Tender For Construction Of Building Including Electrification For Technology And Energy Park In The Premises Of Rtm Nagpur University At Nagpur, Nagpur-Maharashtra

TDR : 54784717

Tender Notice
BOQ

15 Days Left

Nagpur , Maharashtra

Tender Brief : Tender For Construction Of Building Including Electrification For Technology And Energy Park In The Premises Of Rtm Nagpur University At Nagpur

Document Fees
₹ 4040 /-

EMD
₹ 1766000.0 /-

Tender Value
₹ 35.31 Crore /-

Submission Date
08-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area .
2	Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means
3	Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means
4	Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means
5	Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.
6	Providing And Laying Cast In Situ/Ready Mix Cement Concrete In M15 Of Trap/Granite/Quartzite/Gneiss Metal For Foundation And Bedding / Steps Including Steel Centering, Formwork, Laying/Pumping, Compacting, Roughening Them If Special Finish Is To Be Provided, Finishing Uneven And Honeycombed Surface And Curing Etc. Complete. The Cement Mortar 1:3 Plaster Is Considered For Rendering Uneven And Honeycombed Surface, Only. Newly Laid Concrete Shall Be Covered By Gunny Bag, Plastic, Tarpaulin Etc. (Wooden Centering Will Not Be Allowed.),With Fully Automatic Micro Processor Based Plc With Scada Enabled Reversible Drum Type Mixer/Concrete Batch Mix Plant (Pan Mixer) Etc. Complete. With Fine Aggregate (Crushed Sand Vsi Grade)
7	Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete.
8	Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.
9	Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per One Square Metre of vertical surface area covering 10 years guarantee on bond paper.
10	Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.
11	Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper.
12	Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
13	Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC without SCAD Aenabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
14	First Floor
15	Second Floor
16	Third Floor
17	Fourth Floor
18	Providing and laying Cast in situ/Ready Mixcement concrete M-35 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
19	First Floor
20	Second Floor
21	Third Floor
22	Fourth Floor
23	Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
24	First Floor
25	Second Floor
26	Third Floor
27	Fourth Floor
28	Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
29	Fourth Floor
30	Providing and laying Cast in situ/Ready Mix cement concrete in M-35 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
31	First Floor
32	Second Floor
33	Third Floor
34	Fourth Floor
35	Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite/granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
36	First Floor
37	Second Floor
38	Third Floor
39	Providing and laying in situ / ready mix M-35 cement concrete of trap /granite/quartzite/ gneiss metal for cast in citu R.C.C. solid piers,column etc . including provision of V shaped false joints to form suitable panels on the faces to approve design with compacting by vibrating and curing complete. Including plywood/steel formwork, centering ( excluding dewatering by means of pump) and including bailling out water and including CM 1:3 curing complete. ii) Height 5 to 7.50 m, add 5 percent extra over basic rate.
40	Providing and fixing during laying in RCC Slab rectangular 2 mm thick M.S. sheet fan hook box of size 180x100 mm with required depth with holes or notches as required, bottom and top sides of 1.6 mm M.S. sheet fixed with 3.5 mm dia. round headed screws together with 12 mm dia. M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface
41	First Floor
42	Second Floor
43	Third Floor
44	Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.
45	First Floor
46	Second Floor
47	Third Floor
48	Fourth Floor
49	Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.
50	Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete
51	First Floor
52	Second Floor
53	Third Floor
54	Fourth Floor
55	Providing Second class fly ash brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 mm diameter / two hoop iron strips 25 mm x 1.60 mm at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etc. complete.
56	First Floor
57	Second Floor
58	Third Floor
59	Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/ quartzite/ gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)
60	First Floor
61	Second Floor
62	Third Floor
63	Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.
64	First Floor
65	Second Floor
66	Third Floor
67	Fourth Floor
68	Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.
69	First Floor
70	Second Floor
71	Third Floor
72	Fourth Floor
73	Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 50 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both side, fixing in cement mortar 1:3 and curing etc. complete
74	First Floor
75	Second Floor
76	Third Floor
77	Fourth Floor
78	Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.
79	First Floor
80	Second Floor
81	Third Floor
82	Fourth Floor
83	Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 0x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P , scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
84	First Floor
85	Second Floor
86	Third Floor
87	Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.
