Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/ Or Residential Complex At Dudhichua Area For 3 Months(Nit No : Dch/So(C)/25-26/Etn-55 Date: 21.03.2026), Sonbhadra-Uttar Pradesh

TDR : 54780429

Tender Notice
BOQ

14 Days Left

Sonbhadra , Uttar Pradesh

Tender Brief : Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/ Or Residential Complex At Dudhichua Area For 3 Months(Nit No : Dch/So(C)/25-26/Etn-55 Date: 21.03.2026)

Document Fees
Refer document

EMD
₹ 269600.0 /-

Tender Value
₹ 2.15 Crore /-

Submission Date
07-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil
3	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).
4	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)
5	12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
6	Neat cement punning
7	Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mmnominal size).
8	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Cold twisted bars
9	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete
10	Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:6 (1cement : 6 coarse sand)
11	Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm Area of slab over 0.50 sqm.
12	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.
13	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
14	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m. All kinds of soil.
15	CARRIAGE OF MATERIALS Carriage of material by Mechanical Transport including loading, unloading and stackingLime, moorum, building rubbish Lead - 1 Km
16	French spirit polishing : Two or more coats on new works including a coat of wood filler.
17	Providing and fixing 100 mm sand cast Iron grating for gully trap.
18	Providing and fixing PTMT grating of appropved quality and colour circular type 100 mm nominal dia
19	Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :100 mm dia pipe
20	Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm
21	Providing and fixing Stainless Steel A Isis 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460 mm bowl depth 200 mm.
22	Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm.
23	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
24	Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.
25	Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : Black solid plastic seat with lid
26	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.
27	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
28	Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729.
29	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 100 mm dia pipe
30	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm diaSand cast iron S&S as per IS - 1729
31	Providing and fixing plain bend of required degree.100 mm diaSand cast iron S&S as per IS - 1729
32	Providing and fixing heel rest sanitary bend100 mm diaSand cast iron S&S as per IS - 1729
33	Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100 mmSand cast iron S&S as per IS - 1729
34	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand Cast Iron S&S as per IS: 1729
35	Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm diameter
36	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
37	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 110 mm diameter
38	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm
39	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend
40	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe
41	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
42	Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm
43	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm
44	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm
45	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm
46	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm
47	Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 150 mm
48	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm
49	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 75x47x1.70 mm
50	Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complet 250x16 mm
51	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm
52	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm
53	Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm
54	Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100 mm
55	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper
56	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper
57	Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws
58	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type)
59	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm.
60	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 5.5 mm .
61	Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
62	Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws.
63	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 30 mm thick shutters. with ISI marked M.S. pressed butt hinges bright finished of required size - Kiln seasoned and chemically treated hollock wood.
64	Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete. With12 mm mild steel U beading
65	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Kiln seasoned and chemically treated hollock wood. 30 mm thick shutters
66	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Kiln seasoned and chemically treated hollock wood.
67	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Particle Board 12 mm thick Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS: 3087 marked
68	Painting top of roofs with bitumen of approved quality @ 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG - 10
69	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces.
70	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete
71	Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick
72	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia. & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood
73	Supplying and fixing new wooden fillets wherever necessary: Hollock wood fillets.
74	Renewal of old putty of glass panes (length) .
75	Lettering with black Japan paint of approved brand and manufacture
76	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
77	Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. In cement mortar
78	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metres and below
79	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below
80	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
81	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm
82	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
83	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
84	Supplying and spreading of stone dust including watering, rolling and proper consolidation layer by layer as per instruction of EIC
85	Finishing walls with water proofing cement paint of required shade : Old work (one or more coats @ 2.20 kg/10 sqm) complete.
86	Distempering with 1st quality acrylic distember (Ready mix) having VOC contentless than 50 grams/ litre of approved brand and manufacture to give an even shade:specification.
87	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.
88	White washing with lime to give an even shade : Old work (one or more coats) .
89	Providing and fixing to existing door frames. 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (±0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.
90	Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm).
91	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
92	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
93	Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work.
94	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
95	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm) with necessary accessories and screws etc. complete.
96	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.
97	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore
98	Brick Work with non modular fly as(FLAG) confirming to ISI 12894 of class designated 7.5 average compressive strength etc. complete in all respect in foundation and plinth in cement mortar 1:6(1cement:6coarse sand)
99	Brick Work with non modular fly as(FLAG) confirming to ISI 12894 of class designated 7.5 average compressive strength etc. complete in all respect in superstructure above plinth level upto floor V level in cement mortar 1:6 (1cement:6coarse sand )
100	Half Brick Work with non modular FLAG) bricks confirming to ISI 12894 of class designated 7.5 average compressive strength etc. complete in all respect in foundation and plinth In cement mortar 1:4 (1cement:4coarse sand )
101	Half brick Work with non modular fly FLAG brick confirming to ISI 12894 of class designated 7.5 average compressive strength etc. complete in all respect in superstructure above plinth level upto floor V level in cement mortar 1:4 (1cement:4coarse sand )
102	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).
