|
| 1 | Surface dressing of the ground including removing vegetation andinequalities not exceeding 15 cm deep and disposal of rubbish, leadup to 50 m and lift up to 1.5 m All kinds of soil |
| 2 | Excavation work by mechanical means (Hydraulic excavator)/ manualmeans in foundation trenches or drains (not exceeding 1.5m in widthor 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary roc |
| 3 | Excavation work by mechanical means (Hydraulic excavator)/ manualmeans in foundation trenches or drains (not exceeding 1.5m in widthor 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soils as directed, within a lead of 50 m.Hard rock (blasting prohibited) |
| 4 | Providing and laying in position cement concrete 1:4:8 (1 Cement :4 coarse sand : 8 graded stone aggregate 40 mm nominal size).of specified grade -All work upto plinth level excluding the cost ofcentring and shuttering |
| 5 | Providing and laying in position specified grade of reinforced cementconcrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20 mm nominal size) - All work upto plinth level excludingthe cost of centring, shuttering, finishing and reinforcement |
| 6 | Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) upto floor five levelwork in walls (any thickness), including attached pilasters, buttresses,plinth and string courses, fillets, columns, pillars, piers,abutments,posts and struts etc. excluding cost of centring, shuttering, finishingand reinforcement |
| 7 | Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases aboveplinth level up to floor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5coarse sand(zone-III) derived from natural sources : 3 graded stoneaggregate 20 mm nominal size derived from natural sources). |
| 8 | Reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete Cold twistedbars. by the direction in Engineer -Thermo-Mechanically Treated barsof grade Fe-500D or more. |
| 9 | Centering and shuttering including strutting, propping etc. and removalof form foFoundations, footings, bases of columns, etc. for mass concrete |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for FORM WORK .Columns, Pillars, Piers, Abutments, Posts and Struts |
| 11 | Centering and shuttering including strutting, propping etc. and removalof form forLintels, beams, plinth beams, girders, bressumers and cantilevers |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform |
| 13 | Centering and shuttering including strutting, propping etc. and removalof form for Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc. |
| 14 | Providing and fixing tie bolt, spring coil and plastic cone in wallshuttering complete as per the direction of Engineer-in-charge. 20 mmdia.& 225 mm length |
| 15 | Brick work with F.P.S. bricks of class designation 75 in superstructureabove plinth level upto floor V level in all shapes and sizes in Cementmortar 1:6 (1 cement : 6 coarse sand) |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular)bricks of class designation 7.5 in superstructure above plinth level upto floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 17 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars atevery third course of half brick masonry. |
| 18 | 15 mm cement plaster on rough side of single or half brick wall ofmix.1:6 (1 cement : 6 fine sand) |
| 19 | 12 mm cement plaster of mix.1:6 (1 cement : 6 fine sand) |
| 20 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand ) |
| 21 | Providing and fixing T-iron frames for doors, windows and ventilatorsof mild steel Tee-sections, joints mitred and welded, including fixing ofnecessary butt hinges and screws and applying a priming coat ofapproved steel primer. Fixing with 15x3 mm lugs 10 cm longembedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominalsize). |
| 22 | Providing and fixing 35 mm thick ISI marked flush door shuttersconforming to IS: 2202 (Part I) non-decorative type, core of blockboard construction with frame of 1st class hard wood and wellmatched commercial 3 ply veneering with vertical grains or crossbands and face veneers on both faces of shutters.including ISImarked Stainless Steel butt hinges with necessary screws. |
| 23 | Providing and fixing factory made ISI marked steel glazed doors,windows and ventilators, side /top /centre hung, with beading and allmembers such as F7D,F4B, K11 B and K12 B etc. complete ofstandard rolled steel sections, joints mitred and flash butt welded andsash bars tenoned and riveted, including providing and fixing ofhinges, pivots, priming coat of approved steel primer, but excluding thecost of other fittings,glass panes complete all as per approved design,(sectional weight of only steel members shall be measured forpayment).Fixing with 15x3 mm lugs 10 cm long embedded in cementconcrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) |
| 24 | Providing and fixing M.S. grills of required pattern in frames ofwindows etc. with M.S. flats, square or round bars etc. includingpriming coat with approved steel primer all complete. Fixed to steelwindows by welding |
| 25 | Providing and fixing fly proof galvanized M.S. wire gauge to windowsand clerestory windows using wire gauge with average width ofaperture 1.4 mm in both directions with wire of dia 0.63 mm allcomplete. With 12 mm mild steel U beading |
