|
| 1 | Sch 'A' Part-I (B/R Works)M & L for light shade or printed vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tile n. exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match alongwith dark shade borders over and including 15mm thick screed bed in CM 1:4 including dismantling of existing tiles, complete all as specified and directed. |
| 2 | M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15mm thick screed bed in CM (1:4) including dismantling of old existing tiles, complete all as specified and directed. |
| 3 | M & L for glazed ceramic coloured tile in vertical surface 350 x250x7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incluidng 10mm thick rendering in CM (1:4) including dismantling of old existing tiles, complete all as specified and directed. |
| 4 | S & F Pre - painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour (multi colour pattern as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing roof sheets, complete all as specified and directed. |
| 5 | S & F Pre - painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour (multi colour pattern as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing roof sheets, complete all as specified and directed. |
| 6 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as specified and directed. |
| 7 | M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection laid to slope of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed. |
| 8 | Demolition of cement concrete (unreinforced) of any description and position not otherwise specifically provided for, complete all as specified and directed. |
| 9 | M & L for providing plain cement concrete type B1, 1:2:4, (using 20mm graded stone aggregate), as in coping, bed block for embedding hold fasts, kneelers, apex stones, Gujjar bandi under roof, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating including necessary form work as required, complete all as specified and directed. |
| 10 | Demolition of brick work or stone/boulder or concrete block masonry including all quoins, arches, pillars, etc. built in cement mortar, complete all as specified and directed. |
| 11 | M&L for Walling of random rubble, uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. |
| 12 | All as per Item No 11.00 here-in-before but except stone. Note: Stone retrieved from demolition will be re - used. |
| 13 | M & L for cement concrete type C2, 1:3:6 (using 40mm graded stone aggregate) as in surface channels and drains, complete all as specified and directed. |
| 14 | M & L for forming fair finshed drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends, complete all as specified and directed. |
| 15 | M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4, complete all as specified and directed. |
| 16 | M & L for Rendering 15 mm thick on fair faces of brick work or concrete surface in CM (1:6), finished even and smooth without using extra cement, complete all as specified and directed. |
| 17 | M & L for Rendering 15 mm thick on fair faces of brick, stone or concrete surface including in CM (1:4), finished even and smooth without using extra cement mixed with WPC, complete all as specified and directed. Note: WPC shall be measured and paid separetely. |
| 18 | M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of 2 mm thick wall care putty, complete all as specified and directed. |
| 19 | M & L for preparation of new plastered wall surface including cornices etc and applying two coats of exterior emulsion all weather proof paint of Apex Ultima of ASIAN or equivelent make of any approved two or more colour (multi colour pattern as approved by GE), over and including a coat of primer, complete all as specified and directed. Note: Building height not exceeding 4 stories and rate shall be included for necessary scaffolding & safety measures where required at site. |
| 20 | Taking down chowkat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 but not exceeding 4.0 sqm each, complete all as specified and directed. |
| 21 | S & F for Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings, complete all as specified and directed. |
| 22 | S & F for aluminium powder coated of any colour door with one or more shutters aluminium section weighing 0.55 kg/m including 5 mm thick plain/coloured/ frosted sheet glass or ACP sheet and stainless steel wiremesh and connected itmes such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long , hinges type B-21 100mm long , suitable handle, alum tower bolt including mortice lock and brass door stopper, complete all as specified and directed. |
| 23 | Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed. |
| 24 | S & F for powder coating of any colour (Thickness or powder coating not less than 50 micron) aluminum anodized three track slinding window with two or more shutter with 4 mm thick plain glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock,etc including 65 X 39.5 X 1.5 mm section for complete frame and rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue including taking down existing old window of any description, complete all as specified and directed. |
| 25 | S & F for aluminium powder coated of any colour window and ventilator with one or more shutters fixed/side hung type without sash bar, aluminium section weighing 0.55 kg/m including 5mm thick plain/coloured/frosted sheet glass, stainless steel wiremesh and connected items such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long, hinges type B-21 100mm long, suitable handle, alum tower bolt, complete all as specified and directed. |