88	First Floor
89	Second Floor
90	Third Floor
91	Supply, fixing and installation of 4mm thick Aluminium Composite Panel (ACP) of approved colour for external cladding in combination of solid and metallic colours, including all necessary Framework, support and complete weather sealing as per architectural drawing. The Aluminium Composite Panel (ACP) should be made out of thermoplastic core of low-density polyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets of ALLOY GRADE- 5000 series, each not less than 0.50 mm thick, total thickness of aluminium composite panels not to be less than 4 mm, the exposed surface thereof shall have Stove lacquered finishing coat not less than (26 + - 2) micron (containing minimum 70% kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface (facing the building exterior surface)shall have polyster based powder coating not less than 25 Micron with protective peel-off foil on the exterior face (peel off film will in no case leave any adhesive mark over the composite panel surface after it is peeled off). The supporting framework shall be made out of 50 mm X25mm X 3mm thick Aluminium section to be spaced horizontally and vertically for fixing of panel of size 900 mm X 1200 mm and fixed to the building structure as per design through 50mm X50mm X5 mm MS angle clamps prefixed to masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to be done with the help of VHB tapes and screws and all the sealing of joints to be done with weather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate)
92	First Floor
93	Second Floor
94	Third Floor
95	Fourth Floor
96	Providing and fixing SS-304 studs having 35mm dia. of the approved brand and make inside the building on all floors in corridors, lobbies level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer, using the necessary adhesive including finishing work up to the satisfaction of the engineer in charge complete.
97	First Floor
98	Second Floor
99	Third Floor
100	Directional signageDesign, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6\\" x 9\\" designed as per accessibility standards and having 4mm thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200mm from FFL and as per the directions by the engineer in charge.
101	Labour charges for providing groove in plaster having width and spaced as directed by engineer incharge etc. complete.
102	Fourth Floor
103	Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.
104	First Floor
105	Second Floor
106	Third Floor
107	Fourth Floor
108	Providing Water proofing treatment to newly laid fully cured concrete slab of terraces by applying first coat of polymer modified semi-viscous paste prepared by mixing polymer of approved make and Cement in 1 : 2 proportion ( 1 litre polymer : 2 Kg. Cement) to a neatly cleaned and dust free concrete surface and upto 300 mm. over parapet wall prepared by removing loose and deposited material with brush and water, laying glass fibre mesh of 10 x 10 specification of approved make over tacky surface of first coat of polymer followed by second coat in transverse direction, sprinkling coarse sand over it, followed by protective mechanical cover water proof plaster 20 mm thick after sufficient curing apply IPS 40 mm to 75 mm. thick cement concrete of 1:2:3 proportion using coarse aggregate of 10 MSA and water proofing compound of approved make and polypropylene fibres @ 125 gm per bag of cement making groovr 3 to 4 mm wide & 10 mm deep in concrete, in pannels of 3m/4m or as per site condition & filling the joints with poly sulphide sealant after curing including providing holler with drip moulds at the junction and finishing the concrete surface with neat cement slurry, as directed and ponding the surface as directed etc.complete ; covering 10 years guarantee against leakproofness on court Fee stamp paper of Rs 100/-
109	Third Floor
110	Fourth Floor
111	Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.
112	Second Floor
113	Third Floor
114	Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge)
115	Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.
116	First Floor
117	Second Floor
118	Third Floor
119	Fourth Floor
120	Providing and laying vitrified stone effect finish tiles having size 600 mm x 1200 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete
121	First Floor
122	Second Floor
123	Third Floor
124	Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.
125	First Floor
126	Second Floor
127	Third Floor
128	Providing and laying vitrified stone effect finish tiles having size 600 mm x 1200 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including required position laid on a bed of 1:4 cement mortarincluding neat cement float, filling joints, curign and cleaning etc. complete.
129	First Floor
130	Second Floor
131	Third Floor
132	Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.
133	Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 mm to 30 mm thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete.
134	Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, moulding edges,polishing,cleaning complete. b) Granite
135	First Floor
136	Second Floor
137	Third Floor
138	Fourth Floor
139	Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.
140	First Floor
141	Second Floor
142	Third Floor
143	Fourth Floor
144	Providing and laying vitrified rustic matt stone finish tiles having size 600 mm x 1200 mm of 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.
145	First Floor
146	Second Floor
147	Third Floor
148	Fourth Floor
149	Providing and laying vitrified rustic matt stone finish tiles having size 600 mm x 1200 mm of 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.
150	First Floor
151	Second Floor
152	Third Floor
153	Fourth Floor
154	Providing and laying telephone black/ Amba White/ Cadburybrown/ Ruby red/ Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.
155	First Floor
156	Second Floor
157	Third Floor
158	Fourth Floor
159	Providing and laying double charged vitrified matt fininsh tiles (antiskid) having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.
