|
| 1 | Stripping and stacking iron sheets of a roof including ridging, flashing, eaves boards gutters and down pipes. |
| 2 | Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. Doors of area 3 sqm and below. |
| 3 | Windows of area 3 sqm and below |
| 4 | Scraping White wash and colour wash |
| 5 | HOISTING, ROOFING AND WATER PROOFING Corrugated G.I. Sheet roofing 0.80 mm thick fixed with galvanized iron J or L hooks 10mm dia, G.I. Limpot and bitumen washers complete excluding the cost of purling rafters and trusses |
| 6 | Providing and Fixing ceiling at height upto 4 mtr consisting of 12.5mm thick Gypsum Board of any size G.I. Cradling hanged from the ceiling by means of G.I. hanger complete as per drawings,specifications and tothe entire satisfaction of engineer-in- charge. |
| 7 | Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16 |
| 8 | Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3 |
| 9 | Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. |
| 10 | providing and fixing on wall face unplasticised Rigid PVC rain water pipes single socketed (working pressure 4 kgf / cm²) conforming to IS : 4985, including fixing with MS clamps. U-PVC pipes (working pressure 4 kgf. / sqcm) pipe 110 mm dia. |
| 11 | Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend |
| 12 | Water proofing of roof terraces, Basements, Retaining Walls, Water tanks etc with Zydex Zycoprime / Elastobar / Equivalent solution so as to form a water-resistant cementitious bonding coat and to form on-site seamless cross-linked elastomeric membrane on the concrete surface to reduce its porosity. Creating a cementitious elastomeric polymeric membrane of Elastobar and Zycoprime/Equivalent after application of Zycosil & Zycoprime Solution in New Construction. Take equal parts of Elastobar and Cement and form a paste. Add little water to the paste to make it brushable. Apply the paste on surface with brush. Leave the surace for drying for at least 4 - 6 hours to get elastomeric membrane. After this application, make one more layer of rough cementatios membrane using mixture of 1 Part of Zycoprime + 1 Part of Cement + 1 Part of fine sand. Apply paste on the surface with a brush to make a rough texture. Now your surface is ready to bond well with tiles/screed. |
| 13 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.60 mm (+ 0.05 %) thick |
| 14 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish |
| 15 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 16 | Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade |
| 17 | Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats on old distempered work when shade is changed |
| 18 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 19 | Finishing walls with cement based water soluble exterior paint such as snowcem, robbiacem etc. two or more coats to give an even shade |
| 20 | Providing and laying vitrified floor tiles of different sizes in light colour shades made using Double Charge technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. Size 600x600 mm |
| 21 | Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading. |
| 22 | Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 450 x 310 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 23 | Providing and laying Polished Granite stone 18 mm thick flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 24 | 40mm thick white terrazo topping rubbed and polished to a granolithic finish under layer 28 mm thick cement concret 1:2:4 and top layer 12 mm thick with 7mm to 10 mm gauge white marble makrana chipping from indigenous marble laid in 3:1:6 (37.5 Kg of white cemet, 12.5 Kg marble powder and 0.05 cum of white marble chippings) |
| 25 | Providing and Laying Out Door precast designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement: 3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer-in-charge. |
| 26 | Supplying Pressed steel sheet frames (chowkhat) consisting of 18gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete Doors and windows frame of size 113mm x 60mm with 35 mm wide single rebate weighing 3.38 kg per meter. |
| 27 | Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter. |
| 28 | Factory manufactured Factory manufacturedsolid flush door fixed in position iron hinges, etc(excluding the cost of any fittings other than specifiedabove but including labour for fixing the same in position(Code : IS 2202-1(1999) Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 30mm thick |
| 29 | Chowkats of commercial Chowkats of commercialhard wood such as Hollockconfirming to ISI specificationno 1003 m kiln seasoned ofdoors and windows includingiron hold fasts, corner strapscleats, stops, bolts for holdfasts etc, complete fixed in position (Section 60mm x150mm) Single Rebate (60mm x 100mm) |
