|
| 1 | Hire charges for supplying and fixing of weldmesh partition using with 3\\"x1\\", 10 gauge weld mesh for partition panel, the outer frame and diagnoal members are using country wood reeper of size 2\\"x1\\"including cost of materials, labour charges, fixing charges and removing the same after the work completed etc., complete complying with standard spcification and as directed by the departmental officer. |
| 2 | Using new weld mesh |
| 3 | Using old weld mesh |
| 4 | Hire charges for providing supporting arrangements for Inner barricading segregate the path way using 10 to 13cm dia casurina post for vertical at an interval of 3m c/c upto roof height including diagonal and horizontal bracings of 5 to 8 cm dia casuina post and tying with coir, nails etc including labour charges for removing the same after the work completed etc., complete complying with standard spcification and as directed by the departmental officer. |
| 5 | Hire charges for providing inner barrigading arrangements for using casurina props 8cm to 10cm from floor level to roof level at 3m centre to centre and 5 to 8 cm dia Casurina probs for horizontal in 3 tires and the lowest should be 45cm above floor level and tied with new coir rops provided in all places and removing the same after the work completed. Lateral support with cross bracing shall also be provided with 8 to 10cm dia casurina poles at 3m interval and removing the same after the work is completed etc., complete complying with standard specification and as directed by the departmental officer. |
| 6 | Hire charges for supplying and fixing of Termite Proof / Water proof 19mm thick plywood for closing windows and doors including fixing with 2\\"x1\\"country wood reaper frame on both sides including cost and labour and fixing charges at site and removing the same after the work is completed etc complete complying with standard specification and as directed by the departmental officer. |
| 7 | Dismantling and clearing away and carefully stacking materials useful for reuse of brick masonry wall in cement mortar upto 3m height etc, complete complying as with standard specification and as directed by the departmental officer. |
| 8 | Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9\\" x 4 3/8\\" x 2 3/4\\" with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) |
| 9 | Ground floor 11.50 cm thick. |
| 10 | In First Floor 11.50 cm thick. |
| 11 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 12 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used, hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers. |
| 13 | Paving the floor with best quality Double charged vitrified Tiles of size 600 x 600 x 8mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 14 | Distempering the old wall and ceiling two coat with best oil bound distember of approved quality including preparation of surface, the rate includes cost of brushes, high scaffolding arrangements, neat finishes, etc., complete complying with standard specification and as directed by the departmental officers. |
| 15 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 16 | Supplying and fixing of 4'40 W twin mirror optic recessed mounting type fitting complete with copper chokes and condensor with louvers cover on wall or ceiling with PVC unsheathed leads from terminals to the fitting with fluorescent tubes. (SD 97) |
| 17 | Charges for removing of glass writing board in class room during dismantling of wall and refixing of the same board after constructed wall after the counting process including of teak wood plug and screws etc., complete complying with standard specification and as directed by the departmental officers. |
| 18 | Engaging labour for transporting the desks, benches, tables, library racks and other materials from the existing class rooms to the college store rooms / workshops and to a distance of 300 - 400 m from the counting centers / storage halls and refixing the same in the previous location after the counting etc., after attending to the repair works complete complying with standard speciations and as directed by the departmental officers (as per quotation rate) |
| 19 | Carpenter I Class |
| 20 | Mazdoor I Class |
| 21 | Mazdoor II Class |
| 22 | Renewal and fixing in position pin headed glass of thickness 4mm, etc complete complying with standard speciations and as directed by the departmental officer. |
| 23 | Painting Old wood work with Two coat of synthetic enamel ready mixed paint of approved quality and colour in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 24 | Old Terrace Screed Repair with UV Resistant Hybrid PU Waterproof coating above 500 Sq.m- Providing and Applying high perfomance solar reflective & Acrylate silicon based Waterproofing coating which is single component, cold applied, water based acrylic and UV resistant water proofing treatment to the Existing Roof screed surface applied @ 1.5 l/m2 in 3 coats to achieve 1mm DFT, having tensile strength 2N/ mm2 confirming to ASTM D 412; Elongation at break ≥ 200%, Abrasion resistance 21mg confirming to ASTM D 4060 and Crack bridging ability up to 2 mm, including surface preparation, priming the surface with 1 coat diluted with water in the ratio 2:1 spreading @ 0.125 L/m2 as self-priming coat in the SSD condition and spreading 45 gsm glass fibre mesh of 2.5 mm x 2.5 mm sandwiched between the first and second coat completely as per specification. The finished cost to include surface preparation, making coving at Junction, treatment of cracks completely as per specification. |
