|
| 1 | Earth work |
| 2 | Earth work in excavation in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock) including banking in 20 cm layers and breaking clods, ramming and dressing up for the purpose of making embankments or filling up ground depressions, lead upto 50 m and lift upto 1.50 m. |
| 3 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 4 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 5 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 6 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : |
| 7 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. |
| 8 | Dry stone pitching 22.50 cm thick including supply of stone and preparing surface complete (including carriage of stone for 5 km lead). |
| 9 | C. C. work |
| 10 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 11 | R. C. C. work |
| 12 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : . M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 13 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. .M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 14 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 15 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement withM20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 16 | Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers bands and facias up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding the 6 mm to give a smooth and even surface but excluding the cost of centering, shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 fine sand : 4 stone aggregate 12.5 mm nominal size). |
| 17 | Reinforcement of R C C work including bending, binding and placing in position complete, b) Tar/ TMT steel |
| 18 | Centring and shuttering including strutting, propping etc and removal of form work for : |
| 19 | Foundation, footings, bases of columns etc. and mass concrete. |
| 20 | Column, pillars, posts and struts etc. |
| 21 | Lintels, beams, girders, bressumers and cantilevers etc. |
| 22 | Suspended floors, roofs, landings shelves and their supports, balconies and chajjas ( 3.5 m height). |
| 23 | Vertical and horizontal fins individually or forming box louvers bands and facias. |
| 24 | Brick work |
| 25 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:5 (1 cement : 5 fine sand). |
| 26 | Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level. |
| 27 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement : 4 coarse sand) in foundation and plinth. |
| 28 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 29 | WOOD & PVC Work |
| 30 | Providing and Fixing factory made WPC door frame made of WPC extruded sections of size 125 mm x 63 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with WPC profile..including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer- in-charge. |
| 31 | Providing and fixing 35 mm thick factory made WPC Door shutter, styles and rails made of WPC non hollow extruded printed and laminated section & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer's specification and direction of engineer-in-charge. |
| 32 | PVC Door Frames:- Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge. |
| 33 | Entry/Exit Door Shutters :- Providing and fixing 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For WC and bathroom door shutter). |
| 34 | Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. |
| 35 | Ornamental grill |
| 36 | Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size). |
| 37 | Providing and fixing stainless steel sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. |
| 38 | 300 x 16 mm |
| 39 | Providing and fixing stainless steel bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. |
| 40 | 300 x 10 mm |
| 41 | Providing and fixing stainless steel Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. |
| 42 | 125mm |
| 43 | Providing and fixing stainless steel hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 44 | Twin rubber stopper. |
| 45 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 46 | Providing and fixing chromium plated brass 150 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 47 | Steel work |
| 48 | Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint. |
| 49 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, |
| 50 | Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete. |
| 51 | Flooring work |
| 52 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., completea) Size of Tile 600x600 mm |
| 53 | Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar1:3 (1cement:3coarsesand), including grouting the joint with white cement & matching pigments etc. completea)Size of Tile 600x600 mm |
| 54 | White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry. |
| 55 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Makrana white second quality |
| 56 | Extra for pre finished nosing to treads of steps of marble stone. |
| 57 | Pre-cast terrazzo tiles 20 mm thick with white, black or white and black marble chips of sizes up to 6 mm laid in floor, treads of steps and landings on 25 mm thick bed of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete with pre-cast tiles of :a) Dark shade using ordinary cement. |
| 58 | Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor. |
| 59 | 21 mm thick. |
| 60 | Roofing work |
| 61 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening“for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK. |
| 62 | Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). |
| 63 | 100 mm diameter pipe |
| 64 | Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. |
| 65 | 100 mm diameter pipe |
| 66 | Finishing work |
| 67 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand) . |
| 68 | 15 mm cement plaster 1 : 5 (1 cement : 5 fine sand) on the rough side of single or half brick wall. |
| 69 | 6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand). |
| 70 | Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 71 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 72 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade. |
