|
| 1 | Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m all as Specified and Directed by Engineer Incharge |
| 2 | Filling from available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete |
| 4 | Surface dressing of the ground in all kind of soil including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 5 | Concrete with 4 cm guage approved stone ballast,approved coarse sand and cement in the proportion of 6:3:1 including supply of all materials labour T&P etc required for proper completion of work. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level of grade 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 12 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Up to plinth level of Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 13 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.All works above plinth level upto floor V level of Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 14 | M-150 Brick work in 1:4 cement & coarse sand mortar in foundation & plinth including supply of all material,labour T&P etc required for proper completion of the work |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes with Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level with Cement mortar 1:3 (1 cement :3 coarse sand) |
| 17 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels with Granite stone slab colour black, Cherry/Ruby red for Area of slab upto 0.50 sqm |
| 18 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (For Granite work ) |
| 19 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. |
| 20 | Providing and fixing expansion hold fasteners Wedge expansion type (Fastener with threaded dia 12 mm) on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.Fastner with threaded dia 12mm |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 22 | Providing and fixing ISI marked flush door shutters (35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws) conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35mm thick including ISI marked stainless steel butt hinges with necessary screws. |
| 23 | Extra for Providing and fixing flush doors with decorative veneering On one side only instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) |
| 24 | Providing and fixing M.S. grills (Fixed to steel windows by welding) of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding |
| 25 | Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges (125x65x2.12 mm) bright finished with necessary screws etc. complete |
| 26 | Providing and fixing bright finished brass tower bolts (barrel type of size 250x10 mm) with necessary screws etc. complete : |
| 27 | Providing and fixing bright finished brass handles of size 125 mm with screws etc. complete: |
| 28 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 29 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 30 | Providing and fixing aluminium sliding door bolts of size 300x16 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 31 | Providing and fixing aluminium sliding door bolts of size 250x16 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete. |
| 32 | Steel work welded in built up sections/ framed work, In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cutting, hoisting, fixing in In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 33 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 34 | Kota stone slab flooring of 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand). |
| 35 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 36 | Providing and laying vitrified floor tiles (Size of Tile 600 x 600 mm) thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete |
| 37 | Providing and laying Polished Granite stone flooring slab of colour Black, Cherry/Ruby Red or equivalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 38 | Providing and fixing rain water spout (Stoneware spout) 100 mm diameter and 60 cm long in cement mortar 1:4 (1 cement : 4 fine sand). |
| 39 | 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) |
| 40 | 15 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) |
| 41 | Distempering with 1st quality acrylic distemper (readymixed) having VOC content less than 50gram per ltr of approved manufacturer & of required shade and colour all complete to achive even shade and colour.New work (Two or more coats) over and including water thinable priming coat with cement priming having VOC content less than 50 gram/litre |
| 42 | Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm |
| 43 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approvedbrand and manufacture |
| 44 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade with Two or more coats on new work |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 46 | Providing & fixing White vitreous china water closet squatting pan (Indian type) Orissa pattern W.C Pan of size 580x440 mm along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
| 47 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- of Hindware,Parryware make only. |
| 49 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board 510x1040 mm bowl depth 250mm. as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required of approved quality: |
| 50 | Providing and fixing mirror of superior glass (of approved quality) and of Rectangular shape 1500 x 450 mm with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. |
| 51 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 15 mm nominal dia Pipes , having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 52 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 20 mm nominal dia Pipes , having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 53 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 25 mm nominal dia Pipes , having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 54 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 15 mm nominal dia Pipes , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 55 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 20 mm nominal dia Pipes , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 25 mm nominal dia Pipes , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 57 | Providing and fixing C.P. brass long body bib cock of 15mm nominal bore of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 58 | Providing and fixing C.P. brass stop cock (concealed) of 15 mm nominal bore of standard design and of approved make conforming to IS:8931. . |
