|
| 1 | B/R WORKS |
| 2 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in SOFT/LOOSE soil complete, all as specified. |
| 3 | Excavation in trenches n. exc 1.5 m wide for foundations not exceeding 1.5 m deep and getting out in SOFT/LOOSE soil complete, all as specified. |
| 4 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in SOFT/LOOSE soil complete, all as specified. |
| 5 | Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete, all as specified. |
| 6 | Removal of excavated surplus spoil to a distance n. exc. 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified. |
| 7 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in kitchen shelves and the like complete all as specified. |
| 8 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates as in as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified. |
| 9 | PCC type C-2 (1:3:6), using (40 mm graded stone aggregates) as in foundation, complete all as specified. |
| 10 | PCC type D-2 (1:4:8), using (40 mm graded stone aggregates) as in foundation, complete all as specified. |
| 11 | Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in kerbs around tiles and paver block and in coping benching etc slightly rounded or chamfered angles and throating complete all as specified. |
| 12 | Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified. |
| 13 | Cutting holes into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required. |
| 14 | Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and wood grain colour PVC sheet for top rail, lock rail and bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement as specified in SSR Part II, complete all all as specified. |
| 15 | Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified. |
| 16 | Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 200 mm long, complete all as specified. |
| 17 | Aluminium anodised barrel tower bolt of extruded section 200mm long, ISI marked, complete all as specified. |
| 18 | Stainless steel pull handle dia of pipe 3 cm and 45 cm long with necessary fittings complete all as specified. |
| 19 | Stainless steel locking arrangement of glass door complete all as specified. |
| 20 | Stainless steel 75 mm long butt hinges with stainless steel screws, ISI marked complete all as specified. |
| 21 | Extruded aluminium anodised handles fabricated type with plate 150 mm long, ISI marked complete all as specified. |
| 22 | Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples all as specified |
| 23 | Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates quality confirming to grade Fe-290-Gde E-165, complete all as specified. |
| 24 | Mild steel rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to grade Fe-290-Gde E-165, complete all as specified. |
| 25 | Framed work as in doors or gates of angle or other section with gusset plates, rails,braces,etc complete drilled for fixing of steel sheeting or other covering,Doors,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides and hanging also fastening and fixing complete |
| 26 | Stainless steel framed work as in railing, post , steel bowl, steel nut bolts, grills gate of any shape or section made of grade 304 with all connecting items completely drilled or welded for fixing of section in concrete, brick work , granite etc complete all as specified.Note : Make good to the existing damage surface without extra cost. |
| 27 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 28 | Powder coated aluminium frame for doors, windows, ventilators, fixed glazing with one or more rebates including joining cleat for fixing, fixed to opening with suitable size steel screws and rawl plugs etc., (aluminium section not less than 2 mm) complete all as specified. |
| 29 | Powder coated aluminium window and ventilator shutters side hung type with styles & rails , anodised alumnium glazing snap beading , rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified. NOTES: (a) Each shutter shall have 2 Nos. 125 mm long almn handles and 02 No. 75 mm size stainless steel/almn butt hinges & one no. almn hook & eye.(b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ.(c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron. |
| 30 | Powder coated aluminium door or window shutters with styles & rails , anodised alumnium glazing snap beading , rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified. NOTES: (a) Each shutter shall have 2 Nos. 125 mm long almn handles and 03 No. 75 mm size stainless steel/almn butt hinges.(b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ.(c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron. |
| 31 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws comlete all as specified. |
| 32 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws comlete all as specified. |
| 33 | Anodised powder coated GI snap grid frame work of size 605mm x 605mm for false ceiling complete with acessories all as specified and shown on serial page No.186 of MES Schedule Part-II. |
| 34 | Hangers 2-6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 35 | 4-6 mm thick Gypsum-board, multipurpose, fixed in grid frme work ceilings as panels, complete all as specified. |
| 36 | Aluminium composite panel sheet 5-6 mm thick of shade approved by GE cut to shape and fixed in position as almn door shutter panel/partition complete all as specified. |
