|
| 1 | Earth work in excavation in foundation in ordinary -do- |
| 2 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 3 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 4 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 5 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l. |
| 6 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) centering, shuttering, finishing and reinforcement - All work up to plinth level. |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings,balconies, shelves,chajjas, lintels bands, plain window sills staircases and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 10 | Providing Tor steel reinforcement of 8mm,10mm. ,12mm & 16mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. |
| 11 | 08 MM |
| 12 | 10 MM |
| 13 | 12 MM |
| 14 | Centering and Shuttering including strutting,propping etc and removal of form For….. |
| 15 | Foundations |
| 16 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 17 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 18 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 19 | Suspended floors, roofs, landings, balconies and access platform |
| 20 | Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 21 | Providing desination 100 A brick work with fly ash lime brick (FLAG) conforming to IS 12894 - 1990 (9'' x 4.5'' x 3'') in C.M. (1 : 6) in superstruture and plinth with apporoved qulity of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening material, raking out joints to 15 mm depth, taxes and royalty all complete as per building specification and direction of E/I. |
| 22 | Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I. |
| 23 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 24 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel membersshall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). |
| 25 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle thresholdof mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coatof approved steel primer after pre-treatment of the surface as directedby Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail toeach jamb |
| 26 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 27 | Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l. |
| 28 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 29 | Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar (1: 4) laid and jointed with grey cement slurry including rubbing and polishing complete with : |
| 30 | Providing and laying Ceramic glazed floor tiles of size300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm includingpointing the joints with white cement and matching pigment etc.,complete |
| 31 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. |
| 32 | Providing single layer Naria- tiles in roof including cost of all labour and materials, taxes, all coplete as per building specification and direction of E/I. |
| 33 | Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm |
| 34 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 35 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 36 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. |
| 37 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 38 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plaster surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required washing, cleaning and papering the walls, scaffolding, washing of floors and taxes, all complete as per building specification and direction of E/l. |
| 39 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 40 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 41 | For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittingsshall be paid for separately) Anodised aluminium (anodised transparentor dyed to required shade according to IS:1868, Minimum anodic coating of grade AC15) |
| 42 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete asper the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight notless than 10 kg/ sqm) |
| 43 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 44 | Providing 150 mm wide brick drain -do- |
| 45 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with modular type, Group A |
| 46 | Wiring for light/power plug with 2x4sq.mm FR PVC insulated copper conductor single core cable |
| 47 | Wiring for circuit/submain wiring alongwith earth wire -do- |
| 48 | 2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 49 | 2x2.5 sq.mm + 1x2.5 sq.mm earth wire |
| 50 | 2x4 sq.mm + 1x4 sq.mm earth wire |
| 51 | Supplying and fixing following modular type switch/ socket on the existing switch box/cover |
| 52 | 5/6 amps, one way switch |
| 53 | 15/16 amps, 6 pin socket outlet |
| 54 | Supplying and fixing batten holder including connection etc. as required. |
| 55 | Supplying and fixing 2 pin, 5 amps ceiling rose on existing junction box/ wooden block including connection etc. as required. |
| 56 | ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq.mm FRPVC insulated copper conductor single core cable etc. as required |