| 26 | S & F for aluminum powder coated of any color fixed partition with frame of size 101.6mm x 44.45mmx1.27mm thick and 101.60mmx44.45mmx1.20mm thick with total height up to 3.20m. The panels shall be made out of 5mm thick plain /tinted(frosted) glass in top & bottom or ACP sheet including necessary jointing cleats, glazing clips , rubber packing, powder coated aluminum snap beading screw etc including dismantling of existing partition of any type and making good to the disturbed portion, complete all as specified and directed.Note :- Minimum thickness of powder coating not less than 50 micron. |
| 27 | M & L for roof trusses (framed), purlins or rafters of Fe 410W (Grade E - 250 quality A) including distance pieces and cleats, complete all as specified and directed. |
| 28 | M & L for Rolled section (Fe 410 - W (Gde 250 quality - A) as in main and cross beams hip and jack rafters, purlins where connected to common rafter and running rails and guide for sliding doors fixed with angle cleats or other connected plates, complete all as specified and directed. |
| 29 | M & L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 30 | M & L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications, complete all as specified and directed. |
| 31 | M & L for factory made solid PVC panel door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheety strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded.sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and directed. |
| 32 | S & F of 100mm long mild steel butt hinges, medium weight cold rolled, complete all as specified and directed. |
| 33 | S & F in repairs stainless steel curtain rod of 20mm dia, complete all as specified and directed. |
| 34 | S & F stainless steel 'T' and 'L' type brackets with finials, complete all as specified and directed. |
| 35 | S & F of 125mm long extruded anodised aluminium alloy handle, fabricated type, complete all as specified and directed. |
| 36 | S & F 125mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 37 | S & F for PVC (SWR) pipes single socketed, in any length with rubber ring joints in valley gutters, 110mm bore, complete all as specified and directed. |
| 38 | S & F for PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors/walls in rain water pipe 110mm dia, complete all as specified and directed. |
| 39 | S & F PVC (SWR) bends/Tee of any radius of 110mm dia, complete all as specified and directed. |
| 40 | Dismantling of wall and ceiling board (fibre, pulp, insulation etc) or insulation boards/slabs blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 41 | M&L for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions, complete all as specified and directed. |
| 42 | M&L for Post ATT treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and directed. |
| 43 | M & L for 15 mm bore galvanized iron water tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down GI tubing 15 mm bore and connections, complete all as specifed and directed. |
| 44 | M & L for 20 mm bore galvanized iron water tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down GI tubing 20 mm bore and connection, complete all as specifed and directed. |
| 45 | S & F in repairs 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches/wall, complete all as specified and directed. |
| 46 | S & F in repairs 110 mm bore PVC (SWR) bends of any radius with access to door, complete all as specified and directed. |
| 47 | S & F in repair viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern) and inlcuding flush pipe set of CP jet with PVC pipe of superior quality, complete all as specified and directed. |
| 48 | S & F in repair 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed. |
| 49 | Supply and fixing in repairs for viterous China wash basin, white flat back, size 550 x 400mm including waste pipe, waste chain and plug and porcelan stopper brackets, complete all as specified and directed. |
| 50 | S & F in repair for 15mm bore brass chromium plated wall mixer fixed with shower rose and connecting to wall mixer, complete all as specified and directed. |
| 51 | S & F in repair for 15 mm bore brass CP wash hand basin mixer hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed. |
| 52 | S & F rotational moulded polythene water storage tank (Cylindrical vertical withclosed top)hoisted and fixed in position of 1000 ltrs capacity fixed with Brass tank nipples, including Ball brass valves suitable for 20 mm bore complete all as specified in SSR Part-I including dismantling of existing tank and removing to store, complete all as specified and directed. |
| 53 | S & F in repair 15mm chromium plated health faucet (hand shower), inlet length 100mm fixed to angle valve with and including decorative choice flexible pipe, wall hanger etc, complete all as specified and directed. |
| 54 | S & F in repairs brass CP shower rose of size 125 mm with swivel joints fixing to steel pipes etc, complete all as specified and directed. |
| 55 | S & F in repair PVC waste pipe 600/900mm long suitable for Wash hand basins and urinals including connecting, complete all as specified and directed. |
