|
| 1 | Excavation in trenches n exc 1.5 m in depth in any type of soil; for foundation, etc. and getting out including bailing/pumping /dewatering(if required) of water complete all as specified and directed by Engr-In-Charge. |
| 2 | Excavation in trenches exc 1.5 m in depth and n exc 3.00 m in any type of soil ; for foundation, etc. and getting out including baling/pumping /dewatering(if required) of water complete all as specified and directed by Engr-In-Charge. |
| 3 | Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engr-In-Charge. |
| 4 | M & L for spreading and leveling in layers n.exc 25cm thick and well ramming including watering as required under floors (in floor with available earth from excavation) complete all as specified and directed by Engr-In-Charge. |
| 5 | Removing excavated material exc 50m and not exc 250m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed. |
| 6 | M&L for PCC 1:4:8 type D2 40mm stone aggregate filling mass concrete in foundation complete all as specified and directed by Engr-In-Charge. |
| 7 | Material and labour for providing Reinforced Cement Concrete (Design Mix) M-30 using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc complete all as specified and directed by Engr-In-Charge. |
| 8 | M & L for Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed by Engr-In-Charge. |
| 9 | Material and labour for providing Reinforced Cement Concrete (Design Mix) M-30 using 20 mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-In-Charge. |
| 10 | Material and labour for providing Reinforced Cement Concrete (Design Mix) M-30 using 20 mm graded aggregate as in beams, cantilever, chajja,lintels over 1.5 m complete all as specified and directed by Engr-In-Charge. |
| 11 | Material and labour for providing Reinforced Cement Concrete (Design Mix) M-30 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floor, roof, landing, balcknies, conopies, decks, slab and in shelves and like complete all as specified and directed by Engr-In-Charge. |
| 12 | M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; rough finished vertical or to batter complete all as specified and directed by Engr-In-Charge. |
| 13 | M & L Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished vertical or to batter complete all as specified and directed by Engr-In-Charge. |
| 14 | M & L formwork to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and directed by Engr-In-Charge. |
| 15 | M & L formwork to soffits of suspended slabs such as roof slabs, floor slabs, la ndings and similar work; not exceeding 200 mm thick (Horizontal or slopping) for rough finished flat surfaces of concrete complete all as specified and directed by Engr-In-Charge. |
| 16 | Material and labour for 6 to 8 mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engr-In-Charge. |
| 17 | Material and labour for 10 mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engr-In-Charge. |
| 18 | Material and labour for 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engr-In-Charge. |
| 19 | Material and labour for 100 mm thick sand filling over 150 Micro ploythene film over rammed earth under floors or in foundation including watering and consolidation as specified and directed by Engr-In-Charge. |
| 20 | M&L for hard core of broken brick of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces as s complete all as specified and directed by Engr-In-Charge. |
| 21 | Material and labour for providing 75 mm thick cement concrete (1:3:6) type C2 using 40mm graded aggregate as in plinth protection surfaces even and smooth without using extra cement including provision of construction joints complete all as specified and directed by Engr-In-Charge. |
| 22 | M & L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and directed by Engr-In-Charge. |
| 23 | M & L Cement concrete 100 mm thick type D-2, 1:4:8 (40mm graded aggregate) as in sub-floors, sub bases, floors and pavings, etc complete all as specified and directed by Engr-In-Charge. |
| 24 | S&F ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, (400 X400 mm) as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge |
| 25 | M&L for granite, 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms etc.over and including 20 mm thick screed bed in cement mortar 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete as specified and directed. |
| 26 | M & L brick work with fly ash bricks, straight or curved on plan exceeding 6 metre mean radius built in CM 1:6 complete all as specified and directed by Engr-In-Charge. |
| 27 | M & L for Rendering 15mm thick in cement mortar 1:4 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed by Engr-In-Charge. |
| 28 | M & L for Rendering 15mm thick in cement mortar 1:6 on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed by Engr-In Charge. |
| 29 | M&L for 5 mm thick plaster on ceiling/ concrete surfaces in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge. |
| 30 | M&L for preparation of Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed by Engr-In-Charge. |
| 31 | M&L for Preparation of new plastered surfaces and applying applying wall care putty on ceiling of 3 mm thickness over plastered surface to prepare the surface even and smooth and apply one coat of OBD on ceiling as specified & directed by Engr-In-Charge. |
| 32 | M&L for preparation of new surfaces including 3 mm wall care putty on walls over plastered surfaces to prepare surface for receiving distempering two or more coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification including all preparation complete all as specified & directed by Engr-In-Charge. |
| 33 | M & L Rendering 1:3 of mortar 10 mm thick for roof with water proofing compound complete all as specified & directed by Engr-In-Charge. |
| 34 | OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm.(a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification.(b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger PaintsNote : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE.(iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years. |
| 35 | Supply of SBR waterproofing compound @ 2% of per Kg cement used complete all as specified and directed by Engineer - in - Charge.Make:- Fosroc / Sika/ Choksey / Chemsol / Bostik/ STP |
| 36 | S&F factory made uPVC white colour double shutter (one glazig and one gauzing) openable window area exc 1.00 sqm but not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm) with or without provisioning of opening for cooler, window profile with hollow section with multi chamber, frame (60mmx58mm) T profile (one vertical length in between two shutters) (60mmx74mm) glazing bead (35mmx20mm) will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc making arrangement for fixing of hardware, EPDM gasket 1.2 +- 0.2mm thick, galvanised steel frame (28mmx21.5mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, 5mm thick glazing with selected quality glass complete all as specified and directed by Engineer-in-Charge.Note:- The rate quoted by contractor excludes cost of glass /wiremesh and includes all other connected accessories net opening will be measured for payment purpose. |
| 37 | S&F factory made uPVC white colour openable ventilator/window area not exc 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm), window profile with hollow section with multi chamber, frame (60mmx58mm) T profile (one vertical length in between two shutters) (60mmx74mm) glazing bead (35mmx20mm) will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc making arrangement for fixing of hardware, EPDM gasket 1.2 +- 0.2mm thick, galvanised steel frame (28mmx21.5mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, 5mm thick glazing with selected quality glass complete all as specified and directed by Engineer-in-Charge.Note:- The rate quoted by contractor excludes cost of glass /wiremesh and includes all other connected accessories net opening will be measured for payment purpose. |
| 38 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 39 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 40 | M & L for 4.8 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters) in Squares n.exc 0.5 sqm each complete all as specified and directed by engr-in-charge. |
| 41 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge |
| 42 | S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge. |
| 43 | Supply and fixing 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by engr-in-charge. |
| 44 | S & F 150 mm long aluminium handles, fabricated type, anodised complete all as specified and directed by engr-in-charge. |
| 45 | S&F 100 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed by engr-in-charge. |
| 46 | S & F Floor door stopper of aluminium , 75-100 mm cast iron body, with hard drawn steel spring complete all as specified and directed by engr-in-charge. |
| 47 | S&F 250 mm long , Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by engr-in-charge. |
| 48 | S&F Door closer hydraulically regulated, Aluminium (Extruded section body) designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified. |
| 49 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 150mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 150mm -02 Nos per leaf Please Enable Macros to View BoQ information |
| 51 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 150mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 150mm -02 Nos per leaf Please Enable Macros to View BoQ information |
