|
| 1 | Schedule 'A' Part-I (B/R itmes) Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. ,complete all as specified and as directed. |
| 2 | Material and labour for rendering 15mm thick on any faces of brick work or concrete wall surfaces in cement mortar (1:6) and finished even and smooth without using extra cement, complete, all as specified and as directed. |
| 3 | Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge. |
| 4 | Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens,nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groovecomplete as per specifications and direction. |
| 5 | Material and labour rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. ( Note- WPC shall be measured paid for separately) |
| 6 | Supply only water proofing compound ,complete all as specified and as directed.. |
| 7 | Material and labour for rendering 05 mm thick on any faces of brick work or concrete ceiling surfaces in cement mortar (1:3) and finished even and smooth without using extra cement complete, all as specified and as directed. |
| 8 | Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of acrylic distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, complete all as specified and as directed by the Engineer-in-Charge. |
| 9 | Material and labour for preparation of new plastered /concrete surface of wall applying of two coats of cement base paint over a coat of alkali resistant primer, complete, all as specified and as directed. |
| 10 | Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of ceiling, chajjas, roof projection ceiling etc., complete all as specified and as directed. |
| 11 | Material and labour for preparing surfaces plastered or unplastered washing ,rubbing down and stopping of distempered and painted surface and applying two coat of acrylic distemper over 2 mm thick putty complete all as specified and as directed. |
| 12 | Material and labour for preparing surfaces plastered or unplastered washing ,rubbing down and stopping of distempered and painted surface and applying two coat of cement based paint complete all as specified and as directed. |
| 13 | Material and labour for preparing old surfaces of ceiling, plastered or unplastered and applying two coats of white wash on ceiling complete all as specified and as directed. |
| 14 | Material and labour for formwork to chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges, work in rough finished flat surfaces of concrete complete all as specified and as directed. |
| 15 | Material & Labour reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, graded stone aggregate as in chajjas,Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels,balustrade, and the like complete all as specified and directed. |
| 16 | Material and labour for TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete all as specified and directed. |
| 17 | Material and labour TMT steel bars 6mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed . |
| 18 | Material and labour formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc., also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and as directed . |
| 19 | Material and labour formwork to soffits of suspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 centimetre thick (horizontal or sloping) flat for rough finished surfaces of concrete ,complete all as specified and as directed. |
| 20 | Material and labour reinforced cement concrete M-25 (design Mix) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed . |
| 21 | Demolition reinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, and similar suspended work complete all as specified and as directed . |
| 22 | Material & Labour for Reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the likedack slab , complete all as specified and directed. |
| 23 | Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , complete, all as specified and as directed. |
| 24 | Material and labour brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 , complete, all as specified and as directed. |
| 25 | All as per serial item No. 24 here in befor but except bricks (old serviceable bricks obtained from serial item No 23 above including removing motar, cleaning the bricks with water,shall be used ), complete all as specified and as directed . |
| 26 | Material & Labour brick work with sub class 'B' old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 ,complete all as specified and as directed. |
| 27 | Material and labour plain cement concrete 1:2:4 type B–1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork for rough finished surfaces of concrete complete, all as specified and as directed. |
| 28 | Material and labour for providing 75 mm thick cement concrete 1:3:6, type C–1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight , complete, all as specified and as directed. |
| 29 | Demolition of Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge. |
| 30 | Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete, all as specified and as directed. |
| 31 | Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish, complete, all as specified and as directed. |
| 32 | Cutting holes in brick walls exc half brick wall but not exc one brick wall built in cement mortar or cement lime mortar and stone walls built in lime mortar upto 30 cm depth for inserting holdfasts or embedding fencing posts and making good dismantled portion in cement mortar (1:3) or cement concrete 1:2:4 Type B-1 as required ® complete, all as specified and as directed by the Engineer-in-Charge. |
| 33 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) , complete, all as specified and as directed. |
| 34 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed . |
| 35 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat section of size 50 mm x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 36 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 37 | Supply and fixing of butt hinges 100mm long of Mild steel, medium weight, complete all as specified and as directed. |
| 38 | Supply and fixing for aluminium anodised barrel tower bolts of extruded section and fixed of 150mm long complete all as specified and directed. |
