|
| 1 | Demolition of cement concrte (un- reinforced) in ground floor and paving n. exc 15 cm thick bleow or above hround level complete all as specified and directed. |
| 2 | Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified and directed. |
| 3 | M&L for brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified and directed. |
| 4 | M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/Sqcm) complete all as specified and directed. |
| 5 | M&L for stone walling of random rubble stone masonary, uncoursed, well bounded, bedded & solidely hearted built in cement mortar (1:6) using locally available best stone complete all as specified and directed |
| 6 | Taking down cement plaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc., complete all as specified and directed. |
| 7 | M&L for rendering 10mm thick on stone masonry/brick surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement complete all as specified and directed. |
| 8 | M&L for rendering 15mm thick CM 1:4 on fair face of brick ,hollow block,concrete surface finished even and fair without using extra cement complete all as specified and directed. Note: WPC Shall be measured and paid separately. |
| 9 | Supply only water proofing compouond all as specified as manafature instruction, complete all as specified and directed. |
| 10 | M&L Preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion paint & over one coat of primer complete all as specified and directed. |
| 11 | M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 2mm thick wallcare putty, complete all as specified and directed. |
| 12 | Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 13 | M&L for PCC 25mm thick, type B-0 (using 12.5 mm graded crushed stone agg) as in floor lavelling course complete all as specified and directed. |
| 14 | M&L for coloured glazed ceramic tiles (300x450x7mm thick) in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:4 complete all as specified and directed. |
| 15 | M&L for non skid ceramic tiles 7-8mm thick coloured (Square/ rectangular) each tiles exceeding 0.18 sqm but n exc 0.38 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed as in CM 1:6 , complete all as specified and directed. |
| 16 | M&L for non skid ceramic tiles 7-8mm thick coloured (Square/ rectangular) each tiles exceeding 0.18 sqm but n exc 0.38 sqm in vertical surface such as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cment mortar 1:4 complete all as specified and directed. |
| 17 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar, complete all as specified and directed. |
| 18 | S&F 5 to 8mm thick plain colour PVC sheet hollow interlocking wall panelling of width 250 mm for wall panelling inclusive of fixing on wall with screws and solvent alongwith PVC 'U' and 'L' beading at corner and end portion where ever required of matching colour including taking down of existing wall lining, board or insulation board/panelling including cover fillets of any type and thick complete all as specified and directed.Note : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc. |
| 19 | M&L for Green /Black marble flooring or on cooking platform 18 to 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) ( size of the slabs shalll not be less than 100cmx60cm), complete all as specified and directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achieve the desired granite finish. |
| 20 | M&L for pre-polished lacquer finish chequered cement concrete tiles 300x300x 20-25mm thick, with grey cement and pigment set, jointed and pointed in neat cement slurry in floors over Screed bed or bedding layer of mortar as in 1:6 15 mm thick for laying floor finishes complete all as specified and directed. |
| 21 | Dismantling of RCC shelf other than ground floors and similar suspended works complete all as specified and directed. |
| 22 | M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves/ slabs and like with and incl use and waste of necessary form work complete all as specified and directed. |
| 23 | M&L for MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work, complete all as specified and directed. |
| 25 | Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm complete all as specified and directed. |
| 26 | All as per Srl item No 25 above but for n.exc 1.5 sqm, complete all as specified and directed. |
| 27 | Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and removing to or from store as required complete all as specified and directed. |
| 28 | S&F 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. |
| 29 | S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size MS hinges, lock strike plate, etc., complete all as specified and directed. |
| 30 | S&F of factory fabricated flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 31 | S&F 2nd class (hollock) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed. |
| 32 | S&F in repairs factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge and making it good to match with existing surface, complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 33 | S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 34 | S&F of steel window box type, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skelton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 of HQ CE Chandigarh Zone as applicable including PCC (C-O ,1:3:6 using 12.5 graded stone aggregate) bed blocks for hold fasts including taking down existing window any type complete all as specified and directed.Note: (i) For the purpose of measurement & payment double shutter both glazed and gauzed with frame shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawings and one shop coat of red oxide primer . The pattern of grill shall be all as shown on drawing.(iii) Glazing, wire mesh and painting shall be measured and paid for separately. |
| 35 | S&F box type steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed. |
