|
| 1 | Surface dressing n.exc 15cm deep in soft/loose soil etc complete all as directed. |
| 2 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm etc complete all as directed. |
| 3 | M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed. |
| 4 | M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) all as specified. |
| 5 | M&L for 10mm thick rendering on wall surfaces in CM 1:4 finished even & fair etc complete all as specified and directed. |
| 6 | M&L for hardcore of broken or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed. |
| 7 | M&L Moorum/red bajri filling in floors or pavings, laid in layers n.exc. 15cm thick, spread and levelled including watering and ramming all as specified and as directed. . |
| 8 | M&L for 100mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed. |
| 9 | M&L for PCC (1:2:4), Type B1, using 20 mm graded aggregates, 100 mm thick, incl all necessary forwork required and finishing the concrete surface even and smooth without using extra cement. |
| 10 | M&L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `A' complete all as specified and directed. |
| 11 | M&L for forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' etc complete all as specified and directed. |
| 12 | S&F Mild Steel of gde Fe 410-W as in plain plates cut to required sizes including forming holes without any attachement etc complete all as specified and directed. |
| 13 | M&L for mild steel work tubular pipes as in posts/truss/purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as specified and directed. |
| 14 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc complete all as specified and directed. |
| 15 | S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified. |
| 16 | S&F MS works as in wind ties for roof incl securing bolts etc complete all as specified and as directed. |
| 17 | M&L preparation of newly steel surfaces exc 10cm width or girth and applying 2 coats of synthethic enamel paint over a coat of primer etc complete all as specified and directed. |
| 18 | all as per Item no 17 above above but n.exc 10cm width or girth |
| 19 | M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including concealed/ surface PVC conduit and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets,fan regulators etc. all as specified and as directed forthe following:- One light point controlled by one switch |
| 20 | all as per item No 19 above One 3 pin switch socket outlet point 5 amps on same board with other switches |
| 21 | all as per item No 19 above One 3 pin switch socket outlet point 5 amps on independent board |
| 22 | all as per item No 19 above here-in-before but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings complete all as specified and as directed. |
| 23 | Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed. |
| 24 | Supply and fix switch socket combination 2 in 1, 3 pin (mult pin) 5 amps flush type, complete all as specified and as dircted by Engineer-in-Charge. |
| 25 | Supply and fix switch socket combination outlet, 2 in 1, 3 pin 15 and 5 amps, controlled by one switch flush/box type complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Supply and fix ceiling rose surface bakelite 65x50mm 3 terminal complete all as specified and as directed. |
| 27 | Supply and fix metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, double door suitable for mounting MCBs including taking down old MCB/DB complete all as specified and directed.Note-: Incoming & outgoing connections from the DB shall be provided with proper lugs/ thimbles etc |
| 28 | Supply and fix MCB single pole 240 volts, 6 to 32 amps \\"B\\" series complete all as specified and as directed by Engineer-in-Charge |
| 29 | Supply and fix single pole and netural 240 Volts 32 amps complete all as specified and as directed by Engineer-in-Charge |
| 30 | Supply & fix LED Highbay with pressure die cast housing light fittings 80 watts, Energy saving, environment friendly & robust open type vertical Highbay LED IP 66 luminaire, 5 kV inbuilt surge protection including driver and required GI tube down road with hoooks for hanging the fitting. The fitting including fixing arrangements complete etc. The fitting shall conform to Cat No.TIP-323-80-57-60D-HL2-NS-LM-NSG of Crompton / Havells /Bajaj/ Philips |
| 31 | S&F 35 W LED street light fitting 230 V AC outdoor type with pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25/32 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed. |
| 32 | M & L for circuit wiring complete with two runs of 1.5 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Conduit and all accessories fixed to wall/ roofs/ floors etc with one run of 1.5 sqmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories,complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of conduit & one run of earth continuity conductor shall be measured as one running metre. |
| 33 | M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less thab 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I |
| 34 | supply & Lay XLPE insulated, heavy duty 1100 volt grade electric armoured LT UG cable with aluminium conductor of size 10 Sqmm 2 Core in trenches/along the wall/including making all connections, saddles, spacers including scaffolding if any required for saddling the cable in walls of building of height up to 25 meter, complete with aluminium lugs as required at site and as directed by Engr-in-Charge |
| 35 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out Soft/loose Soil |
| 36 | Returning, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25cm soil / hard dense soil. |
| 37 | Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point.Soft Soil / hard dense soil |
| 38 | Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed. |
| 39 | S&F 50 mm bore GI tube light grade galvanised with all fittings laid in trenches complete as directed. |
| 40 | Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge. Please Enable Macros to View BoQ information |