103	Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers
104	6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
105	Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster
106	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
107	Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.
108	Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
109	Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers
110	Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.
111	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.
112	Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100 mm : and sand cast iron S&S as per IS - 1729
113	Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 100 mm : Sand cast iron S&S as per IS - 1729
114	Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
115	Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
116	Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.
117	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
118	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes\
119	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material Beyond 30 cm girth upto and including 60 cm girth
120	Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.
121	Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size)as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade.
122	Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore
123	Providing and fixing paper holder with flap recessed type of Jaquar make or equivilent.
124	Providing and fixing bowl for coupled wc with pp soft close seat cover, hinges, fixing accessories set size 375 x 650 x 770 mm with cistern and fittings of jaquar make or equivilent.
125	Providing and fixing hand shower of jaquar make or equivilent.
126	Providing and fixing hung wash basin with fixing accessories set size 560x470x195 mm of Jaquar make or equivilent.
127	Providing and fixing swivel towel holder twin type of jaquar make or equivilent.
128	Providing and fixing angular stop cock with wall flange of jaquar make or equivilent.
129	Providing and fixing two way bib cock with wall flange of jaquar make or equivilent.
130	Providing and fixing soap dispensor with glass bottle of jaquar make or equivilent.
131	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil Extra rates for quantities executed in and under water including pumping out water
132	Welding by gas or electric plant including transportation of plant at site etc. complete.
133	Easing and adjusting of rolling shutter
134	Making old existing shutter with taking down shutter and repair damaged members by wooden planks which is available by old taking down shutter and fixing in frame etc. including necessaty nails,screws etc
135	Cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand :4 graded stone aggregate) finished with a floating coat of neat cement,including cement slurry but excluding the cost of nosing of steps etc complete. 25 mm thick with 12.5 mm nominal size stone aggregate
136	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. One coat.
137	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.
138	Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: White glazed fire clay kitchen sink of size 600x450x250 mm.
139	Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. Overall width 35 mm.
140	Facility Manager (Highly skilled) (One no. per day)
141	Assistant Facility Manager (Avg skilled + Highly skilled) (4 nos. per day)
142	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
143	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness
144	Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-incharge. With stainless steel cover plate minimum 1.25 mm thickness
145	Providing and laying matt finished vitrified tile of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such asfootpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. (Item No. 16.89)
146	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
147	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm
148	Trimming of tree branches in colony/plant &near boundary wall including disposal of branches outside of periphry of the colony &plant Area as per instruction of EIC.
149	Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately) :-Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire (Item No. 16.18.1)
150	Petty carpentary repair works such as repairing of cupboard, nails screw fixing hinges tightening of doors and windows shutter etc. as & when required as per instruction of EIC.
151	Small petty water supply related works
152	Small petty mason repair works such as patches on wall, hole repair etc.
153	Providing round the clock security guard without gun for watch &ward of Government premises and its all belongings by deploying neatly dressed security guards in 8 hour's shift including necessary T&P like torch, lathi and uniform etc.complete,as per directions of Engineer-in-charge.(One job means 8 hour's duty). In case of any theft, dounle of stolen amount will be recovered.
154	Providing round the clock security guard with gun for watch & ward of Government premises and its all belongings by deploying neatly dressed security guards in 8 hour's shift including necessary T&P like torch, lathi and uniform etc.complete,as per directions of Engineer-in-charge.(One job means 8 hour's duty).In case of any theft, dounle of stolen amount will be recovered.
155	Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.\\"
156	Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
157	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
158	Dozing, leveling and dressing of the dump sites with help of Mechanical Hydraulic Excavator along with driver, fuel & any other Sundries item complete, as directed by Engineer-in-charge
159	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 100 mm dia pipe
160	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 150 mm dia pipe
161	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 200 mm dia pipe
162	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm dia Class I
163	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm dia Class I
164	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 200 mm dia Class I
165	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 250 mm dia Class I
166	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 300 mm dia Class I
167	Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class) : Up to 300 mm dia
168	Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 20 mm nominal bore
169	Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore
170	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : 15 mm dia nominal bore
171	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : 20 mm dia nominal bore
172	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : 20 mm dia nominal bore
173	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : 25 mm dia nominal bore
174	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : 40 mm dia nominal bore
175	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : 50 mm dia nominal bore
176	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : 80 mm dia nominal bore
177	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore
178	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore
179	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.