160	First Floor
161	Second Floor
162	Third Floor
163	Providing, laying and fixing exterior grade fibrilling fibre reinforcement heavy duty designer cement concrete tiles for Flooring of approved colour and design 22 +/ -2 mm thick bayer colour pigmented as per IS ..1237 - 1980 having compressive strength more than 500 Kilogram/sq.cm reaffirmed in 2006 ,having wert transvrse strenghth of 3.5 / mm 2, water absorption less than 10 % abrasion / wear resistance less than 2 mm ,skid resistance more than 25.0 (ASTM:E303) and no fading as per DIN - 51094 of size 300 x 300 in plan / designed pattern on a bed of 1:4 cement mortar including cement float ,filling joints with neat cement slurry ,curing, polishing and cleaning etc. complete. For flooring.
164	Providing and laying matt finish ceramic tiles of having size 30 cm x 30 cm confirming to I.S.15622/2006 (group D II-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. complete.
165	Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.
166	Providing and laying double charged vitrified matt finish tiles (antiskid) having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.
167	First Floor
168	Second Floor
169	Third Floor
170	Fourth Floor
171	Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)
172	First Floor
173	Second Floor
174	Third Floor
175	Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete
176	First Floor
177	Second Floor
178	Third Floor
179	Fourth Floor
180	Providing and fixing Country cut teak wood partly veneered and partly glazed partition with 75 mm x 50 mm frame at 60 cm center and 9 mm thick commercial ply on both sides, decorative veneer of 4 mm thick and plain glass 5 mm thick, including French polishing etc.complete
181	First Floor
182	Second Floor
183	Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.
184	First Floor
185	Second Floor
186	Third Floor
187	Fourth Floor
188	Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (With prior approval of S.E.)
189	First Floor
190	Second Floor
191	Third Floor
192	Fourth Floor
193	Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (including the primer coat)etc. complete.
194	First Floor
195	Second Floor
196	Third Floor
197	Fourth Floor
198	Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: ForItem One Number 15 to 18 prior approval of Superintending Engineer will be necessary
199	First Floor
200	Second Floor
201	Third Floor
202	Fourth Floor
203	Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.
204	Third Floor
205	Fourth Floor
206	Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from each other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.
207	First Floor
208	Second Floor
209	Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete
210	First Floor
211	Second Floor
212	Third Floor
213	Fourth Floor
214	Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: ForItem One Number 15 to 18 prior approval of Superintending Engineer will be necessary
215	Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35mm thick style and rail with 25 mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame)
216	First Floor
217	Second Floor
218	Third Floor
219	Fourth Floor
220	Solid Core Flush door Single leaf Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types, of exterior grade, as per detailed drawings, conforming to I.S.:2202 - 1962 (Revised) with approved face veneers on both faces with/without glazing and venetians in the positions shown on the drawings or as directed, all necessary beads, moulding and lipping, holdfasts, mat finish stainless steel fixtures fastenings , finishing with french-polish/ waxing complete. (without door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter
221	First Floor
222	Second Floor
223	Third Floor
224	Providing and Fixing 12mm thick toughened Glass openable door including S. S. pipe handle of 35mm size. High quality locking arrangement, door stopper, pivot of appropriate size, required hardware, All fittings and fixtures of Dorma company or equivalent including scaffolding, installation at site in groove of granite jam lining with transportation PVC tube and silicon etc all complete. Including cost of all material, fixtures, Carpenter, Skilled, Semiskilled helper, labour, transportation at site, open close signs etc. as directed by Engineer - In - Charge.
225	First Floor
226	Second Floor
227	Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.
228	First Floor
229	Second Floor
230	Third Floor
231	Fourth Floor
232	Providing and fixing of factory made uPVC casement window / Fixed Window & Casement Door (White Colour) comprising uPVC multi-chambered frame, Sash, & Mullion with wall thickness of 2.3mm (+-0.2 mm ), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name of the test Test Method Specified Parameter1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening Temperature EN ISO – 306 Shall not be < 750C3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m24 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm25 Mean Breaking Stress for welded corner(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2(b) For the compression bending test Shall not be < 30N/mm26 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %7 Surface Spread of flame BS : 476 - Part 7 Classification 18 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable9 Tensile modulus ASTM D 638 Shall not be < 35 MPa10 Shear Modulus ASTM D 732 Shall not be < 220 MPa11 Tensile Strength EN ISO 527 Shall not be < 30 MPa. All corners of frame and sash will be fusion welded. Mullion shall be welded / screwed. EPDM / TPE Gasket shall be provided in all frame, sash & mullion, wherever necessary.Thereafter, 5 mm Float Annealed glass shall be provided in the sash with the help of uPVC glazing bead and hardware, i.e., friction hinge & single point handle (in window) & 3D Hinges & Multipoint Lock (in door) shall be provided. Window / Door shall be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use.Fixed Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm.