| 57 | S/F Modular type stepped tube electronic fan regulator on the existing plate switch box including connection but excluding modular plate etc as required |
| 58 | S/F following way single pole neutral, sheet, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) |
| 59 | 8 way, single door |
| 60 | Earthing with copper earth plate 600mm x 600mm x 3mm thick Including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (but without charcoal or coke and salt) |
| 61 | Extra for using salt and charcoal for GI or copper plate earth electrode as required. |
| 62 | S/F 15/16 watt LED Bulb |
| 63 | 20/22 watt LED Tube Light |
| 64 | Supplying of XLPE alluminium armoured cable with all complete job. 16sqmm, 4 core |
| 65 | Supply of 48\\" (1200 mm) Ceiling Fan Bajaj/Crompton or any other approved make etc without regulator |
| 66 | Supply of 12\\" (300 mm) Metal exhaust Fan Bajaj/Crompton or any other approved make etc |
| 67 | 50/60 W LED Flood light |
| 68 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes concealed work |
| 69 | 15 mm nominal |
| 70 | 20 mm nominal |
| 71 | 25 mm nominal |
| 72 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,external pipes, 25 mm nominal outer dia Pipes |
| 73 | Making holes in walls for laying G.I. pipes and restoring the same after pipe laying with complete job. |
| 74 | a) 125mm thick |
| 75 | b) 250mm thick |
| 76 | Providing and fixing gate valve of approved quality with complete job, 25 mm dia |
| 77 | Supplying Polythene water storage tank of ISI mark (e.g. sintex / Sinter / Himgiri / Gangotri etc.) with cover and locking system. |
| 78 | Providing and fixing male ended 15mm dia brass bib cock with complete job |
| 79 | Providing and fixing 15 mm size C.P. brass pillar cock C.I. body brass spindle pillar cock with complete job(C.I. Body brass spindle) |
| 80 | Providing & Fixing Stainless steel Kitchen sink with complete job. 610x510 mm bowl depth 200 mm |
| 81 | Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other with complete job |
| 82 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: |
| 83 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other with complete job , with 12.50 liter low level PVC Cistern |
| 84 | Providing, fitting and fixing 40mm high vitreous white glazed earthen EWC with p trap of Parry Hindustan or any other approved with seat and lid, 12.5 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 12.5 ltr low level PVC cistern |
| 85 | SFF flat back or angular lipped front vitreous white glazed earthen ware urinal of Hindustan Parrry or any other approved with all complete job. |
| 86 | Supplying fitting and fixing the following items complete with all with complete job |
| 87 | a) Mirror of 6mm thick plate glass600x450mm size |
| 88 | b).Soap Dish |
| 89 | c).Towel rail |
| 90 | S/F/F PVC S.W.R pipe (Supreme) - 110mm |
| 91 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 92 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 93 | a).Door tee- 110mm |
| 94 | b) Dlain bend - 110mm |
| 95 | c)Single tee without door - 110mm |
| 96 | Providing and laying in position cement concret of specified grade excluding the cost of centering and shuttering - All work up to plinth level in foundation with approved quality of stone chips all complete as per building specification and direction of E/l. 1:2:4 - 4 graded stone Aggregate 20mm nominal size |
| 97 | Providing 12mm cement plaster(1:3) & 1.5mm cement punning -do- |
| 98 | Cost of drilling for 200mm x 165mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia borng etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of Engineer Incharge. |
| 99 | (i) From 0 - 50 M |
| 100 | (ii) From 51 - 125 M |
| 101 | (ii) From 126 - 151 M |
| 102 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of requireddia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia |
| 103 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 104 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 105 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp |
| 106 | Supplying 2.0 H.P. submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V±10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. |
| 107 | Supplying fitting and fixing of standered make starter pannel board with arrangement of all necessary protection including all taxes,all complete job as per direction of E/I |
| 108 | 3 Core PVC insulated, PVC sheathed copper conductor flatsubmersible cable |
| 109 | 3 core 4 sq mm |
| 110 | Supplying fitting and fixing lowering 40 mm dia G.L. collumn pipe do do all complere job as per direction of E/I |
| 111 | Carriage cost of Materialsm - |
| 112 | (a) sand Lead-30km |
| 113 | (b) Local Sand - 3KM |
| 114 | (c) stone chips Lead-20km |
| 115 | (d) brick Lead-8km(1k+7p) |
| 116 | (e) S/Metal - 20 KM |
| 117 | Add 18 % GST (in Basic Rate must fill 12) |
| 118 | Add 1% Labour Cess (in Basic Rate must fill 1) Please Enable Macros to View BoQ information |