| 36 | S&F box type steel ventilators, with top hung shutter including hinges steel peg stay, complete all as specified and directed. |
| 37 | S&F sheet glass ordinary quality 4 mm thick glazing in square/ rectangle n.exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel and wooden of any height including necessary scaffolding and T&P required to complete the work complete all as specified and directed. |
| 38 | S&F sheet glass 4.00 mm thick figured glass pin headed type and glazing with oil putty or wooded bead built in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 39 | Dismantling plain or corrugated steel sheeting, with ridge, gutters, etc, any gauge, and thickness incl Nainital pattern roof covering, fixed with J/L hooks or coach screws complete all as specified and directed. |
| 40 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws as complete all as specified and directed. |
| 41 | S&F for pre-painted galvaltume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,facia, ridges ,flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws as complete all as specified and directed. |
| 42 | S&F of PVC false ceiling consisting of 600 mm x 600 mm, 5mm (+ 0.25) thick plain embossed PVC sheet of density 600 Kg/Cbm manufactured by an ISO-9001-2015 certified company, used as panel insert in a frame work made using anodised aluminium T-section of sizes 1\\" x 1\\" (25 mm x 25 mm, 1 mm thick) in square pattern of grid sizes of 2' x 2' (600 mm x 600 mm). The aluminium framework is supported from the ceiling with the help of 'J' hook and G.I. wire of required sizes to maintain proper level etc. The aluminium frame work is supported on the side wall with the use of aliminium L- Section of size 1\\"X1\\" (25mmX25mm, 1mm thick) Angles etc. complete as per direction of Engineer - In- Charge, Manufacturer's specification and drawing including taking down existing ceiling boards (fibre, pulp, insulation etc) or insulation boards/slab etc ant thickness including cover fillets of any description complete all as specified and directed. Note: - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc. |
| 43 | S&F 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame, incl necessaary beading wk where as required etc., including taking down existing boards of any description, complete all as specified and directed. |
| 44 | S&F 0.9mm thick decorative laminate(mica) type 1 of surface finish, colour and pattern as approved and fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed. |
| 45 | S&F in repair floor door stoppers 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floorscomplete all as specified and directed. |
| 46 | S&F galvanized mild steel wire cloth 0.56mm fixed nominal dai of wire and avrg widh of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple, complete all as specified and directed. |
| 47 | M&L for 75mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work, complete all as specified and directed. |
| 48 | S&F Mild steel butt hinges medium weight, clod rolled, 100mm, ISI marked, complete all as specified and directed. |
| 49 | S & F barrel tower bolts aluminium anodised exlruded section of size 200 mm, complete all as specified and directed. |
| 50 | S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts, fixed on plate or staple plate complete all as specified and directed. |
| 51 | S&F aluminium fabricated type extruded handles of size 125 mm complete all as specified and directed. |
| 52 | S&F in repair of 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate complete all as specified and directed. |
| 53 | S&F in repair of aluminium pre coated of choice colour designed type 25 mm tubular rod in curtain rod, 1.6mm fancy type including PVC golden colour brakets/wall to wall socket, two latto for each rod lenth at both end etc., complete all as specified and directed. |
| 54 | Taking up or down 15mm dia steel tubing incl connection and removal from site, complete all as specified and directed. |
| 55 | Taking up or down 20mm dia steel tubing incl connection and removal from site, complete all as specified and directed. |
| 56 | S&F GI tubing medium gde with all fittings fixed to walls or laid in floors 15mm bore(concealed& open) complete all as specified and directed. |
| 57 | S&F GI tubing medium gde with all fittings fixed to walls or laid in floors 20mm bore (concealed & open) complete all as specified and directed. |
| 58 | S&F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 59 | S&F in repair 15mm bore CP fancy type (L-Type bend wall mixer , sink mixer & WBH mixer for mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall , WHB, complete all as specified and directed. |
| 60 | S&F in repair stop valve/ Angle cock/ concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as specified and directed. |
| 61 | S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. |
| 62 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. |
| 63 | S&F in repair sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to draft wall including brackets and connecting union to pipe overall size 915x460mm bowl size 410x330x160mm complete all as specified and directed. |
| 64 | S&F Stainless steel plate rack of size 900x750mm with shelves, hooks and railing to keep plates vertically and horizontly, including necessary fixing arrangement, complete all as specified and directed. |
| 65 | S&F of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore complete including dismantling/ taking out of old water tank & removing from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank. |
| 66 | S&F Vitreous Chaina wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces complete all as specified and directed. |
| 67 | S&F in repair of vitreous china squatting pan of Orrisa pattern size 580 x 440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of any pattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed. |