180	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore
181	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore
182	Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket : 150 mm dia pipes
183	Supplying pig lead at site of work.
184	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 100 mm diameter pipe
185	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 150 mm diameter pipe
186	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 200 mm diameter pipe
187	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 250 mm diameter pipe
188	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 300 mm diameter pipe
189	Providing and fixing brass stop cock of approved quality : 15 mm nominal bore
190	Providing and fixing brass stop cock of approved quality : 20 mm nominal bore
191	Providing and fixing brass bib cock of approved quality : 15 mm nominal bore
192	Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length : 15 mm nominal bore
193	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 : 15 mm nominal bore
194	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore
195	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore
196	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : Flexible pipe : 32 mm dia
197	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : Flexible pipe : 40 mm dia
198	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore
199	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore
200	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore
201	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore
202	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm nominal bore
203	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular Tank
204	Providing and fixing PTMT bib cock of approved quality and colour. : 15mm nominal bore, 86 mm long, weighing not less than 88 gms
205	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore
206	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore
207	Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. : 10 litre capacity - White
208	Providing and fixing bolts including nuts and washers complete.
209	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.: 20 mm nominal outer dia Pipes
210	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter
211	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. : 15 mm nominal bore, 105 mm long, weighing not less than 138 gms
212	Providing and fixing PTMT pillar cock of approved quality and colour : 15 mm nominal bore, 107 mm long foam flow, weighing not less than 110 gms
213	Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour : Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
214	Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour : waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
215	Providing and fixing PTMT, push cock of approved quality and colour : 15 mm nominal bore, 98 mm long, weighing not less than 75 gms
216	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 15 mm
217	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 20 mm
218	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 25 mm
219	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 40 mm
220	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 50 mm
221	Fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 80 mm
222	Providing and fixing of 15mm CP brass pillar tap
223	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore
224	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : Above 40 mm nominal bore
225	Supply of bib cock washer
226	Supplying of GI Socket : 15 mm dia
227	Supplying of GI Socket : 20 mm dia
228	Supplying of GI Socket : 25 mm dia
229	Supplying of GI elbow : 15 mm dia
230	Supplying of GI elbow : 20 mm dia
231	Supplying of GI elbow : 25 mm dia
232	Supplying of GI Nipple : 15 mm dia
233	Supplying of GI Nipple : 20 mm dia
234	Supplying of GI Nipple : 25 mm dia
235	Supplying of GI Tee : 15 mm dia
236	Supplying of GI Tee : 20 mm dia
237	Supplying of GI Tee : 25 mm dia
238	Supplying of GI Plug : 15 mm dia
239	Supplying of GI Plug : 20 mm dia
240	Supplying of GI Plug : 25 mm dia
241	Supplying of GI Plug : 40 mm dia
242	Supply of PVC WATER tank cover
243	Supply of float valve for L.L. Cistern
244	Supply of syphon for L.L. Cistern
245	Supply of syphon washer for Cistern
246	Supply of handle for L.L. Cistern
247	Supply of jumper washer
248	Providing steel spindle with checknut : 100 mm dia
249	Providing steel spindle with checknut : 150 mm dia
250	Supply of gland packing
251	Supply of M- Seal
252	Supply of rubber packing
253	Cleaning of roof top water tank, including draining out water, cleaning, disinfecting the tank, by bleaching power etc. and washing the tanks with fresh water, writing of cleaning date with paint on the outer face of the tank all complete with tools, tackles and consumables as per instruction of EIC
254	Repairing of sluice valve spindle
255	Lowering and lifting of Indian mark - II hand pump as per instruction of EIC
256	Providing and fixing plunger of Indian mark II lower and upper side complete set for one hand pump etc. all complete as per instruction of EIC
257	Providing and fixing chain for hand pump etc. all complete as per instruction of the EIC
258	Providing and fixing centre pin for Indian make hand pumps
259	Providing and fixing washer for Indian make hand pumps
260	Providing and fixing GI pipes of 32 mm dia with Indian make hand pumps etc. all complete as per instruction of the EIC 32 mm dia Class B
261	Proviidng and fixing GI socket long type thread for using lowering . 32 mm dia GI Pipe with pump 32 mm dia
262	Providing and fixing new cylinder of Indian Mark II hand pump
263	Providing and fixing big rod for hand pump
264	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall : 20 mm nominal outer dia. Pipes.
265	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall : 25 mm nominal outer dia .Pipes.
266	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall : 40 mm nominal outer dia .Pipes.