| 26 | Providing & fixing glass panes with putty and glazing clips in steeldoors, windows, clerestory windows, all complete with : 4.0 mm thickglass panes |
| 27 | Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent ordyed to required colour or shade, with necessary screws etc. complete: 125 mm |
| 28 | Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per IS : 1868 )transparent or dyed to required colour or shade, with necessaryscrews etc. complete :100x10 mm |
| 29 | Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessaryscrews etc. complete. Single rubber stopper |
| 30 | Providing and fixing PTMT door catcher of length 72 mm and dia. of42 mm with suitable washers weighing not less than 33 gms |
| 31 | Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS 15622 (thickness to be specified by the manufacturer), of approvedmake,in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers ofsteps and dados,over 12 mm thick bed of cement mortar 1:3 (1cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm, including pointing in white cement mixed with pigment ofmatching shade complete |
| 32 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st qualityconforming to IS : 15622 of approved make in colours such as White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4(1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matchingpigment etc., complete |
| 33 | 62 mm thick cement concrete flooring with concrete hardener topping,under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 graded stone aggregate 20 mm nominal size) and top layer12 mm thick cement hardener consisting of mix 1:2 (1 cementhardener mix : 2 graded stone aggregate, 6 mm nominal size) byvolume, hardening compound mixed @ 2 litre per 50 kg of cement oras per manufacture’s specifications. This includes cost of cementslurry, but excluding the cost of nosing of steps etc. complete. |
| 34 | Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade :New work (two or morecoats) over and including water tinnable priming coat with cementprimer |
| 35 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. |
| 36 | Finishing walls with Acrylic Smooth exterior paint of requiredshade13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 37 | Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50grams/ litre of approved brand and manufacture, including applyingadditional coats wherever required to achieve even shade and colour. |
| 38 | Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade : Two or morecoats on new work over an under coat of suitable shade with ordinarypaint of approved brand and manufacture |
| 39 | Providing and fixing hand rail of approved size by welding etc. to steelladder railing, balcony railing, staircase railing and similar works,including applying priming coat of approved steel primer M.S. tube |
| 40 | Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with seal ringconforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes 110 mm diameter |
| 41 | Providing and fixing water closet squatting pan (Indian type W.C. pan )with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manually controlled device(handle lever) conforming to IS : 7231, with all fittings and fixturescomplete, including cutting and making good the walls and floorswherever required: White Vitreous china Orissa pattern W.C. pan ofsize 580x440 mm with integral type foot rests |
| 42 | Providing and fixing white vitreous china pedestal type water closet(European type) with seat and lid, 10 litre low level white vitreouschina flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard makeand mosquito proof coupling of approved municipal design complete,including painting of fittings and brackets, cutting and making good thewalls and floors wherever required :W.C. pan with ISI marked whitesolid plastic seat and lid |
| 43 | Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm and 340x410x265 mmsizes respectively with automatic flushing cistern with standard flushpipe and C.P. brass spreaders with brass unions and G.I clampscomplete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required : One urinal basinwith 5 litre white P.V.C. automatic flushing cistern |
| 44 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: White Vitreous China Wash basin size 630x450 mmwith a single 15 mm C.P. brass pillar tap |
| 45 | Providing and fixing white vitreous china laboratory sink with C.I.brackets, C.P. brass chain with rubber plug, 40 mm C.P brass wasteand 40 mm C.P. brass trap with necessary C.P. brass unionscomplete, including painting of fittings and brackets, cutting andmaking good the wall wherever required : Size 450x300x150 mm |
| 46 | Providing and fixing soil, waste and vent pipes : 100 mm diaCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:3989 |
| 47 | Providing and fixing soil, waste and vent pipes : 75 mm diaCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS:3990 |
| 48 | Providing and fixing plain bend of required degree. 100 mm dia Sandcast iron S&S as per IS : 3989 |
| 49 | Providing and fixing plain bend of required degree. 75 mm dia Sandcast iron S&S as per IS : 3990 |
| 50 | Providing and fixing collar : 100 mm Sand cast iron S&S as per IS -3989 |
| 51 | Providing and fixing single equal plain invert branch of required degree: 100x100x100 mm Sand cast iron S&S as per iron 1729 |