| 73 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 74 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade |
| 75 | Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work. |
| 76 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 77 | Miscelleaous Work |
| 78 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 79 | Brick edging 7.50 cm wide and 12.50 cm deep to plinth protection with 2nd class bricks including grouting with cement mortar 1 : 4 (1 cement : 4 fine sand). |
| 80 | Drainage Work |
| 81 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 82 | Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. |
| 83 | 100 mm dia SW pipes |
| 84 | Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. |
| 85 | 100 mm dia SW pipes |
| 86 | Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. |
| 87 | Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg). |
| 88 | Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honey comb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design. |
| 89 | Water Supply Work |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 91 | 15 mm nominal bore |
| 92 | 20 mm nominal bore |
| 93 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work |
| 94 | 25 mm nominal bore |
| 95 | Providing and fixing brass bib cock of approved quality. |
| 96 | 15 mm nominal bore |
| 97 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 98 | 15 mm nominal bore. |
| 99 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 100 | 15 mm nominal bore |
| 101 | Providing and fixing brass full way valve with wheel of approved quality. |
| 102 | 25 mm nominal bore |
| 103 | Providing and fixing PVC connection pipe with brass union. |
| 104 | 45 cm length 15 mm nominal bore. |
| 105 | Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. |
| 106 | 150 mm dia |
| 107 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 108 | Samitary Installation Work |
| 109 | Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. |
| 110 | Orissa Pattern WC Pan. |
| 111 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. |
| 112 | Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality. |
| 113 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 114 | Kitchen sink with drain board, i) 510x1040 mm bowl depth 250 mm. |
| 115 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers. |
| 116 | Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws. |
| 117 | Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). |
| 118 | 750 x 20 mm size |
| 119 | Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 120 | 100 x 100 x 100 mm |
| 121 | 80 x 80 x 80 mm |
| 122 | Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. |
| 123 | 100 mm inlet and 100 mm outlet |
| 124 | 100 mm inlet and 75 mm outlet |
| 125 | Providing and fixing CP brass waste for wash basins and sinks. |
| 126 | 40 mm dia |
| 127 | Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. |
| 128 | 100 mm dia SW pipes |
| 129 | 75 mm dia SW pipes |
| 130 | Providing and fixing sand cast iron heel rest sanitary bend. |
| 131 | 100 mm dia |
| 132 | 75 mm dia |
| 133 | Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap . |
| 134 | Painting two or more coats on rain water, soil waste and vent pipes and fittings with black anti-corrosive bituminoustic paint of approve brand and manufacture over a priming coat of ready mixed genuine red lead on new work. |
| 135 | 100 mm dia |
| 136 | Aluminium Work |
| 137 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For fixed portion. Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron). |
| 138 | For shutters of doors, windows & ventilators including providing and fixing hinges /pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron). |
| 139 | Providing and fixing glazing in aluminium door, window, ventilator shutters andpartitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : |
| 140 | With float glass panes of 4.0 mm thickness. |
| 141 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width |
| 142 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. |
| 143 | 255 X 19 mm |
| 144 | (SH;- Internal Electrical Works) |
| 145 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 146 | (Long Point) 'Group \\"A\\" |
| 147 | (Medium Point ) Group \\"B\\" |
| 148 | (Short Point ) 'Group \\"C\\" |
| 149 | Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 150 | Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 151 | Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 152 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required |
| 153 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 154 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 155 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 156 | Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 157 | 1 x 1.5 sq. mm |
| 158 | 2 x 1.5 sq. mm |
| 159 | 4 x 1.5 sq. mm |
| 160 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 161 | 20mm. |
| 162 | 25mm. |
| 163 | Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. |
| 164 | 75 mm X 75 mm X 60 mm deep. |
| 165 | 100 mm X 100 mm X 60 mm deep. |
| 166 | 200 mm X 150 mm X 60 mm deep |
| 167 | 200 mm X 250 mm X 60 mm deep |
| 168 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 169 | 5/6 amps switch |
| 170 | 2 way 5/6 A switch |
| 171 | 15/16 A switch |
| 172 | 3 pin 5/6 A socket outlet |
| 173 | 6 pin 15/16 A socket outlet |
| 174 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 175 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 176 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 177 | Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required. |
| 178 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required |
| 179 | Providing and fixing 16/0.20mm (0.50sqmm) twin flat flexible, FR PVC insulated, copper cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required. |