233	First Floor
234	Second Floor
235	Third Floor
236	Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.
237	First Floor
238	Second Floor
239	Third Floor
240	Fire Door 45mm 1HR FRL (60/60) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR - Fire Door Tested in accordance to IS: 3614 Part 2.Providing 60 min Fire rated doors system duly tested for 3 criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 at National Test House, Govt of India laborator and/or with Central Building Research Institute, Govt of India undertaking with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology (\\"Non Combustible by Nature\\"). with prior approval of concerned Superitending Engineer.a) Door Frame: Supplying frames for Fire resistant door shutters 1st class Malaysian Hardwood Frame densified (810 Kilogram/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 60 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with single row of Brush- Type ASTROFLAME intumescent strip of size 10mm x 4mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete.
241	First Floor
242	Second Floor
243	Third Floor
244	Fourth Floor
245	Fire Door 45mm 1HR FRL (60/60) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR - Fire Door Tested in accordance to IS: 3614 Part 2.Providing 60 min Fire rated doors system duly tested for 3 criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 at National Test House, Govt of India laborator and/or with Central Building Research Institute, Govt of India undertaking with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology (\\"Non Combustible by Nature\\"). with prior approval of concerned Superitending Engineer.b)Shutter : Providing of 65mm thick asbestos free composite - 3 criteria - fire, heat and smoke check Accoustic Door Shutter with flame guard of 120 minutes IS3614 part -II comprising of 2x9mm Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 100x32 mm with 32mm thick infill of ceramic fiber (density 128Kilograms/CMT), vermaculite mix faced with 6mm Fire retardant High Density ply, internally lipped with hardwood beading, and pasted in Hydraulic Press under 50 tonnes pressure, spray quoted with 2 coats of In tumescent paint of minimum 200 micron, and with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed for fire and smoke sealing in the grooves in the shutter on all edges except bottom, without any external lipping.
246	First Floor
247	Second Floor
248	Third Floor
249	Fourth Floor
250	Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete
251	First Floor
252	Second Floor
253	Third Floor
254	Fourth Floor
255	Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete.
256	First Floor
257	Second Floor
258	Third Floor
259	Fourth Floor
260	Transportation of material obtained from debris of various sorts including necessary excavation/ loosing including loading, unloading and conveying and disposing as directed. ( Up to 10km)
261	Providing expansion joints with 25mm thick bituminous pad as per detailed drawings etc. complete.
262	Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
263	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
264	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
265	Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
266	Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.
267	First Floor
268	Second Floor
269	Third Floor
270	Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.
271	Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.
272	Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
273	Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete
274	Providing and casting in situ or precast tapering R.C.C. M-20 Semi Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface including painting with oil paint as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant
275	Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.
276	Providing and fixing informatory sign boards of size 0.90 x 0.60 m made out of 14 guage Aluminum sheet bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including on frame of with angle iron frame of size 35 x 35 x 5 mm and two M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in 1:4:8 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Alluminium sheet Type IV High Intensity Micro-Prismatic Grade Sheeting
277	Providing and fixing informatory sign boards of size 60 cm x 80 cm made out of 14 guage Aluminum sheet bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in 1:4:8 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Alluminium sheet Type IV High Intensity Micro-Prismatic Grade Sheeting
278	Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mm dia G.I. pipe ( Rezan/ concentiDeleted ire 0.75 mm dia ) with hot dip and G.I. coated hooks as per drawing supported on M.S. angle 50 x 50 x 6 mm at 2.5 mtr. c/c including fixing and fastening with wire, painting M.S. angles with one coat of red lead primer and two coat of oil paint etc. complete.
279	Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)
280	Providing and laying in situ / ready mix controlled grade of M25 of trap /granite /quartzite /gneiss metal for RCC works in cut off walls / curtain walls including necessary scaffolding, centering, compacting by vibrator, finishing and curing etc. complete. (with fully automatic micro processor based PLC with SCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with fine agreegates of required specifications ( VSI sand finely washed etc ), excluding reinforcement)
281	Providing, fixing and commissioning of Godrej or equivalent make APO Kareena high back chairSEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture.BACK SIZE: 48cm.(W) X 76.0cm.(H)SEAT SIZE: 51.0cm.(W) X 48.0cm.(D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps .KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism:The mechanism should be designed with the following features:• 360° revolving type single point control.• Front pivot for tilt with feet resting on ground ensuring more comfort.• Tilt tension adjustment.• 4-position locking with anti-shock feature.• Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positionsADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0±0.3cm.PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet . chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon.Overall Dimensions of ChairSeat Height - min 47.5 to max 57.5cm.Height - min 103.5 to max 120.5cm.Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.