| 52 | Providing and fixing single equal plain invert branch of required degree: 75x75x75 mm Sand cast iron S&S as per iron 1729 |
| 53 | Providing and fixing single unequal junction of required degree withaccess door, insertion rubber washer 3 mm thick, bolts and nutscomplete : 100x100x75 mm Sand cast iron S&S as per IS - 3989 |
| 54 | Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete. |
| 55 | Providing and fixing terminal guard :100 mm Sand cast iron S&S asper IS - 3989 |
| 56 | Providing and fixing trap of self cleansing design with screwed downor hinged grating with or without vent arm complete, including cost ofcutting and making good the walls and floors : 100 mm inlet and 75mm outlet Sand cast iron S&S as per IS - 3989 |
| 57 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun)iron pipes and fittings of diameter : 100 mm |
| 58 | Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 100 mm |
| 59 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. 15 mm dia nominal bore |
| 60 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. 25 mm dia nominal bore |
| 61 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. 50 mm dia nominal bore |
| 62 | Providing and fixing ball valve (brass) of approved quality, High or lowpressure, with plastic floats complete 15mm nominal bore |
| 63 | Providing and fixing gun metal non- return valve of approved quality(screwed end) : 25 mm nominal bore Horizontal |
| 64 | Providing and fixing uplasticised PVC connection pipe with brassunions : 45 cm length 20 mm nominal bore |
| 65 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. Rectangulartank. |
| 66 | Providing and fixing brass bib cock of approved quality : 15 mmnominal bore |
| 67 | Providing and fixing C.P. brass long body bib cock of approved qualityconforming to IS standards and weighing not less than 690 gms. 15mm nominal bore |
| 68 | Providing and fixing PTMT pillar cock of approved quality andcolour.15 mm nominal bore, 125 mm long foam flow, weighing not lessthan 120 gms |
| 69 | Providing and fixing C.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931. 15 mm nominalbore |
| 70 | Providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS:8931 15 mm nominal bore |
| 71 | Providing and fixing PTMT soap Dish Holder having length of 138 mm,breadth 102 mm, height of 75 mm with concealed fitting arrangements,weighing not less than 106 gms |
| 72 | Providing and fixing PTMT swivelling shower, 15 mm nominal bore,weighing not less than 40 gms |
| 73 | Providing and fixing PTMT towel rail complete with brackets fixed towooden cleats with CP brass screws with concealed fittingsarrangement of approved quality and colour. 450 mm long towel railwith total length of 495 mm, 78 mm wide and effective height of 88mm, weighing not less than 170 gms |
| 74 | Providing and fixing toilet paper holder : C.P. brass |
| 75 | Excavation in Hilly Areas in Ordinary Rock by mechanical means notrequiring blasting (With out Dozer) Excavation in hilly area in ordinaryrock not requiring blasting by mechanical means without using Dozerincluding cutting and trimming of slopes and disposal of cut materialwith a lift upto 1.5 m and lead upto 20 m as per Clause 1603.2. |
| 76 | Excavation in foundation for retaining, breast walls etc, in all types ofsoils and rocks including all lead, lift and disposal of surplus materialas per direction of engineer - in - charge, as per drawing and technicalspecifications Clause 305.1 of MORD Specifiction |
| 77 | Removal of Unsuitable Soil with Disposal upto 1000 m Removal ofunsuitable soil including excavation, loading and disposal upto 1000 mlead but excluding compaction ground supporting embankmentsubgrade replacement by suitable soil, which shall be paid separatelyas per Clause 303.5.2 as per Technical Specification Clause 302.3.11 |
| 78 | Concrete with cement, coarse sand and 40 mm gauge stone ballast inproportion 1:4:8 in foundations and floors including supply of allmaterial, labour and T&P etc. required for proper completion of thework. as per drawings and technical specifications Clause 802, 803,1202 & 1203 |
| 79 | Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, inbreast walls, retaining walls, parapets, scuppers, etc. including supplyof all material, labour, T&P and royaltiies etc. complete as per drawingand technical specifications Clauses 702, 704, 1202 & 1203 of MORDSpecifiction |
| 80 | Hand Packed stone filling in back of wallls including cost of allmaterials,royality, T&P etc. complete as per direction of Engineer-incharge. (As per PWD Uttarakhand specifications) |
| 81 | Cement plum Masonry with 40% plum & 60% 1:3:6 cement concreteincluding supply of all material, labour, T&P etc. required for propercompletion of the work. as per drawings and technical specificationsClause 802, 803, 1202 & 1203 of MORD Specifiction |
| 82 | Providing and Laying of Mechanically Woven Double TwistedHexagonal shaped Gabions of galvanized steel, of size 3mX1mX1mwith two diaphragms at 1m interval, having mesh opening 100mmx120mm, mesh wire diameter 3 mm for gabions, edge/selvedge wirediameter 3.9 mm and lacing wire diameter 2.2 mm. (The work includesfilling boulders in the gabions) Please Enable Macros to View BoQ information |
