|
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 50 meter beyond 1 m from cutting edge |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. layers not exceeding 20cm in depth, consolidation each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m. |
| 4 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 5 | Supplying and filling in plinth with fine sand underfloors including, watering, ramming consolidating and dressing complete. |
| 6 | Dry stone pitching, 225mm thick, including cost of stones and preparation of surface. Nallah stone |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- all work upto plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) |
| 8 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 9 | CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 12mm Cement plaster finished with a floating coat of neat cement of mix: 1 : 3 ( 1 cement : 3 fine sand) |
| 10 | Providing and laying in position machine batched and machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.M-25 grade reinforced cement concrete by using 330 Kg cement per cum of concrete. All works upto floor five level. Crushed stone aggregate |
| 11 | Centering and shuttering including strutting , propping etc. and removal of form for : Foundations, footings, bases of columns etc. for mass concrete |
| 12 | Centering and shuttering including strutting , propping etc. and removal of form for :Columns, pillars, piers, abutments, posts and struts |
| 13 | Centering and shuttering including strutting , propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and centilevers. |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth or above level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in : Cement mortar 1:6 (1 cement :6 coarse sand) |
| 16 | Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in : Cement mortar 1:6 (1 cement :6 coarse sand) + Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 17 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) + Extra for half Brick masonry in superstructure above plinth level upto floor V level. |
| 18 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600mm x 600mm |
| 19 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement.Size of Tile 600mm x 600 mm |
| 20 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete. |
| 22 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position. Second class kail wood |
| 23 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction Engineer-in-charge : Second class kail wood |
| 24 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 25 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class KAIL wood 50mm x12mm |
| 26 | Providing and fixing ISI marked 35mm thick flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. including ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws, |
| 27 | Providing and fixing Second class kail wood 35mm thick panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with providing including ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws, (Shutter area to be measured).excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. |
| 28 | Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked including top cover of 6mm commercial ply wood conforming to IS :303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100mm x 40mmx40 mm on both inner side of pelmet and rawl plugs 75mm long etc. all complete |
| 29 | Providing and fixing bright finished brass door latch with necessary screws etc. complete.300x16x5 mm |
| 30 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 250x10 mm |
| 31 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 150x10 mm |
| 32 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete |
| 33 | Providing and fixing bright finished brass handles with screws etc. complete :125mm |
| 34 | Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete |
| 35 | Providing and fixing PVC rigid foam sheet 1mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive |
| 36 | Cement plaster in coarse sand .12mm cement plaster of mix 1:6 (1 cement :6 coarse sand) |
| 37 | Cement plaster in coarse sand 15mm cement plaster on the rough side of single or half brick wall of mix 1: 4(1 cement :6 coarse sand) |
| 38 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 39 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 40 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 41 | Finishing walls with textured exterior paint of required shade on new work (two or more coats applied @ 3.28 liter/ 10sqm over and including base coat of water proofing cement paint applied @2.20kg/10sqm |
| 42 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 43 | Providing & laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen & the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. Per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).all as per manufacturers’ specification and also including the cost ofmaking openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part-I : 2011 (Board with BIS certification marks) |
| 44 | Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a rpiming coat of approved steel primer all complete. |
| 45 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 46 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 47 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 48 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge. |
| 49 | Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-charge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to S : 1328 BWR type |
| 50 | Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by crisscrossingGI wire. With resin bonded fiber glass wool with density 16 kg/cum |
| 51 | Providing and fixing cupboard shutters 25mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade I Type II) having one side decorative lamination and other side a balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and bright finished stainless steel piano hinges complete as per directions of Engineer- in-charge |
| 52 | Providing and fixing bright finished brass handles with screws etc. complete : 100 mm |
| 53 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete: 50 mm |
| 54 | Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters including fixing with necessary screws etc. complete. Triple strip (Vertical type) |
| 55 | Providing and fixing white vitreous china extended wall mounting Water Closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 6 litre (adjustable to 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 56 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. |
| 57 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mmCP Brass single hole basin mixer |
| 58 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 59 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 40 mm dia |
| 60 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 61 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 62 | Providing and fixing toilet paper holder : C.P. brass of standard size |
| 63 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931, 15mm nominal bore |
| 64 | Providing and fixing brass bib cock of approved quality.15 mm nominal bore |
| 65 | Providing and fixing uplasticized PVC connection pipe with brass unions : 45 cm length, 15 mm nominal bore |