267	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore
268	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
269	Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore, Horizontal
270	Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms
271	Providing and fixing PTMT stop cock of approved quality and colour. 20 mm nominal bore, 89 mm long, weighing not less than 88 gms
272	Providing and fixing 15 mm C.P. brass pillartaps,
273	Providing and Fixing CP brass Waste : 32 mm dia
274	Providing and Fixing CP brass Waste : 40 mm dia
275	Providing and Fixing G.I. plung : 20 mm dia
276	Providing and Fixing G.I. plung : 25 mm dia
277	Providing and Fixing G.I. sluce valve 80 mm
278	G.I socket : 80 mm dia
279	Supply of G.I bend 80 mm
280	Supply of G.I. Flange : 100 mm dia
281	Supply of G.I. Flange : 80 mm dia
282	Operation of valve and pump in sector A, B&C colony by deploying 17 number manpower. Penal recovery of double of payment of manpower will be made for not deploying labour on any given day.
283	Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, includinghire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
284	Providing & fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL, 50 mm dia nominal bore
285	Providing liquid chlorine solution , Sodium Hypochlorite(5% Concentration) based formulated conforming to IS-11673:1993 Grade-1 and10500-1991 for treatment of potable water
286	Clearing of residential OH Tank as per instruction of EIC (Two times in 2 years)
287	cleaning of ground water reservoir including scrapping of stains and muck from wall and floor and removal o muck from reservoir, disinfecting the tank with fresh water, writing the cleaning datye with paint on the outer surface of the tank all complete with tools, tackle and comsumaables as per instruction of EIC
288	Proving and fixing of pump shaft (steel)
289	Proving and fixing of shaft sleeve (bronze)
290	Proving and fixing of set of key
291	Proving and fixing of gland packing (3 times in a year)
292	Proving and fixing of coupling set
293	Proving and fixing of coupling bolt
294	Proving and fixing of rubber bush
295	Proving and fixing of impeller 1st stage (bronze)
296	Proving and fixing of impeller 2nd stage (bronze) make kirloskar
297	Proving and fixing of inter stage ring bronze make-kirloskar
298	Proving and fixing of bearing cover
299	Proving and fixing of bearing cap
300	Proving and fixing of shaft sleeve nut (bronze)
301	Proving and fixing of set of gasket
302	Proving and fixing of bearing 6307 (for 100-36 pump) make-SKF
303	Proving and fixing of bearing 3307 (for 100-36 pump) make-SKF
304	Proving and fixing of power contactor 3 pole,110 amp, 440 volt, make L&T
305	Proving and fixing of power contractor 3 pole,70 amp, 440 volt, make L&T
306	Proving and fixing of 3 PH, make L&T
307	Proving and fixing of CTS interposing, single 20
308	Proving and fixing of indicating lamp with holding lamps
309	Proving and fixing of push button actuator with contact block 1NO+1NC
310	Proving and fixing of Fuse base and carrier
311	Proving and fixing of Fuse link 6 amp
312	Proving and fixing of voltmeter 96 sq mm
313	Proving and fixing of ameter 96 sq mm
314	Switch ameter voltmeter selector
315	PVC Control cable 2.5 sq mm in meters
316	PVC copper cable 16 sq mm flexible in meters
317	copper lug 16 sq mm
318	stud type terminal
319	Repairing/ Rewinding of 3 phase 30 Kwatt, 415 V ac induction motor (Minimum Six months warrenty after repair/rewinding work)
320	Repairing/ Rewinding of 3 phase 37 Kwatt, 415 V ac induction motor (Minimum Six months warrenty after repair/rewinding work)
321	Repairing/ Rewinding of 3 phase 55 Kwatt, 415 V ac induction motor (Minimum Six months warrenty after repair/rewinding work)
322	Proving and fixing of bearing 6309 (for 22 KW) make-SKF
323	Proving and fixing of bearing 6310 (for 22 KW) make-SKF
324	Proving and fixing of bearing 6311 (for 30 KW & 37 KW) make-SKF
325	Proving and fixing of bearing 6312 (for 30 KW & 37 KW) make-SKF
326	Proving and fixing of bearing 6314 (for 55 KW ) make-SKF
327	Proving and fixing of bearing NU (for 55 KW ) make-SKF
328	greece for pump/motor (Kg)
329	Repairing of shaft of bearing position both side
330	Repairing of bearing housing
331	Dismentling of pump including handling loading transporting and unloading from site to workshop as per requirement
332	General schedule and periodic checking of pump including greacing, servicing and complete over hauling of pump as required engineer incharger(once in a month 12*10 nos)
333	Handling, loading, transporting with installation testing and commisioning of repaired pump and motorfrom workshop to site
334	Repairing of shaft at bearing position for motor
335	General schedule and periodic checking of motor and starter including greacing, servicing and complete over hauling of motor as required engineer incharger(once in a month 12*10 nos)