| 59 | Providing and fixing C.P. brass angle valve of 15mm nominal bore for basin mixer and geyser points of approved quality conforming to IS:8931 . |
| 60 | Providing and fixing PTMT grating of approved quality and colour. (Circular type of 100 mm dia ) |
| 61 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. |
| 62 | Providing and fixing square-mouth S.W. gully trap class SP-1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: |
| 63 | Providing and fixing aluminium ( Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)) work For fixed portion for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required ncluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 64 | Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). - |
| 65 | Providing and fixing glazing ( With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) ) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item). |
| 66 | 40 mm thick 1:1.5:3 CC floor with cement approved coarse sand & 20mm graded approved stone grit laid in pannels finished with 3mm floating coat of neat cement or cement & marble dust in 5:1 as specified over & including removing any over lapping mortar at the joints of pannels if any and given them a uniform finish i/c supply of all material labour & T&p etc required for proper completion of the work.(As per item no.605) |
| 67 | Providing Aluminium curtain rod 20mm dia |
| 68 | Providing curtain rod bracket for 20mm dia |
| 69 | Providing anti termite treatment oil |
| 70 | Mild steel or iron work in heavy sizes such as trusses,built up gates,record racks,roof work,gates etc wrought to required from i/c drilling holes riveting or welding where necessary & their fixing required for proper completion of the work |
| 71 | Providing & fixing box type fan hook (minimum 10cm dia i/c fixing |
| 72 | Providing & fixing on wall face unplasticised rigid PVC rain water pipes confirming to IS:13592 Type A,including jointing with seal ring confirming to IS:5382,leaving 10 mm gap for thermal expansion (i) single socketed pipe of 110 mm diameter. |
| 73 | Wiring for light point/fan point/exhasut fan point/call bell point with 1.5sqm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch modular plate,suitable GI box and earthing the point with 1.5sqm FRI.S PVC insulated copper conductor single core cable etc as requried Group C. |
| 74 | Wiring for twin control light point with 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit the point with 1.5sqmm FRLS PVC insulated copper conductor single core cable etc.as required. |
| 75 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in in recess, including providing and fixing 3pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc as required . |
| 76 | Supplying & fixing suitable size GI box with modular plate & cover in front on surface or in recess, including providing and fixing 6pin 5/6A & 15/16A A modular socket outlet and 15/16 a modular switch, connections etc as required. |
| 77 | S/f DP Sheet steel enclouser on surface/recess along with 25/32A 240V \\"C\\" curve DP MCB complete with connections, testing and commissioning etc as required |
| 78 | Cell bell/buzzer,single phase. |
| 79 | S/F of LED T/L 1x22watt(AR) |
| 80 | S&F of 100Amp.four pole change over switch on 40mmx40mmx6mm angle iron frame, including the cost of labour, T&P, Painting & other material requried for proper completion of the work as per direction and satisfaction of engineer-in-charge Q/R |
| 81 | S/F of Mirror Light,AR |
| 82 | S/F of Making whole in wall for Exhaust-fan with fixing of MS drum complete,AR |
| 83 | S/F of 7 to10 watt LED,QR |
| 84 | S/F of 63A/4Pole MCB,QR |
| 85 | S/o Invertor wiring point for Light/Fan/Plugh with 1.5mm copper wire |
| 86 | S/F two module stepped type electronic fan regulator on the existing moduler plate switch box including connection but excluding modular plate etc as required. |
| 87 | 4 Way, (4+12) TPN, prewired MCB DB with extended loose wire box double door |
| 88 | 6 Way, (4+18) TPN, prewired MCB DB with extended loose wire box double door |
| 89 | 8 Way, (4+24) TPN, preview MCB DB with extended loose wire box double door |
| 90 | Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required, 2x2.5sqmm+1x2.5sqmm earth wire |
| 91 | Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required, 2x4sqmm+1x4sqmm earth wire |
| 92 | Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required, 2x6sqmm+1x6sqmm earth wire |
| 93 | Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required, 2x10sqmm+1x6sqmm earth wire. |
| 94 | S/F of Hexagonal/Round Fan Box |
| 95 | S/F of surface/pendent mounting round 6watt to 8watt LED complete in all respect AR |
| 96 | Earthing with G.I earth plate 600mmx600mmx6mm thick including accessories and providing masonry enclouser with cover plate having locking arrangment and watering pipe of 2.7metre logn ect.(but without charcoal/coke and salt) as required |
| 97 | S/I 25mmx5mm G.I sprit at 0.50metre below ground as strip earth electorde, including connection/terminating with I.G nut, bolt, spring, washer etc. as requried (Jointing shall be done by overlapping and with 2 sets of G.I nut bolt & spring washer spaced at 50mm) |
| 98 | S/I of AI conductor PVC 400sqmm 3 1/2 Core |
| 99 | S/I of AI conductor PVC 50sqmm 3 1/2 Core |
| 100 | Brass compression gland for (82mm) 31/2 x 400 sqmm1.1 KV grand cable |
| 101 | Brass compression gland for (35mm) 31/2 x 400 sqmm 1.1KV grand cable |
| 102 | Aluminium lugs for 400 sqmm cable |
| 103 | Aluminium lugs for 50 sqmm cable |
| 104 | Aluminium lugs for 35 sqmm cable |
| 105 | Aluminium lugs for 25 sqmm cable |
| 106 | S/F of water tight bulkhead 10watt LED complete in all respect,AR |
| 107 | Errection & Testing charges of ceilling Fan&Regular etc |
| 108 | Errection & Testing charges of EX-Fan etc,QR |
| 109 | Cost of 300mm Exhaust Fan Crompton/Bajaj/Havells make only |
| 110 | S/F of 32 AMP 4 pole MCB.QR |
| 111 | S/F of 63 AMP 4 pole MCB.QR |
| 112 | S/F of 80 to 100 AMP 4 pole MCCB.(16KA) Thermal Magenctic release, QR |
| 113 | 6A to 32A,ratings,DP MCB \\"C\\" curve, 10KA breaking capacity |
| 114 | 6A to 32A,ratings,SPN MCB \\"C\\" curve, 10KA breaking capacity |
| 115 | 200 A TPN compact type rising mains with aluminium bus bar including all accessories. |
| 116 | G.S.T. @ 18% Please Enable Macros to View BoQ information |