| 66 | Providing and fixing PTMT Soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 67 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms |
| 68 | Providing and fixing soil, waste and vent pipes.100 mm dia Centrifugally Cast (spun) Iron S&S pipe as per IS:3989. |
| 69 | Providing and fixing soil, waste and vent pipes. 75 mm dia Centrifugally Cast (spun) Iron S&S pipe as per IS:3989. |
| 70 | Providing and fixing M.S. holder bat-clamps of approved design to Sand Cast Iron / Cast Iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal sixe) including cost of cutting holes and making good the wall etc :For 100 mm dia. |
| 71 | Providing and fixing M.S. holder bat-clamps of approved design to Sand Cast Iron / Cast Iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal sixe) including cost of cutting holes and making good the wall etc :For 75 mm dia. |
| 72 | Providing and fixing MS stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter. For 100 mm dia pipe |
| 73 | Providing and fixing MS stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter. For 75 mm dia pipe |
| 74 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm dia Sand cast iron S&S as per IS - 3989 |
| 75 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75 mm dia Sand cast iron S&S as per IS - 3989 |
| 76 | Providing and fixing plain bend of required degree.(IS 3989)100 mm dia Sand Cast Iron S&S as per IS:3989. |
| 77 | Providing and fixing plain bend of required degree.(IS 3989)75 mm dia Sand Cast Iron S&S as per IS:3989. |
| 78 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100 mm Sand Cast Iron S&S as per IS:3989. |
| 79 | Providing and fixing single equal plain junction of required degreewith access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75x75x75 mm Sand Cast Iron S&S as per IS:3989. |
| 80 | Providing and fixing terminal guard 100 mm dia Sand Cast Iron S&S as per IS:3989. |
| 81 | Providing and fixing terminal guard 75 mm dia Sand Cast Iron S&S as per IS:3989. |
| 82 | Providing and fixing collar :100 mm Sand cast iron S&S as per IS -3989 |
| 83 | Providing and fixing collar :75 mm Sand cast iron S&S as per IS -3989 |
| 84 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :100 mm |
| 85 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :75 mm |
| 86 | Providing and fixing trap of self cleasing design with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS:3989. |
| 87 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore (M) |
| 88 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 20 mm dia nominal bore (M) |
| 89 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc.Internal work-Exposed on wall :25 mm dia nominal bore b) Medium |
| 90 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete, 20 mm nominal bore |
| 91 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 20 mm nominal bore |
| 92 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore |
| 93 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 94 | Providing and fixing square-mouth S.W. gully trap class SP-1complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design |
| 95 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. coverwith frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 |
| 96 | Providing and fixing PTMT grating of approved quality and colour.Circular type, 125 mm nominal dia with 25 mm waste hole |
| 97 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 98 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) |
| 99 | Supplying and fixing following Piano type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch. Make: Crabtee/Legrand/ North West/Anchor/Havells |
| 100 | Supplying and fixing following Piano type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make: Crabtee/Legrand/ North West/Anchor/Havelles 3 pin 5/6 A socket outlet |
| 101 | Supplying and fixing following size modules, GI box along with modular base and cover plate for modular switches in recess etc.6 module (200mmX 75mm) |
| 102 | Supplying and fixing following Piano type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make: Crabtee/Legrand/ North West/Anchor/Havelles 15/16 A switch |
| 103 | Supplying and fixing following Piano type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make: Crabtee/Legrand/ North West/Anchor/Havells/ Any reputed make 6 pin 15/16 A socket outlet |
| 104 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 20 Amp. Make: L&T/ABB/ Schneider /Havells |
| 105 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 10 Amp. Make: L&T/ABB/ Schneider /Havells/ any reputed make |
| 106 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 Amp. Make: L&T/ABB/ Schneider /Havells/ any reputed make |
| 107 | Installation, testing and commissioning of pre wired, fluorescent fitting / compact fluorescent fitting/LED tube fittings of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. LED tube light fitting 4 Feet with battery back up |
| 108 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper Conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.Make: Any reputed make |
| 109 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 10 sq. mm + 1 X 6 sq. mm earth wire. Make: Havells/L&T/Polycab/ Finolex/KEI. Conduit-Plaza/Ajanta Plast/ Any reputed make |
| 110 | Wiring for light /power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit alongwith 1 No.4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 111 | Supplying 4 pole MCCB 125 A, 36 KA, Any ISI reputed make |
| 112 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box including connections as required |
| 113 | Installation of Exhaust fan in the existing opening including making good the damage, connection, testing and commissioning etc. as required |
| 114 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required. |
| 115 | Extra for fixing louvers/ shutters complete with frame for a exhaust fan of all sizes |
| 116 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 117 | Out door cable jointing kit with cast resin compounds with lugs for 3 and half core 35 Sq.mm Aluminium cable 1.1 KV Grade |
| 118 | Earthing with GI earth npipe 4.5 Mtr. Long 40 mm dia including accessories and providing masonary enclosure with cover plate having locking arranGeMent and watering pipe with charcoal/ coke, salt as required |
| 119 | Supply of PVC sheathed pvc insulated XLPE armoured Aluminium conductor cable of size 3.5 core 35 sqmm, 1100 V grade as per IS7098-Part I with latest ammendments . Make : Havells/ Finolex/ Polycab/KEI/ Any reputed make |
| 120 | Supplying 1200mm Sweep ceiling fan with electronic regulator, Any rteputed make |
| 121 | Supplying of 300 mm Ventilating/Exhaust Fan Metalic Body Make: Any reputed make |
| 122 | Supplying LED tube light fitting 4 feet, 18 watt , Any reputed ISI make |
| 123 | Supplying of 70 Watt Steet LED light , Any reputed ISI make |
| 124 | Supplying of Geyser of 35 Ltr. Capacity 5 star rating Make: Bajaj/Havells/Crompton/Racold/Venus/ V guard/ any Reputed ISI make |
| 125 | Supplying of wall mounting fan Make: Bajaj/Havells/Crompton any Reputed ISI make |
| 126 | Supplying 9 watt LED Bulb , Any reputed ISI make |
| 127 | 200 amp power distribution box, any reputed ISI make Please Enable Macros to View BoQ information |