336	REPAIRING AND MAINTENANCE OF MOTOR AND PUMP UPTO 25 HP INCLUDING DISMENTLING AND RESETING IN POSITION AFTER REWINDING AND OVERHAULING AS PER INSTRUCTION OF EIC, OLD COPPER WIRE WINDING TO BE RETURNED TO THE DEPARTMENT (Including lifting & lowering as per instruction of EIC) ( Minimum warrenty of 6 months after repair)
337	PROVIDING AND FIXING SUBMERSIBLE PUMPS AND MOTORS INCLUDING SUITABLE CONTROL PANEL WITH ALL ACCESSORIES FITINGS AND FIXING AND COMMISSIONING ETC. SUPPLY AND INSTALLATION OF SUBMERSIBLE PUMPS(KSB/TAXMO OR APPROVED EQUIVALENT) FOR ONE NO OF BOREWELL(CAPACITY 3000 GPH) AND HEAD UPTO 120 METER DEPENDING ON YIELD AS PER INSTRUCTION OF EIC (Including lifting & lowering as per instruction of EIC)
338	PROVIDING AND FIXING PVC FLAT CABLE WITH FITTINGS AND FIXING SUITABLE FOR COMMISSIONING SUPPLY AND INSTALLATION OF COPPER BASED 6 sqmm FLAT CABLE REQUIRED FOR 1 NO PUMP SET AS PER INSTRUCTION OF EIC
339	Cleaning of toilet (Floor area upto 10 Sqm) including cleaning of dado, skirting, WC pan (Indian type/western type), wash basin, urinals, glass shelves, mirror and other fittings, if any for D type or equivalent Qtrs. including any other wash basin outside the toilet by hand dusting and cleaning with soap solution acids, deodorants, phenyl etc.to make the toilet clean & hygienic all complete with tools, tackles & consumables as per instruction of EIC.
340	Cleaning of toilet (Floor area upto 8 Sqm) including cleaning of dado, skirting, WC pan (Indian type/western type), wash basin, urinals, glass shelves, mirror and other fittings, if any for \\"C\\" type or equivalent Qtrs. including any other wash basin outside the toilet by hand dusting and cleaning with soap solution acids, deodorants, phenyl etc.to make the toilet clean & hygienic all complete with tools, tackles & consumables as per instruction of EIC.
341	Cleaning of toilet including WC pan, wash basin, other fittings, if any for \\"B\\" & lower type Quarter by hand dusting and cleaning with soap solution acids & phenyl etc.to make the toilet clean & hygienic all complete with tools, tackles as per instruction of EIC.
342	Cleaning of toilet with attached with hostel room, office chambers etc including cleaning of floors, skirting and dado, WC pan (Indian/European type ) wash basin, shelves, mirror and other fittings ,if any, by hand dusting and cleaning with soap solution acids, deodorants , phenyl etc to make the toilet clean andhygienic and providing naphthalene balls in urinals complete with all tools,tackles and consumable as per instruction of EIC (For community and service buildings)
343	Cleaning mopping and washing of floor of public buildings and other places neatly with detergent/ bleaching powder etc. all completes with tools tackles and consumable to make the floor clean and hygienic as per instruction of EIC.
344	Cleaning of surface drain including disposal of muck/sludge through trolley or other arrangement to a specified place(in no case it shall be kept on drain banks) within a lead of 1Km complete with all tools & tackles as per instruction of EIC : Upto 300 mm wide
345	Cleaning of surface drain including disposal of muck/sludge through trolley or other arrangement to a specified place(in no case it shall be kept on drain banks) within a lead of 1Km complete with all tools & tackles as per instruction of EIC : Above 300 mm up to 600 mm
346	Cleaning of surface drain including disposal of muck/sludge through trolley or other arrangement to a specified place(in no case it shall be kept on drain banks) within a lead of 1Km complete with all tools & tackles as per instruction of EIC : Above 600 mm
347	Collection of garbage from door to door and disposal of the same through closed Door to door collection vehicle enabled with GPS system for tracking to the specified place within lead of 1KM and time duration of 4 hours per day(8 AM to 12 Noon)including sweeping of stair case(for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC. : Ground floor
348	Collection of garbage from door to door and disposal of the same through closed Door to door collection vehicle enabled with GPS system for tracking to the specified place within lead of 1KM and time duration of 4 hours per day(8 AM to 12 Noon)including sweeping of stair case(for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC.: First Floor
349	Collection of garbage from door to door and disposal of the same through closed Door to door collection vehicle enabled with GPS system for tracking to the specified place within lead of 1KM and time duration of 4 hours per day(8 AM to 12 Noon)including sweeping of stair case(for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC. : Second Floor
350	Brooming & cleaning of all roads in colony and within the premises of service building and other places as required with all tools & tackles and stacking the garbage at specified place as per instruction of EIC.