| 68 | S&F Brass with CP finished,Jet spray with flexible pipe of suitable length fixed to 15mm bore pipe (faucet) complete all as specified and directed. |
| 69 | M&L for plastic water closet seat cover white closed pattern withflat bottom mild steel chromium plated or aluminium hinging device fixed in repair complee all as specified and directed. |
| 70 | S&F in repair 10 Ltrs capacity virgin polypropylene cistern, syphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed sufaces in CM 1:3 to match with the existing surface, complete all as specified and directed. |
| 71 | S&F in repair vitreous china wash hand basin white flat back or angle back type size 600mm x 480 mm white incl waste pipe and prop stopper but incl cutting for and pinning in ends of brackets or erecting stand fixed, complete all as specified and directed. |
| 72 | S&F in repair 600x450 mm beveled edge mirror of selected glass mounted on 6mm tick AC building board or commercial plywood and fixed to wooden on plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 73 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. |
| 74 | S&F in repair soap dish chromium plated of size 180x160x90mm any type, fixed complete all as spd.o plugs with chromium plated brass screws complete all as specified and directed. |
| 75 | S&F in repair brass chromium plated tabular towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed. |
| 76 | M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains, incl fair finished & necessary formwork complete all as specified and directed. |
| 77 | S&F in repair CP shower rose heavy duty with swivel joints 125 mm dia fixed to 15mm GI pipe complete all as specified and directed. |
| 78 | Dismantling of 100mm cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches/ floor/ wall if required complete all as specified and directed. |
| 79 | S&F PVC (SWR) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or in floors etc complete all as specified and as directed. |
| 80 | S&F PVC (SWR) 75 mm pipe single socket in any length with rubber ring joints fixed to wall or in floors etc complete all as specified and as directed. |
| 81 | S&F in repair of 110mm bore PVC (SWR) bends any radius including jointing with solvent cement complete all as specified and as directed. |
| 82 | S&F 110mm dia PVC (SWR) \\"P\\" /'S' trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified and directed. |
| 83 | S&F 75mm dia PVC (SWR) bends with oval accesse /plain door with rubber ring joints fixed as required complete all as specified and directed. |
| 84 | S&F 75mm dia PVC (SWR) floor trap, plain with SS grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified and directed. |
| 85 | M&L for preparation of new or previourly untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & appyling two coats of synthetic enamal paint over a coat of pink primer complete all as specified and directed. |
| 86 | M&L for preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 87 | M&L for preparation of old painted steel surfaces including preparation of surfaces and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 88 | M&L for complete removal of old plastered surfaces of walls and applying two coats of exterior emulsion paint & over one coat of primer etc, complete all as specified and directed. |
| 89 | M&L for preparation of old decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed. |
| 90 | Complete removal of existing old surfaces applying two coats of oil bound distemper over one coat of wall putty(2mm) on walls complete all as specified and directed. |
| 91 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 92 | S&F structural steel work as in roof trusses (framed), trussed , purlins crane gantries, rails & fastenings & heavy bracketsframing (beam, tee, angle, gusset plate,channel or flat section including distance pieces,cleats etc, structural steel confirming to Fe-410w, Gde 250, quality 'A' complete all as specified and directed. |
| 93 | S&F mild steel framed work as in grills,guard bars,iron door,ladders etc. with ends of bars shouldered/welded and/or riveted and other simillar works confirming to Fe410-0 or Fe310-0 complete all as specified and directed. |
| 94 | Taking out sludge including removing blockage and cleaning the sewage line (n-exc 200 mm dia) by using bamboos sticks, MS rod or other sticks or mechinacal jetting machine and revolving the rope inside the sewer between the two man holes for following sizes of sewar and cleaning the same by fresh water complete all as specified and directed. |
| 95 | Taking out sludge including blockage and cleaning of the MH of any size, description, depth n exc 1.50m each and collection the sludge in closed container and cleaning the man holes with fresh water and reopenning of manholes complete all as specified and directed. Note :- Sludge be lifted and taken to out sides of MoD land as directed by Engr-in-Charge and be inclusive of transport. |
| 96 | Taking out sludge including blockage and cleaning of the Septic Tank/Deep line Man holes of any size, description, depth exc 1.50m and n exc 3.00m each.the sludge in closed container and cleaning the septic tank/ Deep man holes with fresh water and reopenning of manholes complete all as specified and directed. Note:- Sludge be lifted and taken to out sides of MoD land as directed by Engr-in-Charge and be inclusive of transport. |
| 97 | S&F in repair of galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed. |
| 98 | S&F in repair of sheet glass 3mm thick, ordinary quality, in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters complete all as specified and directed. |
| 99 | M&L for non skid coloured ceramic tiles 400x400x7to8mm set & jointed with neat cement slurry & pointed in white/coloured cement to match the tiles over 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Please Enable Macros to View BoQ information |
