|
| 1 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (As per DSR 4.17) |
| 2 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (As per DSR 8.31) |
| 3 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (As per DSR 9.21.1) |
| 4 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only (As per DSR 9.22.1) |
| 5 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike¬ plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer¬ in-charge:10.14.2 Profile C Fixing with adjustable lugs with split end tail to each jamb (As per DSR 10.14.2.1) |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes (As per DSR 10.16.1) |
| 7 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (As per DSR 10.28) |
| 8 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement (As per DSR 11.20.3) |
| 9 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.1 Double charge vitrified tile polished finish of size Size of Tile 600x600 mm (As per DSR 11.41A.1.1) |
| 10 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (As per DSR 11.55.1) |
| 11 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (As per DSR 12.21.1) |
| 12 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) (As per DSR 13.1.1) |
| 13 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) (As per DSR 13.2.1) |
| 14 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing (As per DSR 13.31.1) |
| 15 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (As per DSR 13.46.1) |
| 16 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat (As per DSR 13.82.1) |
| 17 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) (As per DSR 14.5.1) |
| 18 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. (As per DSR 15.3) |
| 19 | Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (As per DSR 16.68) |
| 20 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (As per DSR 16.69) |
| 21 | Providing and laying antiskid ceramic floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 mm. (N.S.) |
| 22 | Providing and fixing 1.5mm thick polycarbonate sheet to be fixed on the existing MS frame with self drilling machine screws complete in all respect to the entire satisfaction of Engineer-in-charge. (N.S.) |
| 23 | Providing and fixing of roller blind of make \\"Wishade (code 2129)\\" with complete accessories including the cost all required fittings complete in all repsects and to the entire satisfaction of the Engineer in charge (N.S.) |
| 24 | P/F 110 mm internal dia PVC pipe as rain water pipe on walls of 6kg./sqm, pressure with Bend, Elbow and Clamps complete in all respect to the satisfaction to the Engineer-in-charge. (N.S.) |
| 25 | Providing and fixing 2'-0\\" deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 1 mm thick mica on the exposed surface and making shelves in cabinet. The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos. fancy s.s. handles, 2 nos. magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface complete in position as per entire satisfaction of Engineer-in-charge. (N.S.) |
| 26 | Providing and fixing wooden cabinet of 13½” deep and 2’-0\\" height with open able shutter at wall above 4’-9\\" height consisting of 19mm thick with commercial board (ISI marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, auto hinges, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in al respect to the entire satisfaction of Engineer in charge. (N.S.) |
| 27 | Retile terracing of mud phaska covered with tiles or brick, in cement mortar by reusing dismantled tile or bricks after cleaning and making tile servicalbe for reuse, dismantling mud phaska and cleaning the mother slab propoerly (75mm old earth and 25mm new earth) after performing water proofing treatment which will be paid seperately. Laying 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat brick tile, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat including replacing unserviceable tiles or bricks with new ones (the cost of the new tiles/bricks excluded) all complete as per direction of Engineer-in-Charge. (N.S.) |
| 28 | Providing and Fixing Water proofing treatment with (MAK polyplast regular grade 2104 or equivalent) 1mm thick weighing 1.75 kg/sqm over the surface with one coat of bitumen 85/25 @1.20 kg/sqm fixing polyplast over laps sealed with flame of blown bitumen and another coat of hot bitumen 85/25 @ 1.20kg/sqm over the polyplast sheet including cost of sealing the overlap 10cm width complete in all respect to the entire satisfaction of Engineer-In-Charge. (N.S.) |
| 29 | Supply of 1st quality brick tiles designation 100 with size 9\\" X 4 1/2\\" X 1 1/2\\" complete in all respects to the entire satisfaction of Engineer in charge (N.S.) |
| 30 | Providing and fixing of cupboard shelves consisting of 19mm thick commercial board (ISI marked) phenol bonded fixed with hard wood battens and gutties including the cost of necessary lipping screws nails fevicol and two coats of special quality paint over one coat of primer after preparation of surface complete in all respect and to the entire satisfaction of the Engineer in charge. (N.S.) |
| 31 | Providing and fixing M.S. tubular window shutters consisting of styles, top rail and bottom rail of M.S. tube 60mmx30mm made out of 18 gauge M.S. sheet having 12mm rebate. The shuters to be made by cutting mitered joints electrically flash welded and grinding smooth, the rate includes the cost of 2 no.s bright finished or black enameled mild steel butt hinges 100x58x1.90mm. The rate further includes one coat of ready mixed red oxide zinc chromate primer of aprroved brand and manufacture and fixing the shutter to the existing frame complete in all respects and to the entire satisfaction of engineer in charge (Rate further includes making holes in frames and providing clips for fixing glass panes) (N.S.) |
| 32 | Providing and applying cement based putty (Birla, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge. (N.S.) Please Enable Macros to View BoQ information |
