|
| 1 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 2 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 3 | Earth filling in foundation trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) |
| 4 | Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 5 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 6 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 9 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 12 | Suspended floors, roofs, landings, balconies and access platform |
| 13 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 14 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Weather shade, Chajjas, corbels etc., including edges |
| 16 | Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 17 | Providing designation 125mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 18 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 19 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 20 | Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 21 | Providing Tor steel reinforcement of 8mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(a) 10mm (TMT coil Fe 500) (only valid for SAIL & TATA STEEL) |
| 22 | Providing Tor steel reinforcement of 12mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(b) 12mm & Above (TMT coil Fe 500) (only valid for SAIL & TATA STEEL) |
| 23 | Providing Tor steel reinforcement of 16mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(c) 16mm & Above (TMT coil Fe 500) (only valid for SAIL & TATA STEEL) |
| 24 | Providing Tor steel reinforcement of 20mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(a) 20/25mm (TMT coil Fe 500) (only valid for SAIL & TATA STEEL) 50% of Total Steel |
| 25 | Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 26 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 27 | Kota stone slabs flooring over 20 mm thick (average) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete with base of cement mortor 1:4 (1 cement : 4 coarse sand )25mm thick |
| 28 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 29 | Providing and laying Double charge virtified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @3.3 kg/sqm including grounting the joints with white cement and matching pigments etc. complete Size of Tile 600x600mm |
| 30 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm |
| 31 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.With commercial grade colour tiles. |
| 32 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, includinghinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded orrigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb |
| 33 | Supplying, fitting and fixing 250X20X6mm L-type M.S clamp properly fishtailed, including maiking holes and setting as same in 250X125X75mm. Cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and direction of E/I. |
| 34 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to beprovided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specificationand direction of Engineer- in-Charge. |
| 35 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.30 mm thick pre laminated PVC door shutters |
| 36 | Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 37 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flat/ Square as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 38 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 39 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 40 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 41 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 42 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 43 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 44 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 45 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 46 | Supply and 'Labour for fabricating, erecting, hoistion and fixing in position structrral steel work in R.S. Joist, channel, Angle, Tee, flat, plate, latice member, built up compound section in column, girder, stair case, or truss including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding ( machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing, building specification and direction of E/I. |
| 47 | Labour for fitting and fixing G.C.I. Or C.A. Sheet roofing in proper slope including the cost of \\"J\\" or \\"L\\" hooks, limpet and bitumen washers, carriage of sheet to work site, and taxes all complete as per building specification and direction of E/I. |
| 48 | Labour for fitting and fixing G.C.I. Or C.A. Sheet ridge including the cost of \\"J\\" or \\"L\\" hooks, limpet and bitumen washers, carriage of sheet to work site, and taxes all complete as per building specification and direction of E/I. |
| 49 | supply of GCI sheet |
| 50 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. |
| 51 | 1X 28 watt T5 tubelight |
| 52 | led flood light 200w |