351	Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into pit with adequate quantity of salt, lime bleaching power etc. and refilling the pit with earth all complete with tools, tackles and consumables as per instruction of EIC : Big animal (Cow,Buffalo,OX and the like)
352	Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into pit with adequate quantity of salt, lime bleaching power etc. and refilling the pit with earth all complete with tools, tackles and consumables as per instruction of EIC : Small animal (Dog,Cat,fox,pig,birds and the like)
353	Cleaning of sludge line and traps(Kitchen & toilets) of all diameters at different floors including opening of joints, cleaning of pipe line and again jointing & flushing with fresh water all complete with tools and tackles as per instruction of EIC.
354	Transportation of solid waste to centralised SLRM center Niaghi or as per instructions of EIC from Sector A, Lead 4 Km
355	Transportation of solid waste to centralised SLRM center Niaghi or as per instructions of EIC from Sector A, Lead 2 Km
356	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
357	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
358	Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.1 Screened through sieve of I.S. designation 20 mm
359	Rough dressing the trenched ground including breaking clods.
360	Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
361	Grassing with selection No. 1 grass including watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and earth shall be paid for separately). In rows 5 cm apart in both directions
362	Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 60 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (The manure/sludge shall be paid for separately).
363	Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm
364	Filling of the following size empty pots with mixture of good earth & manure in the ratio of 2:1 (Two part of Good earth & one port of manure) and placing them on appropriate place i/c carriage of earth, manure and pots up to 50 mtr, as per direction of officer incharge. (The cost of good earth, earthen pots & manure will be paid separately.) Size of Empty Pots 35cm Top dia, 25cm Bottom Dia & 35cm Perpendicular height.
365	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste out side of the peripheri of colony, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) : Prestigious works / H.M. house & officers entitled to free accommodation.(as per yard stick 1Mali =1.00Acre)
366	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste out side of the peripheri of colony, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) : Play grounds / Public parks (as per yard stick 1Mali =2.00Acre).
367	Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.
368	Maintenance of potted plants Cement pots at ground floor in flats and ground floor bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required (Materials shall be provided by the department) as per direction of officer in charge
369	Maintenance of potted plant Earthen pot in displayed at ground floor only in bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required ( Materials shall be provided by the department) as per direction of officer in charge
370	Providing and wartering of plants through water tanker of Horticulture features i.e. tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge.
371	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) : Trees Plant
372	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) : Shrubs Plant
373	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) : Hedge Plant/Ground Cover
374	Providing and displaying of Araucaria cookie plant, having ht. 60 cm to 75 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 20 cm size of Earthen pot / Plastic pot. & as per direction of the officer-in-charge.
375	Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.
376	Providing and displaying of Croton Baby Golden Punctatumaureum plant, having ht. 23 cm to 30 cm, well developed with fresh and healthy foliage in 15 cm size of Earthen pot / Plastic pot. as per direction of the officer-incharge.
377	Providing and Displaying plants Dahlia double kenya variety in different colour well developed with 3 to 4 flowers in half bloom, good foliage stacked with Green painted Bamboo sticks, 45 to 60 cm height in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
378	Providing and Displaying plants Dahlia single in different colour with fresh & healthy foliage well developed with 6 to 8 half blooming buds in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
379	Providing and Displaying plants Gerbera Hybrid, well developed, with fresh and healthy foliage, fully blooms in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
380	Providing and Displaying plants Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
381	Providing and Displaying plants Marigold(Tagetes) inca hybrid different colour having 30 cm and above ht., with 6 to 8 flowers in bloom & blooming condition, well developed pot should be fully covered with fresh and healthy, foliage and flowers in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
382	Providing and Displaying plants Pansy hybrid sakata in different colour with fresh & healthy foliage well developed in 15 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
383	Providing and Displaying plants Salvia dwarf variety with fresh & healthy foliage well developed multi branching in blooming stage in 15 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
384	Providing and Displaying plants Verbena in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
385	Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.
386	Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.
387	Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.
388	Bone meal
389	Rose mixture
390	Neem cake
391	Sarso khali
392	Super phasphate
393	Folidal
394	Melatian
395	Roger30%
396	Monocrotophas
397	Man co Jeb
398	Indocell
399	Supply and stacking of Phyllanthus emblica (Amla) plant of height 150 to 165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
400	Supply and stacking of Eugenia jambolana (Jamun) plant of height 150 to 165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
401	Supply and stacking of Mangifera indica (Mango-grafted ) plant of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-incharge.
