|
| 1 | Sub-Head : Earth Work |
| 2 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Sub-Head : Concrete Work |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Sub-Head : Masonry Work |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 8 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | Sub-Head : Wood and P.V.C. Work |
| 10 | Deduct for not providing hinges in doors, windows or clerestory window shutters with : |
| 11 | ISI marked Stainless steel butt hinges with stainless steel screws : |
| 12 | For 2nd class teak wood and other class of wood shutters |
| 13 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 14 | 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws |
| 15 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 16 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 17 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : |
| 18 | 30 mm thick shutters |
| 19 | with ISI marked M.S. pressed butt hinges bright finished of required size - Kiln seasoned and chemically treated hollock wood |
| 20 | Providing and fixing good quality drapery rod chromium plated M.S. pipe minimum 1.25mm thick to be fixed on the side and intermediate brackets (Brackets will be paid separately) : |
| 21 | 25 mm dia (heavy type) |
| 22 | Providing and fixing good quality chromium plated side and internediate brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete. |
| 23 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) |
| 24 | 300x16 mm |
| 25 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 26 | 200x10 mm |
| 27 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 28 | 300x16 mm |
| 29 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 30 | 100 mm |
| 31 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 32 | Twin rubber stopper |
| 33 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. |
| 34 | Double strip (horizontal type) |
| 35 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.50 mm all complete. |
| 36 | With 2nd class teak wood beading 62X19 mm. |
| 37 | Sub-Head : Steel Work |
| 38 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 39 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 40 | Arranging welding machine for welding of Broken steel componants such as Handels, fastners, hinges, grills, etc.as and where required as per the direction of Engineer-in-Charge. (rate includes labour & transportation of machine at site). |
| 41 | Sub-Head : Flooring |
| 42 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 43 | Sub-Head : Roofing |
| 44 | Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : |
| 45 | 100 mm diameter |
| 46 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 47 | (i)Single socketed pipes. |
| 48 | 75 mm diameter |
| 49 | 110 mm diameter |
| 50 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 51 | Single tee with door |
| 52 | 75x75x75 mm |
| 53 | 110x110x110 mm |
| 54 | Bend 87.5° |
| 55 | 75 mm bend |
| 56 | 110 mm bend |
| 57 | Shoe (Plain) |
| 58 | 75 mm Shoe |
| 59 | 110 mm Shoe |
| 60 | Sub-Head : Finishing |
| 61 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 62 | Two or more coats on new work. |
| 63 | Sub-Head : Repairs to Buildings |
| 64 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. |
| 65 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 66 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 67 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 68 | Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm). |
| 69 | Renewal of old putty of glass panes (length) . |
| 70 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) |
| 71 | Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. |
| 72 | Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial de-silting of manholes and de-chocking of sewer lines. De-chocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth. |
| 73 | Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- |
| 74 | (i) Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits. |
| 75 | (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. |
| 76 | (iii) Chlorination of RCC internal surface by liquid chlorine. |
| 77 | (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. |
| 78 | (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge. |
| 79 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \\"S\\" or \\"P\\" trap including dismantling of old WC seat and \\"S\\" or \\"P\\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
| 80 | Orissa pattern W.C Pan of size 580x440 mm |
| 81 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 82 | Removing & refixing Aluminium door shutter with frame for smooth operation including taking out door with frame, dismembering aluminium door sections, taking out panelling, reassembling the door shutter with aluminium cleats with screws, rivets & refixing the available panelling in position with snap beading & fixing the shutter in position with necessary stainless steel hinges with rivets or pivots with necessary screws etc complete as directed by the Engineer In charge. |
| 83 | Of area upto 2.00 Sqm |
| 84 | Supply of a labour for miscellaneous civil maintenance works in T.E and staff quarters compound as and when required by E.IN. C , such as uprooting vegitation ,leveling the earth, cleaning the roots khurras, gully trap minor urgent civil works whenever required all complete as per direction of engineer -in - charge (The item included all labour, T&P required) |
| 85 | Cleaning of drainage manholes and sewer lines by removing the deposited and other rubbish from the manholes and cleaning the sewer lines by rodding and flushing with water as directed by the Engineer -in- charge. (Rate per One manhole and sewer line to next manhole) |
| 86 | Attending repairs to Low level PVC flush tanks by replacing necessary parts as per requirement as directed. |
| 87 | Removal of deposited sludge from Septic tank by diluting the sludge with plenty of water and using a Mechanical hydraulic suction machine, pumping, vaccum cleaning and removing all the waste liquid and sludge from the septic tank and disposing the waste at Municipal dumping ground. The rate includes all machinery and workmen required and all incidental charges during pumping, filling, transporting etc complete as directed by the Engineer-in-charge. |
| 88 | Sub-Head : Dismantling and Demolishing |
| 89 | Dismantling of flushing cistern of all types (C.I./PVC/Vitreous China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 90 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 91 | Credit for: |
| 92 | Unserviciable GI Pipes/Fiitings |
| 93 | Unserviciable Brass Bib/stop cocks/pillar tap |
| 94 | Sub-Head : Sanitary Installations |
| 95 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : |
| 96 | W.C. pan with ISI marked white solid plastic seat and lid |
| 97 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 98 | Kitchen sink without drain board |
| 99 | 610x510 mm bowl depth 200 mm. |
| 100 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 101 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 102 | 10 litre capacity - White |
| 103 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 104 | White solid plastic seat with lid |
| 105 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 106 | Flat back wash basin of size 550x400 mm. |
| 107 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 108 | Semi rigid pipe |
| 109 | 32 mm dia |
| 110 | Flexible pipe |
| 111 | 32 mm dia |
| 112 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 113 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 114 | Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. |
| 115 | Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms. |
| 116 | Sub-Head : Water Supply |
| 117 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 118 | 15 mm nominal outer dia. Pipes. |
| 119 | 20 mm nominal outer dia. Pipes. |
| 120 | 25 mm nominal outer dia .Pipes. |
| 121 | 32 mm nominal outer dia. Pipes. |
| 122 | Providing and fixing CPVC ball valve of approved make for CPVC pipe lines. |
| 123 | 25mm size |
| 124 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 125 | 45 cm length |
| 126 | 15 mm nominal bore |
| 127 | Providing and fixing CPVC unions for CPVC pipe line including cutting and fixing. |
| 128 | for 25mm dia pipe line |
| 129 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 130 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: |
| 131 | 15 mm nominal bore. |
| 132 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 133 | 15 mm nominal bore |
| 134 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : |
| 135 | 15mm nominal bore |
| 136 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 137 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 138 | Providing and fixing PTMT pillar cock (u shaped high neck) of approved quality and colour . |
| 139 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 140 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 141 | 15 mm nominal bore, 105 mm long. Weighing not less than 138 gms. |
| 142 | 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. |
| 143 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 144 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. |
| 145 | 20mm nominal bore. Weighing not less than 40 gms. |
| 146 | Providing and fixing covers for PVC water storage tanks with necessary MS/PVC clamps. |
| 147 | (a) For 500 litres capacity tanks |
| 148 | Sub-Head : Conservation of Heritage Buildings |
| 149 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. |
| 150 | The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. |
| 151 | Note :- (1) The elevational area of the scaffolding shall be measured for payment purpose. |
| 152 | (2) The payment will be made once only for execution of all items for such works. Please Enable Macros to View BoQ information |
