|
| 1 | Surface dressing n.exc 15 cm deep and getting out in soft/ loose soil complete all as specified and as directed. |
| 2 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and as directed. |
| 3 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 4 | Returning filling in trenches including spreading levelling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified and as directed. |
| 5 | Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and as directed. |
| 6 | M&L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 7 | M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 8 | All as per Ser item No 7.00 (here-in-before) but 5mm dia and over and including 10mm dia in stirrups spacers and binders. |
| 9 | M&L for RCC design Mix M-25 as in foundation, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc basement slabs under reamed piles and mass concrete complete all as specified and as directed. |
| 10 | M&L for RCC design Mix M-25 as in columns, pillars, piers, posts and struts complete all as specified and as directed. |
| 11 | M&L for RCC design Mix M-25 as in beams, cantilvers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 12 | M&L for RCC design Mix M-25 as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 13 | M&L for form work with fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc 200mm thick (horizontal or sloping) complete all as specified and as directed. |
| 14 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 15 | Use and waste of formwork to sides of pillars posts, struts, piers, columns and stanchions finished the suface rough complete all as specified and directed. |
| 16 | Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams complete all as specified and directed. |
| 17 | M&L for brick work with sub class `B' bricks(using old size burnt bricks) straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed. |
| 18 | M&L for brick work with sub class `B' bricks (using old size burnt bricks) straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and as directed |
| 19 | M&L for Brickwork with sub class‘B’ bricks(using old size burnt bricks) in one brick thick honey comb walling, built in CM (1:3) complete all as specified and as directed |
| 20 | Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed |
| 21 | M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface. |
| 22 | M&L 40 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded stone agg) as damp proof course to horizontal or vertical surfaces including necessary form works, applying evenly a coat of blown type bitumen at 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified and as directed. |
| 23 | M&L PCC (1:4:8) type D-2, 75mm thick as in sub base of floor complete all as specified and as directed. |
| 24 | M&L for providing Machine cut ,mirror polished kota stone slab flooring 20-25mm thick over and including 20mm thick screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone floor/steps treads including rubbing and polishing complete all as specified and as directed. |
| 25 | M&L for providing Machine cut ,mirror polished kota stone slab flooring 20-25mm thick over and including 10mm thick baking coat in CM (1:4) on vertical surfaces laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone slab including rubbing and polishing complete all as specified and as directed. |
| 26 | M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed. |
| 27 | M & L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick or concrete work finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 28 | M & L for rendering 15mm thick in cement mortar (1:4) using WPC @ 3% by weight of cement on fair faces of brick or concrete work finishing the surfaces even and smooth without using extra cement complete all as specified and directed.Note: WPC will be measured and paid separately |
| 29 | M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer on wall surfaces complete all as specified and as directed. |
| 30 | M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer of approved shade on walls complete all as specified and as directed. |
| 31 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 32 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 33 | S&F steel work in tubular trusses, post, purlins,rafter including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 complete all as specified and as directed. |
| 34 | S&F Pressed steel frames of size 125 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,with and including filling hollow of frame with PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed. |
| 35 | S&F factory made 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels complete all as specified and as directed. |
| 36 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 37 | S&F sheet glass 3mm thick ordinary quality, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 38 | S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete all as specified and as directed. |
| 39 | S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 40 | M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer on new surfaces in any tint complete all as specified and as directed. |
| 41 | M&L for preparation of untreated new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink wood primer complete all as specified and as directed. |
| 42 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in soft/ loose soil complete all as specified and as directed. |
| 43 | S&F plates (plain or chequered) channels. Square cut or notched ) (ordinary and counter sunk) forming holes, without any attachment, Fe 410-W complete all as specified and as directed. |
| 44 | S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other end to be fitted with washer and one hexagonal or squre nut n exc 15cm long 12mm dia complete all as specified and as directed. |
| 45 | M&L for Rendering 15 mm thick in CM (1:4) on brick work/concrete surfaces other than fair faces finished even and smoth without using extra cement complete all as specified and as directed. |
| 46 | M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid, jointed with grey cement and no pigment laid over and including 50 mm thick sand cushioning and pointed in colour cement mortar (1:3) etc complete all as specified and as directed. |
| 47 | M&L for preparation for newly plastered surfaces and applying two coats of white wash complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 48 | M&L for preparation for newly plastered surfaces and applying two coats of white wash complete all as specified and as directed. Please Enable Macros to View BoQ information |