| 56 | S & F in repair for PVC connection pipe 15mm dia for wash basin and flushing cistern with ss nuts of length 600 mm, complete all as specified and directed. |
| 57 | S & F in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed. |
| 58 | S & F in repair CP soap dish holder fixed with including chromium plated brass screws, complete all as specified and directed. |
| 59 | S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 60 | S & F in repair Glass corner shelf with tempered glass,stainless steel brackets and polished chrome finish rail, complete all as specified and directed. |
| 61 | S & F in repair for chromium plated tubular towel rail 20 mm dia \\"D\\" type 60 cm long between flange,fixed with screw wooden / plastic cleats, complete all as specified and directed. |
| 62 | S & F in repair SS Towel Ring 300mm dia, complete all as specified and directed. |
| 63 | S & F in repairs concealed type CP Stop valves, 15 mm bore of pipe, cast copper alloy CP, screwed down, high pressure, with long shank and cup, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 64 | S & F in repair 15 mm dia CP bib tap cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed. |
| 65 | S & F in repairs 15mm dia CP angle valve, cast copper alloy, fancy type,chromium plated suitable for iron pipe and one end and PVC connector on other, ISI marked, complete all as specified and directed. |
| 66 | S & F in repairs gun metal globe or Brass gate valve with iron wheel screwed both ends for iron pipe of 15 mm dia, complete all as specified and directed. |
| 67 | S & F in repairs gun metal globe or Brass gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia, complete all as specified and directed. |
| 68 | S & F in repair 600 x 450 mm bevelled edge mirror of selected quality glass mounted on 6mm AC building board of commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 69 | S & F in repair CP grating with floor trap suitable for 75 mm bore floor trap and fixed with white cement in square or circular shape and with provision of hole for waste pipe connection, complete all as specified and directed. |
| 70 | S & F in repairs for 20 mm dia Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass errule and fixed, complete all as specified and directed. |
| 71 | M & L in repair 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed. |
| 72 | S & F 30mm width of flaps continuous (Piano) hinges, mild steel, bright finish or electro galvanised, complete all as specified and directed. |
| 73 | S & F 100mm size aluminium handles, cast type, anodised, complete all as specified and directed. |
| 74 | S & F 75mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 75 | S & F 100mm hasp and staple, mild steel, safety type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified and directed. |
| 76 | M & L for colored chequered cement concrete tiles of size 300 x 300 x 25 mm thick with grey cement and pigment laid over and including 20mm thick cement screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor including dismantling of old tiles incl cement mortar bedding (but not the backing) and removing rubbish off the premises, complete all as specified and directed. |
| 77 | M&L for 75mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone graded stone aggregate) as in sub base for tiling, complete all as specified and directed. |
| 78 | M&L for Light shade Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid over and including 10 mm thick rendering 1:4 CM in dados /skirting jointed in neat cement slurry & pointed in white or coloured cement to match including taking down of old tiles, complete all as specified and directed. |
| 79 | Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc, complete all as specified and directed. |
| 80 | M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 81 | Supply only Liquid water proofing compound conforming to IS, complete all as specified and directed. |
| 82 | M&L for rendering 20mm thick on stone walls other than fair faces in CM (1:6), finished even and smooth without using extra cement, complete all as specified and directed. |
| 83 | M & L for complete removal of existing treatment from wall including cornices and chajjas etc and applying two coats of exterior emulsion weather coat paint of Apex Ultima of Asian or equivalent make of any approved single/ two or more colour (multi colour pattern as approved by GE) over and including a coat of primer, complete all as specified and directed. Note:-Buildings height not exceeding four storey and rate shall be included for necessary scaffolding and safety measures where required at site. |
| 84 | M & L for complete removal of existing treatment from wall surfaces and applying two coats of distemper oil emulssion, white or tinted including clearcolle on surfaces for prepatory to distempering over & including one caot of 2mm thick wall care putty, complete all as specified and directed. |
| 85 | S&F Pressed steel door frame of size 105x60 mm with one or more rebates incl necessary fixing lugs, hinges, lock & strike plate etc, complete all as specified and directed. |
| 86 | S&F Pressed steel door frame of size 125x60 mm with one or more rebates incl necessary fixing lugs, hinges, lock & strike plate etc, complete all as specified and directed. |
