|
| 1 | Annexure-A (LABOUR CHARGES) |
| 2 | Fabrication of MS Channel angle iron etc in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESPO schedule and local approved drawing. |
| 3 | Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work |
| 4 | Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in 11 KV Line |
| 5 | Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work. |
| 6 | Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual. |
| 7 | Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8(1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual |
| 8 | Muffing of poles size 0.45x0.60 cm radius with 1:3:6(1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement, stone and sand etc. |
| 9 | Dismantling of existing HT line including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Rabbit) |
| 10 | Painting of SP-55 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level. |
| 11 | Route cleareance by cutting of tree branches / proning, loping and chopping of trees for L.T., 11 & 33 KV line. |
| 12 | Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 0-20 Km) |
| 13 | Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 0-20 Km) |
| 14 | Headload cartage of SP-55 Pole from road to site (distance 1-3 Km) |
| 15 | Headload cartage of small material(distance 0-1 Km) |
| 16 | Service of Hydra Machine for Lines and Transformer related work because of busy traffic in Town area for safety purpose. |
| 17 | Tightening of Stay Set |
| 18 | Fixing of IPC with AL. Bail for Earthing. |
| 19 | Opening of 11 KV Jumper and Making again of section pole |
| 20 | Fixing of 11 KV Suspension Ties. |
| 21 | Fixing of 11 KV IPC for CC to Bare Conductor. |
| 22 | Fixing of 11 KV Mid Span Jointing Kit. |
| 23 | Digging of Pit and straightning of tilled pole. |
| 24 | Laying Spreading, Stringing AAAC Conductor. |
| 25 | Back Carriage of scrap material |
| 26 | Annexure-B (SUPPLY ITEMS)(As per UPCL Norms) |
| 27 | Supply of Holding Clamp for SP-55 with N/B |
| 28 | Supply of Stay Clamp for SP-55 with N/B |
| 29 | Supply of IPC with Al. BAIL for Earthing 11 KV |
| 30 | Supply of 11 KV IPC for Covered to Covered Conductor. |
| 31 | Supply of 11 KV IPC for Covered to Bare Conductor. |
| 32 | Supply of 11 KV mid span Jointing Kit |
| 33 | Supply of 11 KV Sus. Ties/Cable Ties for Pin Insulator |
| 34 | Supply of 11 KV AAAC Covered Conductor AL-59, 99 Sq.mm. |
| 35 | Supply of 11 KV Tension Clamp with BAIL & IPC Please Enable Macros to View BoQ information |