| 53 | Instalation testing and commissing of pre wired fluorescent fitting. Compact fluorescent fitting of all type complete with all accessories and tube etc directly / wall including connecting with 1.5 sqmm fr pvc insulated copper conductor single core cable and earthing etc as required |
| 54 | CEILING FAN 48\\" (1200MM ) |
| 55 | ITC ceilling fan:-Installation, testing & commissioning of ceilling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper coductor, single core cable etc, as required. |
| 56 | 16\\" ( 400 MM) Wall mounted fan |
| 57 | Point wiring in PVC conduit, with pino type switch:-wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor singal core cable in surface/ recessed PVC conduit with piano type switch, phenolic laminated sheet, suitable size PVC/G.I box ect. asGroup B |
| 58 | Circuit submain wiring in pvc conduit 'wiring for circuit/ submain wiring along with earth ire with the folloeing sizes of fr pvc insulated coper insulated copper conductor single core cable in surfce recessed pvc conduit as required 2x 1.5 sq. mm + 1x 1.5 sq. mm earth wire |
| 59 | Circuit submain wiring in pvc conduit 'wiring for circuit/ submain wiring along with earth ire with the folloeing sizes of fr pvc insulated coper insulated copper conductor single core cable in surfce recessed pvc conduit as required 2x 2.5 sq. mm + 1x 2.5 sq. mm earth wire |
| 60 | Circuit submain wiring in pvc conduit 'wiring for circuit/ submain wiring along with earth ire with the folloeing sizes of fr pvc insulated coper insulated copper conductor single core cable in surfce recessed pvc conduit as required 2x 6 sq. mm + 1x 6 sq. mm earth wire |
| 61 | S/F S.P. MCB DB:-Supplying & fixing following way single pole neutral, sheet, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate,interconnections, phosphatized & powder painted including earthing etc. as required. (But wihtout MCB/RCCB/Isolator)8 way, Double Door |
| 62 | 50/63 amps ratting, SP MCB \\"C\\" series 10 ka breaking capacity |
| 63 | laying of one no. pvc insulated & pvc sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 950sq mm but not exciding 185 sq mm direct inground including exacavation, sand cushion, protection covering and refilling the trenches etc. as required |
| 64 | S/F PVC/ G.I Boxes:-Supplying & fixing PVC/ G.I box of following sizes on surface or in recess withsuitable size of phenolic laminated sheet cover infront including painting etc. ad required.210 mm x 206 mm x 48mm deep / (10\\" x 12\\") |
| 65 | S/F Piano type switch/ socket:- Supplying & fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.3 pin 5/6 amps, socket outlet |
| 66 | S/F Piano type switch/ socket:-Supplying & fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.5/6 amps, one way switch |
| 67 | S/F Modular type switch socket - Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required 5/6 amps, 3 pin socket outlet |
| 68 | S/F Modular type switch socket - Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required Telephone socket outlet |
| 69 | S/F Modular type switch socket - Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required TV antenna socket outlet |
| 70 | S/F Modular boxes, base & cover plate - Supplying and fixing following size/modules G.I. box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 module (78mm x 78mm x 45mm) |
| 71 | S/F Modualr type blanking plate - Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as required. |
| 72 | Copper earth plate elecrtode - Earthing with copper earth plate 600mmx 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (with charcoal or coke and salt) |
| 73 | S/L 8 SWG copper wire in ground - Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required |
| 74 | P/F 25mmx 5mm G.I. earth strip in ground - Providing and fixing 25mm x 5mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 75 | P/F G.I. lightning conductor finial - Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required. |
| 76 | Reverting, sweating and soldering lightning conductor tape - Reverting, sweating and soldering of copper/G.I. tape (with another copper/G.I. base of the final or any other metalic object) as required. |
| 77 | Fixing lightning conductor tape in vertical run - Fixing of copper/G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor as required. (For vertical run) |
| 78 | P/F Testing joint G.I. lightning conductor - Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos. of G.I. bolts, nuts, check nuts and spring washers etc. complete as required. |
| 79 | P/F G.I. earth tape for lightning conductor - Providing and laying G.I. tape 32mm x 6mm from earth electrode directly in ground as required. |
| 80 | ITC exhaust fan upto 450 mm sweep - Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required. |
| 81 | 12\\" (300mm) metal exhaust fan |
| 82 | 15\\" (380mm) metal exhaust fan |