| 87 | M&L for 35mm thick 2nd class hard wood plain framed panelled shutter (any No.of panels ),with panels of timber flat on both sides (feather edged )or of veneered particles board medium density ,wood particle board with commercial face veneers ,supplied and fixed to chowkat, complete all as specified and directed. |
| 88 | M&L for 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain any numbers, complete all as specified and directed. |
| 89 | S&F 150mm size aluminium handles,cast type, anodised, complete all as specified and directed. |
| 90 | S&F 150 mm long, aluminium,anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 91 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed. |
| 92 | S & F 150mm long floor door stopper of brass body and tongue with hard drawn steel spring, complete all as specified and directed. |
| 93 | S & F 300mm, mild steel rat tail rod pattern springs including roller and roller plate, complete all as specified and directed. |
| 94 | S&F steel window with side hung shutters including side hinges, steel handle, and steel peg stay complete with glazing bars, dove tailed or welded, complete all as specified and directed. |
| 95 | All as per Item No 94.00 here-in-before but without glazing bars. |
| 96 | S&F steel ventilator with top hung shutter including hinges, steel pegs stag, complete all as specified and directed. |
| 97 | Dismantling of structural steel work of any description, complete all as specified and directed. |
| 98 | S & F steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240, complete all as specified and directed. |
| 99 | S & F MS frame work as in grills gratings, with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars and similar works confirming to Fe290 E-165, etc, complete all as specified and directed. |
| 100 | S&F 3mm thick glass sheet ordinary quality and glazing with oil putty of any size each panel, complete all as specified and directed. |
| 101 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. |
| 102 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed. |
| 103 | M&L applying one coat of synthetic enamel paint on old decorated wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed. |
| 104 | M&L for preparation of old painted steel surfaces over 10cm in width or grith and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 105 | S & F PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenchesor in floor 75mm dia, complete all as specified and directed. |
| 106 | S & F PVC (SWR) bends of any radius of 75mm dia, complete all as specified and directed. |
| 107 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for drain etc in any type of soil, complete all specified and as directed. |
| 108 | M&L for cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in foundation, complete all as specified and directed. |
| 109 | S & F 450 mm bore reinforced concrete pipe class NP-2 laid, jointed with collar in neat cement slurry, complete all as specified and directed. |
| 110 | M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 450mm mm bore including packing under and haunching against the sides of pipe after they are laid and tested, complete all as specified and directed. |
| 111 | Returning filling in including spereeding, levelling, watering and wall ramming in layers n. exc 25cm, complete all as specified and as directed. |
| 112 | Removing of excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified and directed. |
| 113 | Demolition of RCC in any description or ground floor and paving not exc 15cm thick, complete all as specified and directed. |
| 114 | M&L for precast RCC 1:2:4 type B1 as in landings, cover slab,chajjas etc.and similar articles with plain faces set in CM 1:6, complete all as specified and direceted. |
| 115 | M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe 410-W as in columns or beams, complete all as specified and directed. |
| 116 | Sch 'A' Part-II (E/M Works)Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications, complete all as specified and directed. |
| 117 | M&L for Point wiring for one light point/fan point / One bell/ buzzer point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor two single core multi strand flexible cable and 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core cable (green color) as earth lead and including PVC casing and caping medium grade with all fitting (ISI Marked) along with along with modular sunken boxes of reqd size with modular white cover plate with frame including cutting chases to wall making good the disturbed surfaces to match with the existing specification, complete all as specified and directed. |
| 118 | All as per Item No 117.00 here-in-before but for socket out 5 Amps on same board. |
| 119 | All as per Item No.117.00 here-in-before but for socket out 5 Amps on independent board. |
| 120 | All as per Serial item No.117.00 here-in-before but for one 3 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistranded copper cable with 2.5 sqmm single core multistranded FRLS copper cable as earthling lead, complete all as specified and directed. |
| 121 | M&L for point wiring with 4 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 4 Sqmm PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC conduit along with modular sunken boxes of reqd size with modular white cover plate with frame including cutting chases to wall making good the disturbed surfaces to match with the existing specification, complete all as specified and directed. |