| 37 | Plain solid acylic sheet thicknees 6 mm of any colour fixed with aluminium beading 4-5 cm wide over framed structure with steel / rustless screw complete all as specified. |
| 38 | 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, as in floors or similar locations finished even and fair without using extra cement, complete all as specified. |
| 39 | 40 mm thick, cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate even and smooth as in flooring ,complete all as specified. |
| 40 | 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & fair/boom finish without using extra cement ,complete all as specified. |
| 41 | 100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, as in sub base of floor etc complete all as specified and directed. |
| 42 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., and brushing a coat of cement slurry with 3 kg of cement per Sq.m, complete all as specified. |
| 43 | Machine cut Kota stone slab flooring 18-22 mm thick and of size not less than 550x550 mm, in floors, laid over over & including 20 mm thick (average thickness) cement mortar (1:6) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding & finishing mirror polished complete, all as specified. |
| 44 | Granite jet black shade, 16-20 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified |
| 45 | Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified. |
| 46 | Glazed ceramic coloured tiles 7-8 mm thick, area of each tile exc. 0.13 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified |
| 47 | Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 Sq.m but n. exc. 0.11 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 48 | Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 0.18 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 49 | Anti skid joint free ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 Sq.m but n. exc. 0.11 Sq.m, for disable person (as use in hospital etc ) laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 50 | 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete. |
| 51 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair using water proofing compound on walls in cement mortar (1:4), complete all as specified.NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ. |
| 52 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6), complete all as specified. |
| 53 | Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two layer & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer. |
| 54 | Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two layer & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer. |
| 55 | Prepration of new plasterd wall surfaces of any description & applying Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer complete all specified |
| 56 | Complete removal of existing treatment with mechenical scraper of any description, applying Two coats of exterior acrylic emulson over and including a coat of water based exterior primer & including prepration of wall surfaces of any description in disruptive/camouflaging pattern of four / three shades complete all specified. |
| 57 | Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron (new) surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified. |
| 58 | Peparation of old painted steel & iron surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified. |
| 59 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified. |
| 60 | Toughned glass thickness 10 mm as in hinged doors, partition automatic doors and similar work including cutting to shape, drilling hole required. |
| 61 | Sheet glass 5 mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified. |
| 62 | Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified of size: - |
| 63 | 15 mm bore |
| 64 | 20 mm bore |
| 65 | 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, complete all as specified including the following acessories: -(i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified.(iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, complete all as specified.(iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, complete all as specified. |
| 66 | Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe,complete. |
| 67 | Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete. |
| 68 | Pillar tap, cast copper alloy chromium plated fancy type, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete. |
| 69 | Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, ISI marked, white, with integral foot rests (excluding flushing cistern and flush pipe), 110x125 size uPVC 'P' trap & necessary joints, lime concrete, complete all as specified. |
| 70 | Vitreous China urinal , bowl type (back) , half stall of size 465 x 355 x 265 mm white (miniumum), with grating and union for discharge pipe complete including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 including spreader all as specified. |
| 71 | Vitreous China wash basin, white, flat back, size 550 x 355 x 400 mm, ISI marked, including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe, IN REPLACEMENT, complete all as specified. complete all as specified. |
| 72 | PVC low level flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, IN REPLACEMENT ,complete. |