282	First Floor
283	Third Floor
284	Providing, fixing and commissioning of Godrej or equivalent make APO Mingle modular table as per room sizeWork Surface-Made of 36mm thick MDFone side prelaminate board conforming to IS14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Full length access panel is provided with soft closing hinges inline with worktop edge. Worktop is available in various shapes.Understructure-The understructure consist of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together.Modesty-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Wire Management-An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout for Standard Anchor Roma 4 module is provided for electrical fittings in Straight two seater and single seater modules below access flap per seat.AV Details-The table is equipped with Extron cables cubbies along with cable retractors as standard offering only for 1800mm head module, 2350mm head module, 150° head module and 165° head module. For straight two seater and single seater modules, provision to mount AV cables is provided (eg. HDMI,VGAA, etc). Only Corner 90°, 30° corner and 50° corner modules have provision for wire flow between adjacent tables. Additional Wirecover made of 0.8mm Thick CRCA, provided below worktop to conceal MicroAV Detailsphone wires running from table top to wire tray.This product should be certified by GREENGUARD, Indoor Advantage GOLD, GRIHA & SVAGRIHA & GREEN PRO.
285	First Floor
286	Third Floor
287	Providing, fixing and commissioning of APO Kareena visitor back chairSEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture.MID BACK SIZE: 48.0cm.(W) X 64.5cm.(H)SEAT SIZE: 51.0cm.(W) X 48.0cm.(D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45±2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.ARMRESTS:The armrest top should be made of moulded polyurethane (P.U) and mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FIXED BACKREST: The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment.FIXED SPINE : The seat and backare arrested together withfixed type spine i.e no backup/down adjustment ;made of 0.8 ± 0.05cm thk HR steel ans id back power-coated (DFT 40-60 micros).TUBULAR VISITOR FRAME :The tubular frame is cantilever structure & made of Dia 2.54 ± 0.03cm. X 0.2±0.016cm.thk . M.S. E.R.W. tube with a M.S. Spine mounting bracket welded to it. Back spine is fitted to the assembly. The frame finish is Nickel Chrome plated (15-20 microns). Overall Dimensions of ChairSeat Height - 47.7cm.Height - 93.0cm.Width & Depth of Chair as measured from pedestal - Width-66.5 cm and Depth-61.6 cm
288	First Floor
289	Providing, Fixing and Commissioning of Godrej make APO Mayfair Main Desk size shall be 1200 Width x 600 Depth x 750 Height. The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT.The Modesty panel shall be in a combination of black & white cedar.
290	First Floor
291	Providing, supplying and commissioning of APO Pisa three seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.
292	Third Floor
293	providing, fixing and commissioning of godrej make APO reflection Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Access Flap along with a Gromett is provided on work surface for wire managementWire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width atAccess Flap position.Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lippingTOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.**Drawer bottom is made of 5.5thk MDF whiteboardHandle is provided for ease of opening.HDU and Drawer is provided with cam lock for security.Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management.Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes.Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging.This product should be certified by GREENGUARD & Indoor Advantage GOLD.
294	providing, fixing and commissioning of godrej make APO THRILL Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area.The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.The chair seat & back size areSEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression.ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:· 360° revolving type.· 3 position locking with anti shock mechanism.· Tilt tension adjustmentPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.WIDTH (W): 76.1 CM.DEPTH (D): 76.1 CM.HEIGHT (H): 101.5 - 111.0 CM.SEAT HEIGHT (SH): 44.5 - 54.0 CM.This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.
295	Third Floor
296	Providing, fixing and commissioning of Godrej or equivalent make APO granduar centre table of size 800 x 800 x 320 TOP AND BOTTOM PANEL:Made of 36mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneer lipping.SIDE PANEL:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Side panels are fitted with aluminum trim.SKIRTING:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping.