| 180 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 181 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 182 | Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required. |
| 183 | Installation of exhaust fan in the existing opening, i/c making good the damage, connection, testing, commissioning etc. as required. |
| 184 | Upto 450 mm sweep. |
| 185 | Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required. |
| 186 | 32 Amp TP&N. |
| 187 | 63 Amp TP&N. |
| 188 | Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. |
| 189 | 100 Amp, 16 KA. |
| 190 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 191 | 2 + 6 way, Double door |
| 192 | 2 + 8 way, Double door |
| 193 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 194 | 4 way (4 + 12), Single door |
| 195 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 196 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 197 | 63 amps |
| 198 | 100 amps |
| 199 | Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 30 amps \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 200 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 201 | Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required |
| 202 | 32 Amp TPN. |
| 203 | Supplying, installing, testing and commissioning of following capacity TPN distribution tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, interconnections, earthing etc. as required. |
| 204 | 32 amps TPN, 4 way |
| 205 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 206 | Above 95 sq. mm and upto 185 sq. mm |
| 207 | Providing and fixing of Ceilling fan 1200 sweep of approved quality with required accessory as per specification and direction of Engineer-in-charges . |
| 208 | Providing and fixing of Exhust fan 450 sweep of approved quality with required accessory as per specification and direction of Engineer-in-charges . |
| 209 | Providing and fixing of LED Tube light/Bulbs/Lamp 20 wat of approved quality with required accessory as per specification and direction of Engineer-in-charges . |
| 210 | Earthing with G.I. earth pipe 4.5mtr. long, 40 mm dia including accessories, 'and providing mesonary encloser with cover plate having locking arrangement 'and watering pipe etc. with charcoal or coke 'and salt as required |
| 211 | Earthing with Copper earth plate 600mm x 600mm x 3mm thick including 'accessories, and providing masonary enclosure with cover plate having 'locking arrangement and watering pipe etc. with charcoal or coke 'and salt) as required. |
| 212 | Providing and fixing 1.5….5mm x 5mm G.I.strip in 40mm dia G.I. pipe from earth …. |
| 213 | Supplying and laying 25mm x 6mm G.I.strip at 0.5 metre below ground as 'strip earth electrode, including soldering etc. as required. |
| 214 | GI..'25mm x 3mm |
| 215 | Copper...25mm x 6mm |
| 216 | Providing and fixing main Panel board of approved manufacturer & quality………..as per specification. |
| 217 | (Sh:- RCC Wall) |
| 218 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (without de-watering) |
| 219 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. |
| 220 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical SpecificationsRCC Grade M20/ Using Concrete Mixer |
| 221 | Plain/Reinforced Cement Concrete in sub-structure complete as per Drawing and Technical SpecificationsRCC Grade M20/ Using Concrete Mixer |
| 222 | Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and Technical Specifications, In Footing and Main Wall |
| 223 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification. (A) Granular material |
| 224 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing face. Complete as per drawing and Technical Specifications |
| 225 | Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification. |
| 226 | (Sh:- Boundary wall & Gate) |
| 227 | Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soilcontaining 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edgeof the excavation and returning the stacked soil in 15 cm layers, when required, into plinthCum 171.50sides of foundation etc consolidating each deposited layer by ramming and watering andthen disposing of all surplus soil as directed within a lead of 50m.(a) collumn and wall |
| 228 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone shingle 40mm nominal size) excluding the cost of centring and shuttring. |
| 229 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concreteexcluding cost of centring, shuttering and reinforcement in : |
| 230 | a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 231 | Reinforced cement concrete work in lintels, beams andbresumers up to floor two level includingfinishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) ofthickness not exceeding 6 mm to give a smooth and even surface but excluding cost ofcentering, shuttering and reinforcement. |
| 232 | a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 233 | Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1cement : 3 fine sand). |
| 234 | Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3coarse sand) in foundation and plinth. |
| 235 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 236 | Reinforcement of RCC work including bending, binding and placing in position complete.b) Tar/ TMT steel |
| 237 | Centring and shuttering including strutting proping etc. and removal of form work for: |
| 238 | i)a) Foundation, footings, bases of columns etc. and mass concrete.( For Footing) |
| 239 | ii) e) Column, pillars, posts and struts etc.( for Column) |
| 240 | (iii)d) Lintels, beams, girders, bressumers and cantilevers etc( for Beam). |
| 241 | 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brickwall. |
| 242 | White washing with lime on new work (two or more coats) to give an even shade. |
| 243 | Febrication and fitting and fixing of MS angle of size 45mmX45mmX6mm,embedded 30cm inside the pillars top and 45cm at 45 degree angle with 3 nos of holes. |
| 244 | Providing and fixing of GI barbed wire in MS angle in 5 rows in diagonal with GI staples. Please Enable Macros to View BoQ information |