| 83 | S/F Modular type electronic fan regulator -Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 84 | Supply, Installation, Testing and Commissioning of following size fan 3 Blades confirming to IS:374:2019 including wiring the down rods of stranded for 230 V 50 Hz, single phase supply etc. complete as required 1200mm (48\\") BLDC 5star rating 32W Ceiling Fan |
| 85 | PLUMBING Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.(A) 580 mm long(c) with 10 lit. Low level PVC Cistern |
| 86 | Providing and fixing male ended 15mm dia brass bib cock of approved quality(Wt. Not less than 350gms.)with extra socket all complete as per specification and direction of E/I. |
| 87 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 88 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 89 | (ii) C.P brass dish container medium quality with screw and hinges etc. |
| 90 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore |
| 91 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore |
| 92 | (b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. Brass revolving fitting 3mm ply wood board and C.P. Hinges to fix with mirror.(i) 600mm X 450mm size |
| 93 | Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. Approved make supported on painted C.I. Or R.S. Bracket 32mm C.I. Brass waste, 15 mm dia C.I. Body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plunber joints etc. all complete as per specification and direction of E/I. |
| 94 | Providing and fixing PTMT grating of approved quality and colour.Circular type,125 mm nominal dia with 25 mm waste hole |
| 95 | Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitting,I/C fixing the pipe with clamps at 1.00 m spacing this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing direction of engineer in charge.Concealed work, including cutting chasesand making good the walls etc.20 mm nominal outer dia Pipes |
| 96 | Providing & fixing PVC pipe fitting with all accessories (Supreme Make)110 mm Door Tee (Supreme) PVC |
| 97 | Providing & fixing PVC pipe fitting with all accessories (Supreme Make)110 mm Plain Tee (Supreme) PVC |
| 98 | Providing & fixing PVC pipe fitting with all accessories (Supreme Make)110 mm Door Bend (Supreme) PVC |
| 99 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 100 | CARRAIGE OF MATERIALSAggregate |
| 101 | Cement |
| 102 | Steel |
| 103 | METAL |
| 104 | Bricks |
| 105 | Unbranded 1+4 Show Case ( 1 Drawer and 4 open shelves(horizontal) material specification: 19mm thick prelaminated particle board of grade II type III of IS:12823/Latest,both side laminated,outer side laminated withshade matching with top shade and fascia shade and havingbalancing laminate of 0.5mm thickness on other side. Size 1200x1220x485 |
| 106 | Floor Standing Display Cabinet withGlass in Wood/Engineered Wood FrameDoor . Number of shelves- 4; Shelves thickness 25mm; Number of close compartment -2Top and bottom section 18mm both side laminated particle board in brown colour, Side section wood or Engineered particle board 18mm thick both side laminated colour browm Size 2000x1000x500 |
| 107 | ModularTable with Particle Board Table Top andWooden/Engineer Wood UnderstructureTable top size 1500x750x25mm, Material Particle board, height of table top 750mm; Material of Understructure Wooden/ Engineered Wood structure (Particle board) thickness 18mmModesty panel made of 18mm thick double side laminated particle board size 1200x250mmTwo side fixed storage unit |
| 108 | Mid-back Revolving Chair of Adjustable height with Wheels and arm restBackrest Height Mid-backLocking available while tilting backrestYesLumbar Support available in Seat BackrestYesArmrest Available in the Chair YesCentre Tilt (Single pivot point at seat center for simple recliningmotion)Mechanism to adjust seat heightHydraulic MechanismCHAIR SEATAvailability of cushion on seat YesSeat upholstery material Polyester fabricMinimum Chair Seat height (in mm) 400Minimum Height Adjustment Range of Seat (in mm) 100 mmColour Family of Seat Black |
| 109 | Unbranded Office Chair Non-revolving and non-tilting chair with armrest Chair understructure type Legs Understructure material Mild steel The shape of tubular section of understructure RoundSection Size (Diameter/Sides) of understructure 19 mm Understructure wall thickness(mm) 1.2 SEAT Seat base material Hot pressed plywood Seat material PU foam Density of PU used in seat (kg per cubic meter) 45 Thickness of PU 40 millimeter Seat height from floor surface (mm) 440 width of seat (mm) 440 millimeter Depth of seat (mm) 450 millimeter Seat upholstery material Leatherette |
| 110 | Steel Spherical Vane Design Wind Ventilator, 42 vanes, Al 0.5mm thick, Alloy 8011. Neck and Throat diameter 490mm, Vanes 42 nos AL. 0.5mm thick alloy Bottom ring diameter 620mm Rotation Twin seales integrated bearing housing consisiting of 2 nos deep grooved ball bearing 6002-2Z permanently lubricated and sealed. |
| 111 | Add GST @18% |
| 112 | Add Labour Cess @1% |
| 113 | Consultancy charges @1.35% Please Enable Macros to View BoQ information |