402	Supply at site good quality pots: Earthen pots of size 12\\" size
403	Painting of flower pots as per instruction of EIC :Earthen pots of size 12\\" Wall masta/Terracota
404	Painting of flower pots as per instruction of EIC : Cement concrete pots of size 15\\" with synthetic enamel paint
405	Providing Plant Chrysenthamum (Guldowdi) single variety in different colour well developed having 45 to 60 cm ht., minimum 100 and above half bloom flowers open well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 25 cm Earthen Pot
406	Providing and Displaying plants Petunia hybrid in different colour with fresh & healthy foliage well developed in 15 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.
407	Supplying & Stacking of Selection No.1 Grass at site fresh & free from weeds havingproper roots in green including loading, unloading, carriage and all taxes paid etc.andas per direction of officer in charge
408	Anti adult measures:-General disinfection/pest control with new generation odourless, colourless insecticides which should be safe for human being and effective for all kind of house hold insects like mosquitos, house flies, etc. using Residual spray of Deltamethrin 2.5% SC Flow (K-othrine or approved equivalent) insecticides should be sprayed uniformly over the surfaces of walls, ceilings, etc.Frequency- Once in 3 months
409	Thermal fogging Using insecticide deltamethrin 1.25% ULV(King fog or approved equivalent) mixed with diesel in the ratio of 1:199, for outdoor operation of colony etc.Frequency - Monthly
410	Anti Larvae Measures: -Treatment by using Diflubenzuron 25% WP(Bi - Larv or approved equivalent ) solution to be spread as per instruction of EICFrequency - Weekly
411	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermitetreatment (excluding the cost of chemical emulsion) :Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mmdia holes at downward angle of 45 degree at 150 mm centre to centre and sealingthe same.
412	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermitetreatment (excluding the cost of chemical emulsion) :Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cementWith Chlorpyriphos/Lindane E.C. 20% with 1% concentrationmortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :
413	Removing and uprooting of unwanted Vegetation grown over the drainage pipes, walls,chhajjas, balcony and similar locaton of building upto floor Vth level with all tools & plantsrequired with safety precautions and making good the same with plaster including disposal ofmaterial / tree roots etc. at the required place all complete as per instruction of EIC.
414	Providing manpower for attending power failures in individual residential quarters, administrative buildings, and residential blocks including leakage current fault clearance in Sector ‘A’, Sector ‘B & C’, and GM Office to ensure smooth and uninterrupted operation of township on 24x7 basis. The work includes deployment of 08 skilled and 08 unskilled personnel for maintaining the above work.Note : The rate is inclusive of contractor profit, Tools and Tackles and exclusive of CMPF/EPF and CMPS etc.)
415	Supplying and fixing of 4X4 PVC plain board
416	Supplying and fixing of 7X4 PVC plain board
417	Supplying and fixing of 8X6 PVC plain board
418	Supplying and fixing of 8X10 PVC plain board
419	Supply of 3mm thick phenolic laminated sheet
420	supply of Iron scews, 35mm X 6mm
421	supply of Iron scews, 40mm X 6mm
422	supply of Iron scews, 45mm X 6mm
423	supply of PVC fastener 40mm long
424	supply of PVC clip for fixing cable
425	supply of 32mm X 8mm bolts & nuts
426	supply of 38mm X 10mm bolts & nuts
427	Wiring for circuit/submain wiring along with earth wire with the 2X2.5 sq.mm +1X2.5 sq.mm earth wire of FRLS PVC insulated copper conductor single core cable In surface/recessed medium class PVC conduit as required.
428	Wiring for circuit/submain wiring alongwith earth wire with the 2X4 sq.mm +1X4 sq.mm earth wire of FRLS PVC insulated copper conductor single core cable In surface/recessed medium class PVC conduit as required.
429	Wiring for circuit/submain wiring along with earth wire with the 2X10 sq.mm +1X6 sq.mm earth wire of FRLS PVC insulated copper conductor single core cable In surface/recessed medium class PVC conduit as required.
430	wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch ,modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required.
431	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 3 pin 5/6 modular socket outlet and 5/6 amps modular switch, connection etc. as required.
432	Supplying and fixing suitable size GI box with modular plate and cover in FRLSont on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
433	Wiring for light point/fan point/exhaust fan point/call bell point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable In surface/recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
434	Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in FRLSont including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.
435	Supplying and fixing of 5/6 amps piano type switch on the existing switch box/cover including connections etc. as required.
436	Supplying and fixing 3 pin 5/6 amps piano type socket on the existing switch box/cover including connections etc. as required.
437	Supplying and fixing bell push piano type switch/socket on the existing switch box/cover including connections etc. as required.
438	Supplying and fixing of 15/16 amps piano type switch on the existing switch box/cover including connections etc. as required.
439	Supplying and fixing 6 pin 15/16 amps piano type socket on the existing switch box/cover including connections etc. as required.