| 39 | Supply and fixing 150 mm long aluminium handle cast type anodised, complete, all as specified and as directed. |
| 40 | Material and labour 12mm thick prelaminated particle board interier grade (grade–1) confirming IS 14587 prelaminated both side with decorative choice lamination and fixed to aluminium door shutter with glazing clips, rubber , complete, all as specified and as directed. |
| 41 | Supply and fixing 100mm long mortice latch with two levers (vertical type),mild steel body complete all as specified and directed. |
| 42 | Supply and fixing for aluminium frame / shutter for door, window, ventilator, partition , CUPBOARD with one or more rebats including joint cleat and all necessary items including taking out existing shutters complete all as specified. |
| 43 | Material and labour sheet glass 4.8mm thick tinted quality and glazing with aluminium snap beading, rubber gasket in square not exc 0.5 sqm in each pane , complete, all as specified and as directed. |
| 44 | Material and labour PCC 1:3:6 type B-I using 20mm graded stone agg as in holdfasts complete all as specified. |
| 45 | Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised mild steel wire staple, complete, all as specified and as directed. |
| 46 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed . |
| 47 | Material and labour machine cut kota stone slab 18 to 22 mm thick (stone slab size not less than 550mm x 550mm) in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 ,complete all as specified and directed. |
| 48 | Material and labour machine cut kota stone slab 18 to 22 mm thick ( kota stone shall be cut from size not less than 550mm x 550mm) in skirting , set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick rendering in CM 1:4 ,complete all as specified and directed. |
| 49 | Material and labour 75 mm thick PCC 1:4:8 Type D–2 using 40mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement ,complete all as specified and as directed. |
| 50 | Material and labour PCC 1:4:8 Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge. |
| 51 | Material and labour for vibratory rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick complete all as specified and as directed . |
| 52 | Material and labour glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/ skirtings /dados of size 300 x 600 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on faces of brick /concrete surfaces in cement mortar (1:4) , complete, all as specified and as directed. |
| 53 | Material and labour for black granite (of any type) tiles 16–18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types over 15mm thick screed bed in cement mortar 1:6 and including rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations and including making holes for gas pipes or WHB outlet /inlet , complete, all as specified and as directed. |
| 54 | Material and labour for 8 to 10mm thick heavy duty (digital) vitrified coloured paver tiles of size 300mm x 300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and as directed.Make: Endura of Johnson or Durastone of Somany or equivalent make given in App ‘B’ |
| 55 | Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed , complete, all as specified and as directed. |
| 56 | Supply and fixing fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, ISI marked, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe , complete, all as specified and as directed. |
| 57 | Material and labour 75mm bore PVC (SWR) floor trap with and including CP grating including jointing with solvent cement including fixed in cement concrete ,complete all as specified and as directed.. |
| 58 | Supply and fixing 15mm bore cast copper alloy chromium plated angular stop valves with capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions, complete all as specified and as directed. |
| 59 | Supply and fixing of ISI marked 20mm bore stop valve, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed . |
| 60 | Supply and fixing in replacement of 600mmx450mm bevelled edge mirror 5mm thick of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed . |
| 61 | Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm , complete, all as specified and as directed. |
| 62 | Supply and fixing brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete, all as specified and as directed. |
| 63 | Supply and fixing of vitreous china wash hand basin white with pedestal, ISI marked, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing of waste fitting, etc complete all as specified and as directed by the Engineer-in-Charge. |
| 64 | Supply and fixing soap dish, brass chromium plated, approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws , complete, all as specified and as directed. |
| 65 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge |
| 66 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge |
| 67 | Material and labour galvanised iron tubing 15 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete, all as specified and as directed. |
| 68 | Material and labour galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete, all as specified and as directed. |
| 69 | Supply and fixing , water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including disconnecting and dismantling of existing water tanks and removing from site all as specified in SSR Part–I , complete all as specified and as directed by the Engineer-in-Charge.Note : - The colour of tanks shall be white colour . |
| 70 | Supply and fixing 75mm bore PVC (SWR) bends of any radius, complete, all as specified and as directed. |
| 71 | Supply and fixing stainless steel curtain rod 25mm dia having wall thickness 1.00mm fixed with and including stainless steel decorative brackets, two lotto for each rod length at both end etc as in repair complete all as specified and as directed. |
| 72 | Demolition and breaking up SWR drain pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) ,complete all as specified and as directed. |
| 73 | Supply and fixing 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches including necessary excavation, returning filling and removal etc complete, all as specified and as directed. |
