|
| 1 | Labour charges for installation of submersible motor pump set including lowering/ delowering of pipes, cables, accessories etc. in tube-well/ open well complete including T&P, transportation of tripod, chain pulley block & any other material required for this purpose complete in all respect.Delowering and Lowering |
| 2 | SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM |
| 3 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .2.0 HP to 3.0 HP (DOL starter) |
| 4 | Supply & fixing of GI pipes confirming to IS : 1239 P - 1 ( 2004 ) with flanges duly screwed & welded including rubber washer, nuts & bolts of 8mm dia complete in all respect.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .B class 32mm dia |
| 5 | Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/1992) of grade Fe410 of following nominal bore sizes at site of work.150mm dia |
| 6 | Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .12mm (suitable up to 50 mm OD pipe) |
| 7 | M.S. clamp set made of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 8 | Supply and fixing of tube well cover of M.S. sheet (6mm thick) with nuts and bolts complete for casing size:150mm dia |
| 9 | Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .63 mm OD 6 kg / cm2 |
| 10 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4 Sq.mm 3 core flat / Round |
| 11 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6.0 Sq. mm 4 core |
| 12 | Motor opening cable jointing & refitting charges when rewinding is not required. |
| 13 | Providing and replacement of G.M./S.S. bushes for all types of motor including cost of sleeves |
| 14 | Providing and replacement of thurst bearing for all types of motor.It includes cost of all components connected with thurst bearing |
| 15 | Replacment of thurst plate of all type of motors |
| 16 | Supplying and fixing spare parts for repair of pump set including cost of opening refitting , servicing and machining if required . It also includes the cost of nut bolts, studs, washer packing,keys etc. complete.Providing and fixing of GM neck rings parts on impeller. |
| 17 | Providing and fixing of GM/SS bush per piece |
| 18 | Providing and fixing of G.M. impeller |
| 19 | Providing and fixing of C.I. diffuser /guide vans per piece |
| 20 | Providing and fixing of gun metal diffuser /guide vans per piece |
| 21 | Providing and fixing of C.I. body per piece |
| 22 | Pump opening and fixing including machining & all finishing work for desired performance. |
| 23 | Impeller welding and turning (If not replaced) |
| 24 | Repair rewinding of single phase submersible motor including full servicing and rewinding as per menufecturer's specification and to the specification of Enginee in charge. It includes replacement of minor parts such as bushes (oil seal bush) Nut bolts, washers, cable seals, gland ring, vent plug, water drain plug, etc. complete job. Upto 2 HP |
| 25 | Providing and replacement of G.M./S.S. bushes for all types of single phase submersiblle motor including cost of sleeves |
| 26 | Providing and replacement of thurst bearing for all types of single phase submersiblle motor.It includes cost of all components connected with thurst bearing |
| 27 | Providing and replacement of thurst plate for all types of single phase submersiblle motor. |
| 28 | Providing and fixing of motor pump coupling housing set |
| 29 | Providing and fixing of NRV for single phase submersible motor |
| 30 | Providing and fixing of S.S. shaft for single phase submersible motor upto 2 HP |
| 31 | Supplying and fixing of spare parts for monoblock pump setConnection platesUpto 10 HP |
| 32 | Cooling FanUpto 10 HP |
| 33 | Mechanical reconditioning of Bearing sheetUpto 10 HP |
| 34 | Mechanical reconditioning of Impeller sheet and Key way slotUpto 10 HP |
| 35 | Oil SealUpto 10 HP |
| 36 | Labour charges for opening and fiting of pump setsUpto 10 HP |
| 37 | Labour charges for repairing of starter at site including opening and reassembling of starter with labour charges for repalcing of defective parts with new one at site. (Parts will be provided by UMC)5 to 15 HP Please Enable Macros to View BoQ information |