| 30 | Wire gauge Hollock wood door shutter without springs housed in chowkhat. 30 mm thick |
| 31 | Providing & fixing 6\\" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. |
| 32 | Providing & fixing 6\\" stainless steel tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. |
| 33 | Hollock wood doors shutter windows shutter including nhinges, screws, chocks, cheats, stops cords etc. complete fixed in position panelled, glazed or glazed and panelled. |
| 34 | First class burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. |
| 35 | Dismantling Sanitary fixtures such as Eurpoean/Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr complete in all respect as required by Engineer-in-Charge. Eurpoean/Indian/Orissa W.C., |
| 36 | ((b)) PVC / China Ware Cistern |
| 37 | ((c )) Wash Hand Basin / Urinal Pot |
| 38 | ((e)) CP Bib Cock/Angle Cock/Stop Cock/Shower/Bottle Trap |
| 39 | Dismantling, disjointing, removal of G.I. pipe lines, specials, valves and fittings complete in all respects.15mm internal diametre pipe line. |
| 40 | Providing, laying, jointing, fixing and testing ISI Marked uPVC Pipe with G.I. specials as per ISI-4985, including cost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete.uPVC Pipe 10 Kgf/cm2 20mm i/d |
| 41 | Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect. |
| 42 | Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect. |
| 43 | Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI makred including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 44 | Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI marked, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 45 | Providing & fixing in position vitreous Chinware white Indian make flat back or angular lipped front small urinals size 265x315x440mm approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect.approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect. |
| 46 | Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect. Size 550 mm x 400 mm x 815 mm |
| 47 | Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) Size 600mmx450mm |
| 48 | Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P.brass 15mm stop cock Male and female end |
| 49 | Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect. PVC tube connection of size 15 mm x 450 mm with C.P. Brass nut |
| 50 | Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. C.P brass towel ring |
| 51 | Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification of reputed firm of the self cleaning design with S.S. grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc. With 100mm x 75mm i/d Floor Trap (weighing 4.0 Kg) |
| 52 | Providing and fixing in position automatic brass Ball Cock in tanks. Brass Ball Cock with rod and Plastic Ball 20mm i/d |
| 53 | Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Triple Layer Tanks |
| 54 | Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.G.I. tank nipple 20mm i/d |
| 55 | Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect. |
| 56 | Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. C.P. brass Bib cock foam flow without flange |
| 57 | 12.5 mm thick cement plaster 1:4 |
| 58 | PROVIDING AND FIXING OF 12 MM THICK TOUGHENED GLASS |
| 59 | PROVIDING AND FIXING 8\\" ALDROPS |
| 60 | PROVIDING AND INSTALLATION OF 2 TON SPLIT AIR CONDITIONER 5 STAR RATING INCLUDING |
| 61 | ZEBRA BLINDS WITH FITTING AND INSTALLATION |
| 62 | PROVIDING AND FIXING SMART LED 55\\" OF SONY MAKE COMPLETE IN ALL RESPECT |
| 63 | PROVIDING AND FIXING STABLIZER 90V OF JHONSON MAKE COMPLETE IN ALL RESPECT |
| 64 | PROVIDING AND FIXING WALL FANS 400 MM OF ORIENT MAKECOMPLETE IN ALL RESPECT |
| 65 | Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper, slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1 cement and 3 fine sand) including replacing unserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50 m lead (The cost of new tiles or bricks excluded). |
| 66 | supply of new brick tiles size 22.86x11.43x3.81 cm |
| 67 | Dismantaling concrete cement concrete 1:2:4 mix CS |
| 68 | DUMPING OF BUILDING RUBBISH TO NEAREST DUMPING GROUND |
| 69 | CONCRETE Cement concrete 1:2:4 With stone ballast or shingle mixing by manual means |
| 70 | Wire brushing surface to remove all loose particles,dust,mould etc |
| 71 | RECESSED HGW CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copperconductor single core FR cable (ISI marked) overall 1.5sq.mm, 1100volts grade to be laid in heavy gauge weldedconduit pipe 20mm/ 25mm dia (1.6mm thick) ISI Marked,recessed in wall etc., complete with powder coated/anodized concealed metal boxes(1.6mm thick with Brass lugs) required for suitable numberof modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bellpush, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box an Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height. |