| 25 | Hire Charges for providing GI Sheet enclosure using GI Sheet 18 gauge/0.80mm thick of approved quality including fixing with necessary country wood reeper frame of size 50x25mm and wrought and put up and removing the same after the work is completed etc complete complying with standard specification and as directed by the departmental officer. |
| 26 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m, Centre mullions: 63.50x38x3mm@ 1.55 kg/m, Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column, masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use. |
| 27 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the deparmental officers. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. |
| 28 | Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 29 | Finishing the top of roof with one course of machine pressed tiles of size 230x230x20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. |
| 30 | Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by mechanical means |
| 31 | Supplying, fabricating and fixing in position of steel frame without bottom frame, of size 100X60mm rectangular section with necessary rebate 30mmX15mm, to host the shutter,using 1.25mm thick (18 guage) CRCA cold rolled frame steel plate confirming to ISI specified ensured of right butt joint riveted hold assembly with nylon insert,not be welded with special purpose hard ware.Proclaimed including phopating as per ISI with rust preventive primer ready to assemble condition for easy installation at site including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc... complete complying with standard specification and as directed by the departmental officers. |
| 32 | Supplying and fixing solid core flush shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 3 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm) , 2 Nos 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.Type : Solid Core Flush Shutters with teakply on both side withteakwook lipping alroundThickness: 35mm thick |
| 33 | Supplying and fixing of Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter etc complete complying with standard specification. |
| 34 | Painting Old Plastered Wall Surface with Two finishing coats of ready mixed Exterior (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 35 | Supplying, fabricating, erecting and fixing Calcium Silicate Board False Ceiling upto a ceiling height of 4.5m from floor level-Using Calcium Silicate Board Plain Sheets (10mm thick) |
| 36 | Manufacturing supplying and fixing of Fully panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 4nos. One the top of each shutter, one at lock rail and the other at the bottom are provided. 1no. Aldrop is provided at lock rail section in the door 3 Nos of handle are to be provided, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers. - Double leaf of size 1.20m x 2.10m. |
| 37 | Brick work in Cement Mortar 1:5 (One Cement and five Crushed stone sand) using best quality Burnt Clay Brick of size 9\\" x 4 3/8\\" x 2 3/4\\" with class designation of 7.5 conforming to IS 1077-1992 including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally other type of bond shall be done as directed by the Executive Engineer in charge. |
| 38 | For foundation and basement |
| 39 | In Ground floor |
| 40 | In First floor |
| 41 | Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)-15mm dia CP Screw Down Tap |
| 42 | Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. |
| 43 | Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct- ed by the departmental officers. |
| 44 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. - Mixing by manual means |
| 45 | Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers. |
| 46 | Supplying and fixing in position 15mm die PVC tap approved make conforming to BIS specifications and quality including cost of shellac, etc., including cutting and threading wherever necessary etc. Complete complying with standard specification. (Taps should be got approved by the Executive Engineer before use on the works) |
| 47 | Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
| 48 | Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). |
| 49 | Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) |
| 50 | Supplying and fixing in position Health faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works). |
| 51 | Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., includ- ing dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.) |
| 52 | Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) |
| 53 | Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - Internal water supply above ground level. |
| 54 | 20mm dia UPVC pipe |
| 55 | 25mm dia UPVC pipe |
| 56 | 32mm dia UPVC pipe |
| 57 | 40mm dia UPVC pipe |
| 58 | Supplying, laying and jointing 32mm dia UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety conforming to BIS of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level |
| 59 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 60 | 32 mm dia G.M. Gate Valve |
| 61 | 40 mm dia G.M. Gate Valve |
| 62 | Supplying and fixing in position best quality 110mm dia PVC soil / waste pipes having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level |
| 63 | Supplying and fixing in position 110mm dia PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re- doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 64 | PVC Elbow |
| 65 | PVC Elbow with door |
| 66 | PVC Tee |