| 74 | Supply and fixing 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall ,complete all as specified and as directed. |
| 75 | Supply and fixing 110mm bore PVC (SWR) bends of any radius, complete, all as specified and as directed. |
| 76 | Material and labour for MS framed work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and directed |
| 77 | Dismantling steel sheeting (corrugated, semicorrugated, etc.) in roof coverings including ridges, complete all as specified and as directed by the Engineer-in-Charge. |
| 78 | Supply and fixing pre–painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, having zinc coating 150 gm per sqm (Az–150) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 79 | Supply and Fixing mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and as directed. |
| 80 | Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing, steps, cills, sunshades, shelves, lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth ,complete all as specified and as directed.. |
| 81 | Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed . |
| 82 | Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed and gauged skeleton shutter fabricated from following sections :-(a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf .(c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame .(viii) Two coat of Synthetic enamel paint over one coat of red oxide primer.(ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws .(x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window.(xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above.(iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type. |
| 83 | Supply and fixing for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 84 | Supply and fixing Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps when open in 40mm complete all as specified and as directed. |
| 85 | Supply and fixing Aluminium CP fancy type handle 100mm size complete all as specified and as directed . |
| 86 | Dismantling wrought iron of mild steel work of any description not otherwise provided for complete all as specified and as directed . |
| 87 | Material & Labour for Stainless steel plate rack of size 31\\" x 30\\" x 10\\" of load capacity not less than 30 kg including fixing with stainless stell screws including taking down of old plate rack of any description , ,complete all as specified and directed. |
| 88 | Supply and fixing of 18mm thick PVC sheet (density not less than 600 Cum) having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including dismanteling existing board any type complete all as specified and directed. NOTE: - Material manufacture test certificate alongwith purchase voucher should be produced before execution of work. |
| 89 | Supply and fixing as in repair mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet (all as per godrej pattern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer–in–Charge. |
| 90 | Schedule 'A' Part-II (E/M itmes)Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc., complete all as specified and as directed by the Engineer-in-Charge. |
| 91 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately . |
| 92 | Description all as per serial item No.91 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed. |
| 93 | Description all as per serial item No.91 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed. |
| 94 | Description all as per serial item No.91 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 95 | Description all as per srl item No 91 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 96 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directed. |
| 97 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed. |
| 98 | Supply and fixing of modular socket outlet multipin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed. |
| 99 | Supply and fixing of modular socket outlet multipin combined, (6pin), 16 Amps, one way, two module, 230 volts complete all as specified and as directed. |
| 100 | Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed. |
| 101 | Supply and fixing as in repair electronic Fan regulator, modular 100 watts, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed . |
| 102 | Supply and fixing in repair LED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed . Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx 'B'. |
| 103 | Supply and fixing sheet metal enclosure triple pole & neutral(TPN) IP-54 With and including MCB TPN-63 Amps, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed . Cat part No.811857 of make Indo Asian or equivalent make given in Appx 'B'. |
| 104 | Supply and fixing MCB TPN, 63 Amps, 240 volt, 10 KA, 'C' curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed . |
| 105 | Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB , complete all as specified and as directed by the Engineer-in-Charge. Cat Part No 811008 of make Indo Asian or equivalent in make given in Appx 'B'. |
| 106 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve including removing old unserviceable enclosure, complete all as specified and as directed by the Engineer-in-Charge. Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx 'B'. |
| 107 | Supply and Laying or fixing or passing through pipe for cable XLPE insulated, armoured heavy duty electric cable with multistranded aluminium conductor 1100 volts grade 4 core of size 25 Sq.mm, complete all as specified and as directed. |
| 108 | Taking down exhaust fan, cleaning the same and refixing after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed. |
| 109 | Taking down electric geyser and refixing the same after completion of work at required position, complete all as specified and as directed. |
| 110 | Taking down ceiling fan, cleaning the same and refixing after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed. |
| 111 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth lead of 4mm dia GI wire by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge and earth testing on completion . |
| 112 | Note:- Amount of credit of Rs.35,442.00 for retrieved materials is mentioned in Schedule of Credit Page No. 123 & 124 of tender doCubic metre ents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