| 122 | S & F modular switch piano, 1 module, single pole one way 6Amp, complete all as specified and directed. |
| 123 | S & F modular switch piano, 1 module, single pole one way 16Amp, complete all as specified and directed. |
| 124 | S & F modular socket 2/3 pin, 2 module, 6A, ISI marked, 230 volts, complete all as specified and directed. |
| 125 | S & F modular socket 6/16A, 6 pin, 2 module, ISI marked, 230 Volts, complete all as specified and directed. |
| 126 | S&F modular fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically, complete all as specified and directed. |
| 127 | S & F ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body of size 60x50mm, complete all as specified and directed. |
| 128 | Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and directed. |
| 129 | S & F Lamp holder insulated body PVC/ Polycabonate type with back plate including 15 watt LED bulb, complete all as specified and directed. |
| 130 | S&F in replacement LED Tube light fitting, 1x 20 watts. Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient ready to use pack complete rewired, Premium 20 W LED batten, connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core, including removing old/unsv, complete all as specified and directed. |
| 131 | Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 132 | Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket bend to shape made as required of 32/40mm dia not less than 1.20m long GI pipe, light grade fixed to pole/ wall with FI clamp of size not less than 40x6mm two number with the help of nut & bolts, complete all as sepecified and directed. |
| 133 | Taking out unserviceable ceiling fan and deposit to MES Store, supply and replacement with ceiling fan 230V, 50 Hz, AC, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod and electronic regulator alongwith steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core, 0.75 sqmm PVC insulated copper conductor cable, complete all as specified and directed. |
| 134 | M&L for exhaust fan, 4 blade, heavy duty, double ball bearing, 230V, 50Hz, 250mm sweep having power input 70W speed 1200RPM, with protective bird guard including connecting with three core, 0.75 sqmm PVC insulated copper conductor cable, complete all as sepecified and directed. |
| 135 | Supply and fixing AC Socket with 20 Amp MCB with Sheet metal Enclosure with IP -66 and shock proof, complete all as specified and directed. |
| 136 | M&L in replacement wiring for circuit/submain wiring alongwith earth wire with 2x6.0 sqmm PVC insulated FRLS unsheathed copper conductor two single core multi strand flexible cable and 6.0 sqmm PVC insulated FRLS unsheathed copper conductor single core cable (green color) as earth lead and including PVC conduit along with including cutting chases to wall making good the disturbed surfaces to match with the existing specification, complete all as specified and directed. |
| 137 | M&L for sheet metal enclosure MCB distribution board, double door TPN with IP-66 protection single phase 415 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair, including removing old/unsv, complete all as specified and directed. Note:- MCBs will be measured separately. |
| 138 | M&L for sheet metal enclosure MCB distribution board, double door single pole and neutral with IP-66 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair, including removing old/unsv, complete all as specified and directed. Note:- MCBs will be measured separately. |
| 139 | M&L for MCB TPN 415 volts any rating upto 100 amps, with rupturing capacity 10 KA,including providing thimble for out going cables,including removing old/unsv, complete all as specified and directed. |
| 140 | M&L for MCB single pole and neutral 240 volts any rating upto 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables,including removing old/unsv,complete all as specified and directed. |
| 141 | S & F miniature circuit breaker (MCB) SP, 5 to 32 Amp, 240V, 10KA 'B' curve in the DB complete with connection testing and commissioning, complete all as specified and directed. |
| 142 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed. |
| 143 | Supplying and fixing in replacement service cable 1100 volts grade 16x2 Sqmm heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed. |
| 144 | Supply and lay GI pipe 50mm dia light grade in any length with all GI fittings such as socket, elbow, bend, union, Tee etc laid in trenches/duct/culvert/road crossing etc for protection of cables including removing old unserviceable item, complete all as specified and directed. |
| 145 | M & L for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6 mm burried directly in ground earth pit not less than 2.25 mtr deep below normal ground level with top edge of the plate vertically to a depth not less than 1.5 mtr below ground level connected to connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 including GI pipe 15 mm dia light grade for protection to the extend of 7.5 mtr as earthing lead connecting to equipment with provn charcol and salt complete including PCC chamber with RCC cover watering arrangement with GI pipe 20 mm dia medium grade and MS funnel, including excavation and earth work and returning, filling in including ramming and removal of surplus soil and testing on completion complete. Please Enable Macros to View BoQ information |