| 72 | RECESSED PVC CONDUIT PIPE WIRINGSYSTEM WITH MODULAR SWITCHES:Wiring in PVC insulated copper conductor single core FR cable marked) overall 1.5sq.mm, 1100volts grade to belaid in heavy gauge PVC conduit pipe 20mm/ 25mmdia. (ISIMarked) recessed inwall etc., complete withpowder coated/anodizedconcealed metal boxes(1.6mm thick with Brass lugs)required for suitable numberof modules (Modularaccessories) for having Steptype electronic fan regulators(two module) 100watts, bellpush, 6Amp. 2/3 universalsocket (shuttered),16/20Amp. combined/universal Socket (shuttered),6/10Amp. Switches,16/20Amp. switches withindicator etc. and coveredwith Frame Plate etc., PVCconnector (For Fan Box andCall Bell), Steel Hooks, Sheetmetal fan box (1.6mm thickshape hexagonal), Circularjunction Boxes (Four way PVC 1½\\" deep for walls and CI 3\\"deep for ceiling), bonding toearth with PVC insulatedcopper conductor single core FR cable (ISI marked) 1sq.mm, 1100volts grade (For6Amp. wall socket & plugcontrol point) and other pettymaterial etc., including thecost of above material, cuttingand filling up of chases (withfinishing the surface) Wiring fan point (Without fan box) |
| 73 | ((ii)) Wiring light point |
| 74 | ((iii)) Wiring call-bell point |
| 75 | ((iv)) Wiring 6Amp. wall socket point |
| 76 | ((vi)) Wiring 16/20Amp. power plug control point |
| 77 | PVC INSULATED FR COPPER CONDUCTORCABLES: Supply and erection of PVCinsulated FR single core Unsheathed copper conductorcable (ISI marked) suitable upto 1100 volts grade confirmto IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge Overall size 1sq.mm (Un-sheathed) |
| 78 | ((ii)) Overall size 1.5sq.mm (Un-sheathed) |
| 79 | ((iii)) Overall size 2.5sq.mm (Un-sheathed) |
| 80 | ((iv)) Overall size 4sq.mm (Un-sheathed) |
| 81 | ((v)) Overall size 6sq.mm (Un-sheathed) |
| 82 | XLPE INSULATED UN-ARMOURED CABLES (ON SURFACE): Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-Overall size 10sq.mm (2Core) Un-armoured (On-Surface) |
| 83 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Supply & erection of PVC Conduit Pipes (ISI marked) asper IS9537:Part-III & HDPE pipes (ISI marked) as perIS:4984:1995 for wiring purposes including bends,junction boxes, Steel hooks, M.S. saddle clamps and otherpetty materials etc., as perPWD General Specifications:- Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed) |
| 84 | A) MINIATURE CIRCUIT BREAKERS:Supply and erection of Miniature Circuit BreakerMCB's for circuit protection against overload and shortcircuit current fault suitable for 240/ 415 volts 50cycles ACsupply with breaking capacityof 10kA, Curve-C and low wattlosses as per IS/IEC 60898-1,nergy limitation class-3, true contact indication, label holderfacility in the existing MCB distribution board as per PWD General Specifications including connections withsuitable size of thimbles/lugs: MCB Single Pole 6-32amp. (10kA, Curve-C) |
| 85 | MCB Double Pole 50, 63amp. (10kA, Curve-C) |
| 86 | Supply and erection of RCBO (Residual Current BreakerOverload) for Earth leakage,overload and short circuit protection suitable for240/415 volts 50 cycles AC with breaking capacityof 10kA as per IEC 61009 inthe existing MCB distributionboard as per PWD GeneralSpecifications includingconnections with suitable size of thimbles/lugs:- RCBO Double Pole 63amp., Sensitivity 30mA |
| 87 | Supply and erection of sheet SP&N distribution board withprovision DP MCB's/ RCCB's/RCBO's as incomer and SPMCB's as outgoings and for TP&N horizontal distributionboard with provision TPN/ FP MCB's/ RCCB's/ RCBO's asincomer and SP MCB's as\outgoings) as per PWDGeneral specifications including connections withsuitable size of thimbles and bonding to existing earth etc:- SP&N Double Door Distribution Board 12 way each |
| 88 | SP&N Double Door Distribution Board 16 way each |
| 89 | TP&N Horizontal Double Door Distribution Board 4 way each |
| 90 | DISMANTLING WIRING POINTS & FITTINGS:Dismantling old wiring points including necessary repairs towall etc:- Fan, light or call bell point |
| 91 | Wall socket, power plug point |
| 92 | Providing and Fixing Chemical Earthing(copper type) with new Earthing Point,copper Wire including Testing and Labour Charges(2 METER) (Quotation) |
| 93 | LED Panels 36 Watt (White Light 2' x 2') |
| 94 | LED Round Panel 15 Watt 8 inch (Quotation rate) |
| 95 | Fine grassing including uprooting rank vegetation and weeds by digging the area to a depth of 30 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growth after 10 to 15 days, mixing fertilizer and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts, watering, weeding and maintenance for 30 days or till thick lawn is formed. Planting Selection no. 1 grass roots in rows 5 cm apart in both directions. Please Enable Macros to View BoQ information |