297	Third Floor
298	Providing, Fixing and Commissioning of Godrej or equivalent make APO premium lounge 3 seater SIDE FRAME ASSEMBLY: The side frame assembly should be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It should be made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cmx0.16cnn and black powder coated (DFT 40-60microns). The ends should be fitted with ABS moulded end caps.TIE MEMBER: It should be the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members should be used to connect the side frames. The tie-member should be of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cm x 0.16cm and black powder coated ( DFT 40-60 microns ). The seat/back assemblies should be mounted on one of the tie-member which has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5 ±0.1cm. thk -- 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back.SEATREST ASSEMBLY:The seat rest assembly consshould be ts of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 25 ± 2 kgf for 25% compression of the foam. The complete moulded seat rest assembly should be covered with a replaceable fabric upholstery coverSEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T)BACKREST ASSEMBLY:The backrest assembly should be flexing type and consshould be ts of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 14 ± 2 kgf for 25% compression of the foam. The complete moulded backrest assembly should be covered with a replaceable fabric upholstery cover.BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T)ADJ. GLIDES: The adj. glide should be injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take cshould be or unleveled floor surface.Overall Dimensions of Chair Seat Height - 43.5 cm.Height - 78.5cm.Width & Depth of Chair as - Width-164.0cm and Depth-70.0 cm.
299	providing, fixing and commissioning of godrej make coffee table, Overall Size : Width : 120cm Depth : 60cm Height : 36.7cm Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish : All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos
300	Providing and commissioning of Godrej or equivalent make APO majestic sofa Overall Size :1 Seater Width : 1060mm Depth : 840mm Height : 760mmUpholstery : Composite Leather. Pure Leather at touch points – seat and backrest andSyn Lth at non touch point matching with the pure leather• Leather Type : Pigmented• Syn Leather : PVC• Thickness of upholstery :Leather : 1 mmSyn Lth : 1 mm• ShadeCherry• Frame :Material - Solid wood frame with ply wood cross sectionMoisture Content : 12%• Foam Density :Seat : 28 kg/ cubic meter• Webbing : S spring• Legs : Rubber wood
301	Providing and commissioning of godrej make APO granduar side table of size 450 x 450 x 370 TOP AND BOTTOM PANEL:Made of 36mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneer lipping.SIDE PANEL:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Side panels are fitted with aluminum trim.SKIRTING:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping.
302	Providing, Fixing and Commissioning of Godrej make APO T Table - T 104 size shall be 1665 Width x 900 Depth x 750 Height . The top panels shall be made from 25 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be sq. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.
303	providing, fixing and commissioning of godrej make bravo visitore chair, SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressedplywood measured upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contouredlumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area.MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded withdensity = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS :The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame iscantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube.Overall Dimensions of ChairWIDTH (W): 61.4 CM.DEPTH (D): 64.5 CM.HEIGHT (H): 89.5 CM.SEAT HEIGHT (SH): 46.5 CM.This product should be certified by Indoor Advantage GOLD & GREEN PRO.
304	Providing, supplying and placing of Godrej or equivalent make Posture Perfect chair in premium napa laeather. SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.Seat SIZE: 45.5cm. (D) x 52.4cm. (W)BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D)ARMRESTS: The armrest having four range of adjustment· Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.· Up-Down adjustment has 8 position (10.5±0.5cm range)· Arm top swivel adjustment- 2 position, 12°±2° swivel inside· Arm top width adjustment - Any position (2.0±0.5cm range each arm top)· Arm top To - Fro Adjustment- any position (4.0±0.5cm range)· Armrest top is made up of high density PU molded over glass filled Poly-amide inner.POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following features:· 360° revolving type.· Forward tilt of sesat and back.· Upright tilt lock.· Tilt tension adjustment can be operated in seating position.· 3-position Tilt limiter.SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat depth adjustment range is of 5.0±0.5 cm.ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5±0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height adjustment has an adjustment stroke of 13.0±0.3 cm.PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia.TWIN WHEEL CASTOR: 5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.5±0.1cm wheel Diameter and assembled to pedestal.WIDTH (W): 74.0 CM.DEPTH (D): 74.0 CM.HEIGHT (H): 112.0 - 132.5 CM.SEAT HEIGHT (SH): 44.5 - 58.0 CM.This product should be certified by GREENGUARD GOLD & GREEN PRO.
305	Providing, fixing and commissioning of Godrej or equivalent make APO Kareena mid back chair SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture.BACK SIZE: 48cm.(W) X64.5cm.(H)SEAT SIZE: 51.0cm.(W) X 48.0cm.(D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps .KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism:The mechanism should be designed with the following features:• 360° revolving type single point control.• Front pivot for tilt with feet resting on ground ensuring more comfort.• Tilt tension adjustment.• 4-position locking with anti-shock feature.• Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positionsADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0 ±0.3cm.PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet ( should be : DD 1079 / HR skin pass ), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon.Overall Dimensions of ChairSeat Height - min 47.5 to max 57.5cm.Height - min 93.4 to max 110.4cm.Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.