| 73 | Looking mirror 600 x 450 mm, selected quality glass 5.5 mm thick, mounted on PVC ply not less than 6 mm thick, and provision of PVC frame alround fixed with chromium plated brass screws and rawl plugs, complete all as specified. |
| 74 | Double action floor door spring, hydraulically regulated, made of 1.25 mm thick aluminium alloy sheet, foundation box main body with stainless steel cover, governing pivot made of brass, rest of part made out of heavy duty mild steel, ISI marked, complete. |
| 75 | Soap dish stainless steel chromium plated decorative type complete all as specified and directed. |
| 76 | PVC connections 15 mm size of length 450 mm with PTMT nuts, complete all as specified. |
| 77 | uPVC pipes, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors / fixed to wall as SWR pipes, complete all as specified of size: - |
| 78 | 75 mm external dia pipe |
| 79 | 110 mm external dia pipe |
| 80 | uPVC/PVC bend any radius, complete all as specified. suitable for uPVC soil waste discharge pipes, of size: |
| 81 | 75 mm external dia pipe |
| 82 | 110 mm external dia pipe |
| 83 | uPVC/PVC junction single (Single T) equal or unequal 110mm external dia complete |
| 84 | uPVC/PVC vent cowl 110 mm external dia, complete all as specified. |
| 85 | 75mm dia uPVC / PVC floor trap including jointing with solvent and embedding in cement concrete type B-1 (1:2:4) complete all as specified. |
| 86 | E/M WORKS |
| 87 | Point wiring with multi-stranded copper conductor, single core, FRLSH PVC insulated and unsheathed cable, including FRLSH PVC insulated unsheathed stranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, with and including GI terminal modular boxes made out of 1.2mm thick MS sheet concealed in wall modular metal flush box & including modular cover plate with frame having necessary cutting for fixing switches/ sockets comprising the following: - |
| 88 | One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. or for bell/buzzer with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit not less than 20mm dia all as specified. |
| 89 | One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified. |
| 90 | One socket outlet three pin, 6/16 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit not less than 20mm dia all as specified. |
| 91 | NOTES: (a) Switch(es) & socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. (b) GI boxes shall be fixed flush to walls in position with cement mortar (1:4). |
| 92 | Switch modular type single pole one way, 6 Amp, 1 module complete all as specified. |
| 93 | Switch modular type single pole one way, 16 Amp, 1 module complete all as specified. |
| 94 | Socket outlet multipurpose having provision for 2&3 pin, 6 Amp, 2 Module complete all as specified. |
| 95 | Fan regulator modular type (electronic) suitable for 48”/56” sweep fan, step type, two module, complete all as specified. |
| 96 | Ceiling rose, surface bakelite, 65 x 50mm, three terminals complete, all as specified. |
| 97 | Sheet metal enclosure SPN, 4 way with 100 Amp rated bus bar, 240 V, double door type for DB for fixing MCB’s, isolators etc., having IP-43 protection, suitable for surface and flush mounting, IN REPLACEMENT, complete all as specified comprising the following: |
| 98 | MCB suitable for 240 volt AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 6 to 32 Amp, complete all as specified. |
| 99 | MCB suitable for 240 volt AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 6-32 Amp complete all as specified. |
| 100 | LED tube lights fitting 1x 20W, 220V AC, 4 ft, decorative box type made of aluminim die cast housing with high out put diffuser,driver,LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, IN REPLACEMENT all as specified and directed. |
| 101 | LED security light 60 watt, outdoor type pressure die cast aluminium housing, heat resistant toughtened glass with frame and lamp with minimum efficiency 110 LM/W, IP 66 protection, IN REPLACEMENT and making connections, complete |
| 102 | Exhaust fan steel body of size 300mm sweep with louvers, 900 RPM 230 volts single phase AC supply complete with bolt, nuts and washer and including PVC insulated and overall sheathed flexible 3 core 0.5 Sq.mm copper conductor cable from ceiling rose to exhaust fan for giving connection complete all as specified. |
| 103 | Supply, laying, jointing & testing of LT XLPE insulated cable screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor conforming to IS-7098 (Part-I -1988) laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing including taking down existing cable (except item no 92.03) , complete all as specified of sectional area: - |
| 104 | 6 Sq.mm, 2 core |
| 105 | 10 Sq.mm, 2 core |
| 106 | 95 Sq.mm,3.5 core |
| 107 | Brick protection with pulverized fuel ash lime bricks laid flat across the route of underground cable all as specified. |
| 108 | Clean dry sand ( locally available) as cushioning for under ground cable 230 mm thick (one layer of 80 mm thickness before laying the cable and other layer of 150 mm thickness after laying the cable) complete all as specified.NOTE:- Punned down thickness (over all 180 mm) shall be considered for measurement and payment. |
| 109 | Change over switch 250 Amps complete all as spececified and as directed Please Enable Macros to View BoQ information |
| 110 | Change over switch 250 Amps complete all as spececified and as directed Please Enable Macros to View BoQ information |
