|
| 1 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed. |
| 2 | Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick all as directed. |
| 3 | M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed. |
| 4 | M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 5 | M&L for Non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,(300x300)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 6 | M&L for Non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,(400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 7 | M&L for vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed |
| 8 | M&L for Vitrified Ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm (600 x 1200)mm , in floors etc. laid over and including roughning existing surface, making good the damaged surface, levelling and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 9 | -Ditto- as per ser item No 08 above but on skirting and backing coat of 10 mm thick in CM 1:4 |
| 10 | M & L for Chequred cement concrete tiles with pigment 25 cm x 25 cm x 22 mm thick, set, jointed and pointed in neat cement slurry as in floors over and including screed bed of 15 mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge |
| 11 | M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge |
| 12 | M&L 15-18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed. |
| 13 | M&L machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed. |
| 14 | M&L for 20 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed |
| 15 | Fixing only 20mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed |
| 16 | M&L for heavy duty vitrified paver tiles 30cm x 30cm x 10mm thick,approved by GE withnset,jointed and pointed in neat cement slurry with grey cement and pigment to match in floors,over and including screed bed or bedding a layer of 15 mm in cement mortar 1:6 complete all as specified and directed by Engg-in-charge. |
| 17 | Demolition of plain cement concrete solid block/ stone/ brick masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed. |
| 18 | M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge |
| 19 | M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 but except stone complete all as specified and directed by Engineer-in-Charge |
| 20 | M & L for pre-cast cement concrete solid blocks, exc. 10 cm in width type C-5 1:5:10 using 20 mm graded aggregates and setting in cement mortar 1:6 complete all as directed. |
| 21 | Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed |
| 22 | M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed. |
| 23 | M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed. |
| 24 | M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair without using extra cement all as specified and directed. |
| 25 | M&L for preparation of new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed. |
| 26 | M & L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffoldingetc complete all as directed. |
| 27 | M&L for 1 mm wall care putty on walls complete all as specified and directed by Engg-in-charge. |
| 28 | M & L for complete removal of existing treatment, washing, rubbing down and stopping of distempered and painted surface of walls and apply two coat of luster (any tint) over a layer of wall care putty & a coat of suitable primer complete all as specified and directed. |
| 29 | Dismantling of single layer manglore pattern in roofing & removing all rubbish/dismantled material outside MD Land.all as directed. |
| 30 | -ditto- all as per ser item no 29 above but bedded in cement morter |
| 31 | M&L for roofing tile, manglore pattern interlocking at sides joints laid dry |
| 32 | -ditto- all as per ser item no 31 above but except manglore pattern tiles |
| 33 | M&L Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement morter 1:6 |
| 34 | Dismantling in fillets,rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/dismantled material outside MD Land. |
| 35 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge & removing all rubbish/dismantled material outside MD Land.all as directed. |
| 36 | S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge. |
| 37 | Supply and fix Pre-painted 0.50 mm thick plain, galvanised sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge. |
| 38 | S&F Steel work in tubular trusses Roof trusses (framed) of section Rectangular/square/circular, post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 2014 and IS 4923- 2017 grade St.-240 |
| 39 | M&L for filleting in any position in repairs and to any shape in cement and sand mortar (1:4) including all mitres, stops etc exc 25 Sqcm but n.exc 50 Sqcm etc complete all as specified and directed by Engineer-in-Charge |
| 40 | Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed. |
| 41 | S&F in repairs vitreous integrated one peice floor mounted china wash down water closet (Pedestral pattern) white as approved by GE including necessary fittings, fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device etc complete all as specified and directed by Engineer-in-Charge connecting to P or S trap etc complete all as specified and directed by Engineer-in-Charge.(Ceremic Parryware, Cat No:C8995 Inslim or equivalent make) |
| 42 | Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed. |
| 43 | Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed. |
| 44 | S&F fix in repairs wash hand basin with pedestal vitreous China white , flat back or angle type of size 500 X 400 mm incl pedestral etc complete all as specified and directed by Engineer-in-Charge |
| 45 | Supply and fix in repairs ceremic table top wash hand basin vitreous China, as approved by GE,including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed. (Ceremic Cera Cat No.S2020137, Calburt or equivalent make) |
| 46 | M&L for preparation of old unplastered or plastered surfaces and applying one coats of oil bound distempering on walls all as directed. |
| 47 | -ditto- all as per ser item no 46 above above but two coat of OBD on old surface |
| 48 | M & L for complete removal of existing treatment, washing, rubbing down and stopping old distempered and apply a coat of wall care putty over the surface of walls and applying two coats of oil bound distempering on walls all as directed. |
| 49 | M & L for preparation of old plastered or unplastered surface of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot,moulds,moss and efflorescent salt,trading oil and greasy spots and apply one coats of white lime wash at any height including scaffoldingetc complete all as specified and directed by Engineer-in-charge.. |
| 50 | -ditto- all as per ser item no 49 above (here-in-before) but on ceiling. |
| 51 | M & L for preparation of old painted surfaces of wall and applying two coats of cement based paint all as directed. |
| 52 | M & L for preparation ofold painted surfaces of wall and applying one coats of cement based paint all as directed. |
| 53 | M & L for preparation of old plastered treated surface of walls by brooming down and apply one coats of wheather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as directed. |
| 54 | M&L for preparation of old surfaces of wood of any description exc 10cm width/girth incl cleaning applying one coat of synthetic enamel all as specified directed by Engineer-in-charge. |
| 55 | M & L for preparation of old steel and iron surfaces, of any description, over 10 cm width or girth not other wise described and applying one coats of synthetic enamel paint over a coat of red oxide primer |
| 56 | Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed. |
| 57 | Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed. |
| 58 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge. |
| 59 | S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified. |
| 60 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 61 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as directed by Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 62 | Supply and fix 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides |
| 63 | Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed. |
| 64 | Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed. |
| 65 | Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face |
| 66 | Supply and fix stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed. |
| 67 | Supply and fix for 3 mm thick sheet frosted/pin headed glass in squares n exc 0.50 sqm in each pane Please Enable Macros to View BoQ information |
| 68 | Supply and fix for 3 mm thick sheet frosted/pin headed glass in squares n exc 0.50 sqm in each pane Please Enable Macros to View BoQ information |
