|
| 1 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts. Leveling ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I. Extra for earthwork in hard soil as per specification and direction of E/I. (vide classification of soil item |
| 2 | Filling in foundation trenches and plinth in layers not exceeding 150mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume) |
| 3 | Providing coarse clean sand in filling in foundation trenches or in plinth & floor including ramming & watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume). |
| 4 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I. |
| 5 | Providing and laying in position cement concrete of specified grade |excluding the cost of centering and shutfering All work up to plinth level:1:2:4 (1 cement: 2 coarse sand (zone-1) :4 graded stone aggregate 20 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade |excluding the cost of centering and shutfering All work up to plinth level:1:3:6 (1 Cement: 3coarse sandzone-ll):6 graded stone aggregate 20 |
| 7 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9'x4.5\\"x3\\") in C.M. ( 1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials,raking out joints to 15mm Depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 8 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 9 | Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I. |
| 10 | Providing designation 75A brick work in C.M (1:4) in foundation and plinth -do- |
| 11 | Providing and laying in positionspecified grade of reinforaed cement concrete, excluding the cost of centering, shutterhe. finishing and reinforcement- All work upto plinth level. 1.5:3 (1 cement: 1.5 course sand (zone-1): 3 graded stone geregate 20 mm nominal size) |
| 12 | Reinforded cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:15:3 cement: 1.5 coarsesand(zone-l):3 graded stone aggregate 20 mm nominal size). |
| 13 | Reinforced cement concrete work in wals (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets column pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering& finishing and reinforcement : 1:1.5:3 cement: 1.5 coarse sand (zone-l):3 graded stone aggregate 20 mmnominalsize) |
| 14 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand(zone-l):4 graded stone aggregate 20mm nominal size). |
| 15 | Centring and shuttering including strutting, propping etc. and removal of form for foundation, footings, bases of columns etc. for massconcrete. |
| 16 | Centring and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, postsand struts |
| 17 | Centring and shuttering including strutting, propping etc. and removal of form for lintel, beams, plinth beams, griders, bressumers andcontilevers. |
| 18 | Centring and shuttering including strutting, propping etc. and removalof form for suspended floors, roofs, landings, balconies and access platform. |
| 19 | Reinforcement for RCC work including straightening, cutting, bending, placing in position and bonding all complete. TMTC-500 8mm dia |
| 20 | TMTC-500 10mm dia |
| 21 | TMTC-500 12mm dia |
| 22 | TMT-500 16mm dia |
| 23 | Supplying, fitting and fixing fully glazed steel door, windows or ventilators of standard Z and mullion steel sections and size as per IS 1038 joints met and welded with 100x16x3mm M.S Lugs fixed in cement concrete 1:2:4 blocks 15x10x10 cm size including cost of oxidized iron fittings with hinges handle per steps catch springs 3mm thick plain glass panes with aluminium beads and inner frame fixed with lugs with 20mm long 6.3mm G.I counters sunk machine screw and nuts and applying a coat of red lead paint, carriage to work site, hosting & placing in position in all stories and taxes all complete as per building specification and direction of E/I. |
| 24 | Supplying.fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20X10X2 mm. at 100mm. Centres and braced with M.S. flat diagonals 20 X 3mm with top ad botom rails of T. iron 40x40x6mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification |
| 25 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 26 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I |
| 27 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames einforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-chargeExtruded section profile size 48x40 mm |
| 28 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (±0.2 mm) with inbuilt edging on both sides. The styles and rails mitredand joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filledwith a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 29 | S/F/F good quality wall dressed and well seasoned local wood work in chaukhat in doors, window skylights, fanlights and C/W celestial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I. |
| 30 | Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 31 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 32 | Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar (1:4) (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc, complete - size of tiles 600X600mm |
| 33 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete |
| 34 | Providing and laying CProviding and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.eramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete |
| 35 | Providing 12 mm , cement plaster (1:6)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water,scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 36 | Providing 12 mm , cement plaster (1:6)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water,scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 37 | Providing 6mm thk.cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per builingspecification and direction of E/I. |
| 38 | Providing 19 mm , cement plaster (1:3)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water,scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 39 | Providing and applying WHITE cement based putty 1 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 40 | Painting wWall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.ood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufactureTwo coats |
| 41 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat [email protected]/10sqm over and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 42 | Providing and laying 25mm. thick kotah stone tiles in risers of steps, skiiting and pillars of approves size, texture and colour laid cover 12mrn. thick cement mortar (1:3) and.loined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolilthic finish with approved quality of carborandurn stone including cost of curing, taxes and royaliy all complete as per building specificationand direction of El. |
| 43 | Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 44 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 45 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixed a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580 mm. long With 10 lit. low level P.V.C Cistem |
| 46 | Supplying, fitting and fixing 40mm high vitreous white glazed ware E.W.C. with \\"p\\" trap of parry/hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make and complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle cock of approved qualty weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and White/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide prining, all complete as per specification and direction of E/I. With s trap 10 lit. low level P.V.C cistern |