306	Third Floor
307	Providing Fixing and commissioning of Godrej or equivalent make make Granduar table as per order 3000 x 1050 x 740 MAIN WORKTOP :Made of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping.LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface. Thisleather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board with top veneer face coated with clear lacquer. All thicknessedges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on topsurface.Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1)combination of MDF and particle board with top veneer face coated with clear lacquer. Allthickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB powerpoints, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.HIDDEN WIRELESS MOBILE CHARGER:It will only be available in 3000mm main table. It is fitted below leather pad.1500 x 600 x 610 ERU TOP PANEL:Made of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping. Top panel is provided with elliptical cable cover which contains 2 USBs, 1Universal socket, 1misc. cable grommet, 1 HDMI connector and 1 CAT-6 connector.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping.DOOR PANELS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door panels are provided with lock.ERU HEIGHT ADJUSTABLE LEG:The Leg consist of Outer and Inner Aluminum Extrusions (AL 63400 - WP). The Worksurface moves up & down due to the extension and compression of smooth functioninggas lift with adjustable height and consistent motion during operation. The gas lift isactuated using lever mechanism, operated manually.WORKTOP SUPPORT FRAME:The Worktop Support Frame consist of two 25.4x25.4x1.2mm thk ERW Tube (As per IS:7138) and Top support plate made of 2mm thk CRCA steel (As per IS: 513), weldedtogether. The gas lift is actuated using lever made of Dia 8 mm MS ROD (IS: 432) fromeither sides of the worktop.
308	Providing Installing and commisiioning of Godrej or equivalent make APO WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 932.5/1047/1200/1353/1467.50 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric magneitc/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic/fabric/laminated/prelam. SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric magnetic/fabric tackable/white board/prelam/ plain metal along with split fabric magnetic/fabric tackable/white board/prelam/ plain metal. INTERMEDIATE BLOCKS Intermediate blocks are given in fabric/DL + Fabric/DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. HALF SCREEN WITH FRAME - at intermediate position between 2 people and at the end above worktop in clear glass/fabric tackble /laminate/white board finsh. Side panels or legs - out of 25 mm thk prelam particle board with flat pvc lipping edge banding considered only on the open end conditions or metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding This product should be certified by GREENGUARD, Indoor Advantage GOLD, BIFMA LEVEL 2 & GREEN PRO
309	Second Floor
310	Third Floor
311	Providing, Fixing and Commissioning of Godrej or equivalent make APO pisa 2 seater SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.Width (W): 146.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.
312	Third Floor
313	providing, supplying and commissioning of Sotrwel plain M2 model storage unit. Product Size:916mm(W) x 486mm(D) x 1980mm(H).Construction & Material:Welded construction. 0.7mm thk CRCA for shelf. 0.8mm thk CRCA for back & locker shelf .0.8mm thk HSCR for doors .0.9mm thk CRCA for all other components .Locking & handle, Mazak handle , Three way locking mechanism with shooting bolt .Locker:Fixed full locker with secret compartment.Hinged Door:2 way locking mechanism for locker door .Shelving: Height wise adjustable shelf mounting .2Nos. of adjustable full Shelf .Hanging Rod & Tie bar:1.0mm thk ERW tube for hanging rod . 1.0mm thk aluminum for tie bar .Leveler:M10 screw type leveler with hex plastic base .Finish:Epoxy Powder coated to the thickness of 50 microns (+-10).This product should be certified by GREEN PRO.
314	Providing, Fixing and Commissioning of Godrej or equivalent make APO Storwel Minor plain shall have an overall size of 765mm(W)x440mm(D)x1270mm(H) with welded construction. It should have the shelf thickness of 0.7mm, Back thickness of 0.8mm and all other components shall be 0.9mm thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513. The storwel Minor should have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).
315	Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.
316	Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources)
317	Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - II Material
318	Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.
319	Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.
320	Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement with max 20% fly Ash ( Fly-ash upto 20% by weight of Cement) over a prepared sub base with 43 grade cement , coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.
321	Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 gms per sqm using surface roller and protecting from falling dust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1 :8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )
322	Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mm dia. 70 cms.long and at 30.00 cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening , supported by assembly of TMT FE 500, chairs with proper alignment etc. complete.
323	Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.
324	Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/ colour of 2.5 mm thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/ lux and Qd of 100 mcd/sqm/ lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015).
325	Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer.