440	Supplying and fixing PVC batten/angle holder including connections etc. as required.
441	Supplying and fixing 3 pin, 5 amp ceiling rose on the exisiting junction box/wooden block connection etc. as required.
442	Supplying and fixing of 2.5μf capacitor (SAP Material code - 4600016871)
443	Supplying and fixing of electronic fan regulator (SAP Material code - 4600016856)
444	Supplying and fixing 63A , four pole,415 V, 3 phase and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required.
445	supplying and fixing 5A to 32 apms rating, 240/415 volt, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required
446	supplying and fixing 5A to 32 apms rating, 240/415 volt, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of single pole and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required
447	Supplying and fixing 40A , double pole,(single phase and neutral) 240 V,residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
448	Supplying and fixing 63A , double pole,(single phase and neutral) 240 V,residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
449	Supplying and fixing 63A , four pole,(three phase and neutral) 415 V,residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
450	Providing and fixing 100 A capacity TPN disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc as required.
451	supplying and fixing 20 A, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve,SP,MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.
452	Supplying and fixing 6 way Double door, single pole and neutral, sheet steel, MCB distribution board,240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/isolator)
453	Supplying and fixing 8 way Double door, single pole and neutral, sheet steel, MCB distribution board,240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/isolator)
454	Supplying and fixing 12 way Double door, single pole and neutral, sheet steel, MCB distribution board,240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/isolator)
455	Providing and fixing 100A, 30KA,FPMCCB and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubic panel board including drilling holes in cubicle panel, making connections, etc. as required.
456	Providing and fixing 250A, 36KA,FPMCCB and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubic panel board including drilling holes in cubicle panel, making connections, etc. as required.
457	Complete rewinding of ceiling/exhaust fans including changing of all defective parts like shaft, bearings, winding,capacitors, clamps, rubber bush, etc as required with dismantling,cleaning, transportation and fixing (only bearing and condensers will be provided by NCL and other items shall be supplied by contractor) (material and labour cost)
458	Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required
459	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep
460	Supply, Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service V9 (CM/M/) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tole:. as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
461	Supply and fixing of call bell/ buzzer suitable fo single phase 230 Volts complete as required
462	Supply and fixing of ceiling fan bearing of required size
463	Supplying and fixing of exhaust fans having sweep size of 300 mm (SAP Material code - 4600015880)
464	supply and fixing of 3 pin electric plug (top) 5 A
465	supply and fixing of 3 pin electric plug (top) 15 A
466	Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of upto 35 sq mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
467	Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of upto 35 sq mm (clamped with 1mm thick saddle) on wall surface as required.
468	Errection of all aluminium conductor of 7/1.96 mm to 7/3.10 mm diameter including binding etc. as required.
469	Checking & replacement of LV/MV pin/shackle insulator etc. as required.
470	Checking & replacement of disc/ pin insulator 11KV/ 6.6 KV over head lines as required.
471	Erection of all type of LED street light fittings or shed-mounted fittings, including lead extension connections (if required), connection of surge arresters, tightening, and minor repair of fittings, etc., as per the instructions of the Engineer-in-Charge (E&M/TS).
472	Checking and re-jumpering work of service connection cables (from overhead line to buildings) and main cables (from substation to overhead line) as required. The scope also includes cleaning and re-jumpering of street light fittings of any type and make by connecting the cable leads of fittings to the overhead line conductor
473	Jungle clearance including cutting and removal of tree branches and roots obstructing the 33KV overhead line (up to 5 metres on both sides from the centre line) and the 6.6KV overhead line (cutting and removal of trees from both sides and disposal from the root level).
474	Fault clearing due to lightning/raining season/strom etc as required (fault of overhead line are fault of cable etc.)(02 Nos. unskilled & 01 no. skilled)(labour charge only) as & when required basis and any time as per instruction of engineer in charge(E&M/TS)
475	Cleaning washing of floor neatly and removal by tools and tackles of different sub-stations (33KV/6.6KV main substation, B type s/s, M type s/s, D type s/s & sector A s/s) in the township for this work 01 no. unskilled man power required per day Please Enable Macros to View BoQ information
476	Cleaning washing of floor neatly and removal by tools and tackles of different sub-stations (33KV/6.6KV main substation, B type s/s, M type s/s, D type s/s & sector A s/s) in the township for this work 01 no. unskilled man power required per day Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Services Tenders

Hospitality Related Services Tenders

Facility Management Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/ Or Residential Complex At Dudhichua Area For 3 Months(Nit No : Dch/So(C)/25-26/Etn-55 Date: 21.03.2026), Sonbhadra-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/ Or Residential Complex At Dudhichua Area For 3 Months(Nit No : Dch/So(C)/25-26/Etn-55 Date: 21.03.2026), Sonbhadra-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us