| 47 | Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 48 | Supplying fitting and fixing white glazed fire's clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P. brass waste with C.P. brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I Kitchen sink 600 mm x 450 mm x 250 mm |
| 49 | Supplying, fitting and fixing H.C.I. pipes with ear of approved make conforming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yarn for making lead caulked joints, cutting pipes to size including earth woek or scaffolding where necessary etc. all complete as per specification and direction of E/I. 100mm dia |
| 50 | 75mm dia |
| 51 | Supplying and fixing H.C.I. fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earthwork or providing scaffolding as the case may be all complete as per specification and direction of E/I. H.C.I. Heal Rest bend 100 mm dia (wt. 5.5 kg. app) |
| 52 | 80 mm dia (wt. 4 kg. app) |
| 53 | H.C.I. double junction with door and ear 100 mm dia (wt. 15.5 kg. app) |
| 54 | 80 mm dia (wt. 15.5 kg. app) |
| 55 | Floor trap with grating 100mm dia |
| 56 | Norton patent H.C.I. Cowel 100mm dia (wt. 3.25 Kg appx.) |
| 57 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 110 mm diameter |
| 58 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 59 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single pushfit Coupler110 mm |
| 60 | Single tee with door 110x110x110 mm |
| 61 | Bend 87.5° 110 mm bend |
| 62 | Shoe (Plain) 110 mm Shoe |
| 63 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 64 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 65 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 15 mm dia |
| 66 | 20 mm dia |
| 67 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.25 mm nominal outer dia Pipes |
| 68 | 32 mm nominal outer dia Pipes |
| 69 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe |
| 70 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore |
| 71 | 25 mm nominal bore |
| 72 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 73 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 74 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 75 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line |
| 76 | Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. Group C |
| 77 | Twin control Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for twin control light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2 way modular type switch, modular plate, suitable size of GI box etc as required. |
| 78 | S/F Ceiling Rose :-Supplying and fixing 2pin 5 amp ceiling rose on the existing junction box/wooden block including connection as required etc. |
| 79 | S/F Modular type electronic fan regulator :- Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required. |
| 80 | Supply, fitting, fixing and testing of 1200mm Sweep, double ball-bearing, 2 canopy ceiling fan including connection with 1.5 sq mm copper wire, down rod all accessories as required. |
| 81 | S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. compete as required.20w/22w LED tube |
| 82 | Bulk head fitting with 9/10 Watt LED |
| 83 | S.I.T.C of following rating LED post top lamp made in die cast aluminium housing with decorative claer/opal acrylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required. 45w LED Post top lamp opel |
| 84 | 12\\" (300mm) Exhaust fan |
| 85 | Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of he above fan making good the damage, connection, testing, commisionig etc as required. S/F light plug point with modular type accessories :- |
| 86 | Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required. |
| 87 | S/F light plug point with modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 88 | S/F 20amps SPN MCB industrial Socket:- Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps \\"C\\" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc. |
| 89 | S/F Modular boxes, base & cover plate :-Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required. 4/5 module (78mm x 140mm x 50mm) |
| 90 | 8 module (78mm x 230mm x 60mm) |
| 91 | S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required. |
| 92 | Supplying and fixing following way three pole & neutral ,sheet steel, MCB distribution board, 415 volts, onsurface /recess, complete with tinned copper bus bar, neutral bus-bar, earthbar ,dinbar, interconnections, powder painted including earthing etc. as required. 4 Way (4 + 12), Double Door, Horizontal type |
| 93 | SUBMAIN WIRING COPPER IN PVC CONDUIT Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor single core cable in surfacce/ recessed medium class PVC conduit. |
| 94 | 4R X 10 sq. mm + 2R x 6 sq.mm Earth Wire |
| 95 | CIRCUIT WIRING COPPER IN PVC CONDUIT FOR 5A & SWICTH BOARD:- Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor single core cable in surfacce/ recessed medium class PVC conduit. 2R X 4 sq. mm + 1R x 4 sq.mm Earth Wire (Sockets) |
| 96 | 2R X 2.5 sq. mm + 1R x 2.5 sq.mm Earth Wire (Switch Boards) |
| 97 | 2R X 1.5 sq. mm + 1R x 1.5 sq.mm Earth Wire (Switch Boards) |
| 98 | Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required. 3.5c x 95 sq.mm |
| 99 | Supplying all materials, labours and tools and equipment for drilling 200x150 x125mm dia bore well in any kind of soil and rock by using DTH Super Rig machine and ball hammer technology inclusive of mobilization, demobilization, demobilization of rigs air compressor all accessories of rigs tool and plant labour etc. all complete job including transportation charge.(a) 0.00 to 50.00 M below G.L. |
| 100 | (a) 50.00 to 125.00 M below G.L. |
| 101 | (b) 125.00 M above G.L. |
| 102 | Gravel Packing in tube well construction in accordance with IS:4097 including providing gravel fine/medium/coarse in rquired grading & size as per actual reqirement all complete as per direction of E/I |
| 103 | Supplying, assembling, lowering and fixing in vertical position in bore well, un-plasticized PVC medium well casing (CM) pipe of required dia, all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia. |
| 104 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, all as per requirement and direction of Engineer-incharge. |
| 105 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe,Nremovable as per requirement, all complete for borewell of 150Nmm dia. |
| 106 | Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts required size complete.150 mm clamp. |
| 107 | Supplying fitting and fixing of KSB/KIRLOSKER/CRI make 1.00/1.5HP Submersible pump set having head of 135 metre including all taxes, royalty, etc.all complete job as per direction of E/I. |
| 108 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pioes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting this includes jointing of pipes & fitting with one step CPVC solvent cement trenching refilling & testling of jionts complete as per direction of E/I 50 mm nominal outer dia |
| 109 | STONE CHIPS |
| 110 | CEMENT |
| 111 | STEEL |
| 112 | BRICKS |
| 113 | Add GST @ 18% |
| 114 | Add L.Cess @ 1% Please Enable Macros to View BoQ information |