326	Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
327	Providing cast in situ / ready mix M20 grade cement concrete for head walls of CD work / retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA
328	Providing and laying in situ / ready mix M-20 controlled cement concrete of trap/ granite/ quartzite/ gneiss metal for RCC work in solid/ deck slab etc. including ramming, vibrating, curing, formwork, centering and finishing in cement plaster excluding reinforcement etc. complete. (with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer and fine agreegates of required specifications ( VSI sand finely washed etc ) i) Height up to 5 m, normal rate.
329	Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.
330	Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.
331	Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 600mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.
332	Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete.
333	First Floor
334	Second Floor
335	Third Floor
336	Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make with P.V.C. waste pipe with fitting arrangement etc.complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)
337	First Floor
338	Second Floor
339	Third Floor
340	Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge.
341	First Floor
342	Second Floor
343	Third Floor
344	Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.
345	Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.
346	First Floor
347	Second Floor
348	Third Floor
349	Providing and fixing 15 mm diameter PVC Aqua kraft type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete
350	First Floor
351	Second Floor
352	Third Floor
353	Providing and fixing C.P. sink cock with raised J\\" shaped swinging casted spout ofapproved make including necessary sockets/ union nut etc. complete.\\"
354	First Floor
355	Second Floor
356	Third Floor
357	Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.
358	First Floor
359	Second Floor
360	Third Floor
361	Grab bars-Providing SS grab bars set for accessible toilets comprising of 4 nos. Grab bars as specified below.(1 nos. wing grab bar + 1 nos. L shaped grab bar + 2 nos. straight grab bars = 1 typical set) 27a) Swing grab bar (1 NOS) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 NOS) Providing S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM (D) and 32MM DIA. and thickness mm of the approved brand and make. 27c) Straight grab bar (2 NOS) Providing S.STEEL 304 GRAB RAIL (600 MM),32MM DIA. and thickness 1.5mm of the approved brand and make.
362	First Floor
363	Second Floor
364	Third Floor
365	Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.
366	First Floor
367	Second Floor
368	Third Floor
369	Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete
370	First Floor
371	Second Floor
372	Third Floor
373	Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)
374	First Floor
375	Second Floor
376	Third Floor
377	Providing and fixing 8 cm rigid PVC Nahani trap including PVC grating ,bend, connecting piece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)
378	First Floor
379	Second Floor
380	Third Floor
381	Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.
382	First Floor
383	Second Floor
384	Third Floor
385	Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
386	First Floor
387	Second Floor
388	Third Floor
389	Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
390	First Floor
391	Second Floor
392	Third Floor
393	Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
394	First Floor
395	Second Floor
396	Third Floor
397	Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
398	Fourth Floor
399	Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.
400	First Floor
401	Second Floor
402	Third Floor
403	Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.
404	Fourth Floor
405	Providing and fixing screw down for 40 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.
406	Fourth Floor
407	Providing , laying and fixing ,jointing Eco- drain 160 mm SN 4 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees , coupler, etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated materialetc. complete.
408	Providing , laying and fixing ,jointing Eco- drain 200 mm SN 4 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees tees, coupler etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated materialetc. complete.
409	Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.
410	Providing , constructing and fixing 600 mm dia. Inspection chamber made up of Polypropylene / polyethylene material Having 315 mm diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160 mm and 200 mm pipes having thickness of 5 mm and 600 mm in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5 mm having R.C.C. cover and frame fixing in 150 mm thick in c.c.1:2:4, having crushed sand bed of 150 mm thick of size 750 mm dia. Including excavation and refilling the sides of chamber by ?sand crushed cushioning 150 mm thickness, connecting all required UPVC fittings with rubber lubricant etc.complete.
411	Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75Kilogramwith lid and frame fixed in cement concrete.
412	Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75Kilogramwith lid and frame fixed in cement concrete.
413	Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.
414	Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.
415	RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge
416	Providing and fixing 40mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangements and lock. [Withoutchamber].
417	Providing and laying in trenches 32 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
418	Providing and laying in trenches 40mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
419	Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151/ 12786 / 13488 with nesessary jointing material like mechanical connector i.ethread / insert joint /quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials,including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOMin all respect etc.complete.Note:- H.D.P.E. Pipes shall be as per latest IS Specifications Also HDPE pipes upto 110 mm Dia.shall be in coil form.PE 100 PN10 KG/SQ.CM. GRADE 75MM DIA PIPE
420	Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. Please Enable Macros to View BoQ information
421	Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Maharashtra Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Building Including Electrification For Technology And Energy Park In The Premises Of Rtm Nagpur University At Nagpur, Nagpur-Maharashtra

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Building Including Electrification For Technology And Energy Park In The Premises Of Rtm Nagpur University At Nagpur, Nagpur-Maharashtra

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us