| 67 | Hire Charges for G.I. Sheet 18 gauge/0.80mm thick for toilet partition wall upto 2.10m height using casurina props 8-10cm for horizontal and vertical support and door arrangements including cost of conveyance and labour charges and removing the same after the work is completed etc complete complying with standard spcification and as directed by the departmental officer. |
| 68 | Supplying and fixing in position best quality 25mm Nylon hose using of distributing the water to the centralized sump in GPT campus etc., complete complying with standard specifications. (hose should be got approved by the Executive Engineer before use on the works) |
| 69 | Supplying of plastic bucket and mug for toilet usage including cost of conveyance charges etc., complete and as directed by the departmental officers. (Plastic bucket and mug should be got approved by the Executive Engineer before use on the works) -5 liter capacity bucket with mug |
| 70 | Supplying, fixing of cylindrical vertical notational polythene water storage tank of 1000 litres capacity confirming to I S. 12701 / 96. the tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simply pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank etc., and the tank should be fixed firmly as directed. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., |
| 71 | Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers. |
| 72 | Charges for cleaning the septic tank by pumpimg with power pumping motor and unload the sludge to out side the campus including conveyance and labour charges and for pumping etc. complete complying with standard specifications and as directed by the departmental officers. |
| 73 | Hire charges for providing outer barrigading arrangements for using in casurina props 8cm to 10cm and 60cm below ground level and 1.20m above ground level fixing 3 horizontal in 3 tires and the lowest should be 45cm above ground level and tied with new coir rops provided in all places and removing the same after the work is completed etc complete complying with standard specification and as directed by the departmental officer. |
| 74 | Hire Charges for providing outer barricading arrangements using Metal barricading units of size 10'x4' made up of Steel Pipes of dia not less than 50 mm dia removing the same after the work is completed as per standard specification and as direction of the departmental officers etc., Complete. |
| 75 | Hire charges for providing Movable barricade of size 3m length 1.20m height using 8 to 10 cm dia casurina props for vertical member & Horizontal Member , 5 to 8 cm dia for horizontal and diagonal member including cost and labour and removing the same after the work is completed etc complete complying with standard specification and as directed by the departmental officer. |
| 76 | Hire charges for providing checking booth of size 1.50mx1.50m and height of 2.10m using 8 to 10 cm dia casurina props for vertical member and 5 to 8 cm dia for horizontal and diagonal member and using white cloth for covering four sides including cost and labour and removing the same after the work is completed etc complete complying with standard specification and as directed by the departmental officer. |
| 77 | Hire Charge for providing Police Tower booth of size 1.20mx1.20m and height of 3m with Casuina poles ladder arrangemnts using 8-10 cm dia Casuina poles for Horizontal props for and 10 to 13 cm dia casuina poles for Vertical member including cost and labour charges and removing the same after the work is completed etc complete complying with standard spcification and as directed by the departmental officer. |
| 78 | Hire Charges for Earth work Open excavation for approach road clearing Jungle, using JCB machineries etc., Complete complying with standard specification and as directed by the departmental officers. |
| 79 | Hire Charges for providing agent waiting shed for the suitable sizes using MS pipe for vertical support and MS box section for purlin assembling with bolt and nuts, top roof covered with G.I. sheet 18 gauge / 0.80mm thick and 3 sides of the waiting shed covered with G.I. sheet of approved quality and inner portion of the shed vertical wall finished with cotton cloth for the purpose of control heat radiation and necessary wooden platform top finished with matt flooring for the sitting purpose, watching and monitoring CCTV camera connected from the storage room in 24 Hour and removing the same after the work is completed etc complete complying with standard spcification and as directed by the departmental officer. |
| 80 | Hire charges for Plastic chairs with arms including cost of conveyance charges etc., complete complying with standard specification and as directed by the departmental officers. |
| 81 | Hire Charges for SS Dinning Table of size (6' x 1 1/2' x 2 1/2\\") including cost of Conveyance charges etc., complete complying with standard specification and as directed by the departmental officers. |
| 82 | Hire charges for supplying of Cushion sofa Set (3 seater 1 no, single seater 2 no's) with resin cloth and wooden hand rest with wood finishing including cost of transporting charge etc., complete compling with standard specification and as directed by the departmental officers. |
| 83 | Supplying and fixing 12mm thick Ply wood for closing the window, ventilator opening with wooden frame including cost of country wood reeper of size 50mm x 25mm, 12mm thick ply wood sheet, nails, conveyance charges and as directed by the departmental officers. |
| 84 | GST Please Enable Macros to View BoQ information |
