X2.7X0.70 m in centre. Use of 4 mm thick laminate of inner portion & 4 mm thick decorative for outer surface with Malemaine Polish All work done as per detailed drawing with necessary chromium coated fitting of approved quality as directed by Engineering in charge etc. complete Rate are inclusive of transportation leads and lifts and labour charges including maintanance of 2 year and material got approved by Exective Engineer Before use. by Exective Engineer Before use. At First Floor Level
275	B] First Floor
276	Providing and Fixing in position 0.6 m Deep FULL HEIGTH STORAGE unit 2.1m Heigth with 0.07m skirting madeup of 18 mm Chick CENTURY MAKE PLY WOOD GARDE (IS-710) Or /Equivalent make, Plywood for the frame work shelf, shutter and back with 18 mm thick as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish. All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
277	B] First Floor
278	Providing and Fixing in position 0.6 m Deep LOW HEIGTH STORAGE unit 09 m Heigth with 0.07m skirting madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make, Plywood for the frame work, shell, shutter and back with 18 mm thick as per detailed drawing, inner portion of 720 Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish All work done as per detailed drawing with necessary chromium coated fating such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
279	B] First Floor
280	Providing and Fixing in position 0,6 m Deep FULL HEIGTH STORAGE unit 2.4 m Heigth with 0.07m skirting in LIBRARY ROOM madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make, Plywood for the frame work, shelf, shutter and back with 18 mm thick as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish with DOOR PANEL consist of 5mm thick glass of 2 m heigth All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
281	B] First Floor
282	Providing and Fixing in position 06 m Deep FULL HEIGTH STORAGE unit 2.1m Heigth with 0.07m skirting in ANTI CHAMBER madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make, Plywood for the frame work, shell, shutter and back with 18 mm thick as per detailed drawing, inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish with Central position consist of 5mm thick, 1.65 m heigth mirror and 2 Drawers and side porton consist of 4 Shelf and 2 Shelf with SS rod for hangng purpose. All work done as per detailed drawing with necessary chromium coated fitting such as hings handles lock etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
283	B] First Floor
284	Providing and Fixing in position BOOK RACK PLATFROM of specified plan size and specified heigth madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malermine polish. All work done as per detailed drawing with necessary chromium coated fitting as regired etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
285	B] First Floor
286	Providing and Fixing in position WITNESS BOX OF size 0.9 X 0.9 X 0.9 in the Court hall madeup of 18 mm thick CENTURY MAKE PLY WOOD GARDE (IS-710) Or Equivalent make as per detailed drawing inner portion of Storage finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with Malemine polish, Teak Wood Blauster and Teak Wood ball over pillar with T.W moulding. All work done as per detailed drawing with necessary chromium coated fitting as reqired etc of approved quality as directed by Engineer In charge including maintance of 2 year and material got approved by Executive Engineer before use.
287	B] First Floor
288	Providing & fixing in position Foot Rest 0.60 x 0 40 x 0.15 m made up of 12 mm thick CENTURY MAKE MARINE PLYWOOD GRADE (IS-710) or equivalent make Plywood with necessary hardware fevicol etc. of approved quality as directed by Engineering in charge Nos etc. complete Rate are inclusive of transportation leads and lifts and labour charges including maintanance of 2 year and material got approved by Exective Engineer Belfore use.
289	B] First Floor
290	Providing & fixing in position Workstation table of Size 3 90 X 0.45 X 0.75 m made up of 18 mm thick CENTURY MAKE MARINE PLYWOOD GRADE (IS-710) or equivalent make. Plywood as per detailed drawing. Inner portion of finish wah Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with malemaine polish 3 drawer with lock and 3 key board made up of 12 mm thick plywood All work done as per detailed drawing with necessary chromium coated fitting of approved quality as directed by Engineering in charge elc. complete Rate are inclusive of transportation leads and lifts and labour charges including maintanance of 2 year and material got approved by Exective Engineer Before use
291	B] First Floor
292	Providing and Fixing Wooden Stage Flooring dias of 18 mm thick double layer CENTURY MAKE MARINE PLYWOOD GRADE (IS-710) or equivalent make plywood resting on 0.33 X 0.33 M Grid of 0.075 X 0.075 m Junglee wood section to be fixed in the floor using veneer laminate to the stage top with malemaine polish all nescessary fitting and fixtures all inclusive etc. Rate are inclusive of transportation leads and lifts and labour charges including maintanance of 2 year and material got approved by Exective Engineer Before use.
293	B] First Floor
294	Providing and fixing 6 millimeter thick flot glass on table top having moulding on edges of required size architectural design and drawing, incuding matrial, labour as directed by Engineer incharge etc. complete. Rate are inclusive of transportation, leads and lifts, and labour charges, including maintanance of 2 years and material got approved by Executive Engineer before use.
295	B] First Floor
296	Providing & fixing in position ADVOCATE ADDRESSING BOX IN COURT HALL OF size 0.60 x 0.45 x 0.6 made up of 18 mm thick CENTURY MAKE MARINE PLYWOOD GRADE (IS-710) or equivalent make. Plywood as per detailed drawing. Inner portion of finish with Sunmica 1 mm thick and outer portion of storage with 4 mm thick decorative veneer with malemaine polish. All work done as per detailed drawing with necessary chromium coated fisting of approved quality as directed by Engineering in charge etc. complete Rate are inclusive of transportation leads and lifts and labour charges including maintanance of 2 year and material got approved by Exective Engineer Before use.
297	B] First Floor
298	Public Seating Chair. - 3 SeaterProviding and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.
299	B] First Floor
300	Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT.
301	B] First Floor
302	Providing & Arrangemnt of Mid Back, ECO CTS Mechanism, Fixed Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery
303	B] First Floor
304	Book Case with Glass Shutter @ 825Lx300Dx1650HTProviding & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2 mili metre thick CRCA with glass pannel in Powder coating finish as per drawing.
305	B] First Floor
306	Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (centi metres) Breadth (centi metres): 100 (centi metres) Height (centi metres): 100 (centi metres) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat
307	B] First Floor
308	Tea Table 900 mli metre X 750 mili metre X 450 mili metre for Mild Steel ante chamber Providing And Fixing Of Tea Table 900 mli metre X 750 mili metre X 450 mili metre With 12 mili metre Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 mili metre thick Veneer Or 1 mili metre thick Mica etcetera
309	B] First Floor
310	Providing and Fixing Vertical Blinds of approved Make and shade of 100 mili metre regular fabric with powder coated aluminium channel with telting Polyvenyle Chloride chain & bottom weight plate with all necessary fixtures and fitting etcetera complete. (Sample to be final by Engineer In-charge prior execution of work)
311	B] First Floor
312	Stool for Lab and Class-IVProviding and fixing 4 legged Lab stool, Legs made of 16 Guage 45 mili metre outer dimension MS Pipe, Duly painted, With a 304 Grade Stainless steel 12 inch wide seat with a 1 inch collar, Height adjustment via a screw. as per design and drawing and instructions of Engineer in charge.
313	B] First Floor Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Maharashtra Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Vertical Extension Of Taluka Court Building At Georai Tq. Georai Dist. Beed (First Floor - 4 Court Hall), Beed-Maharashtra

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Vertical Extension Of Taluka Court Building At Georai Tq. Georai Dist. Beed (First Floor - 4 Court Hall), Beed-Maharashtra

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us