|
| 1 | Supply of 2-way loudspeaker featuring a 15-inch woofer and a 1.75-inch High Frequency driver, Speaker type: 2-way Speaker, Bass-reflex Impedance : 8 Ohms, Sensitivity: 95 dB or higher RMS, PEAK-125 SPL, Power : NOISE-250 W, PEAK- 1000W or higher Frequency Range (-10 dB) : 49Hz - 20 kHz Enclosure : Plywood. of make Yamaha CHR 15 or any other similar reputed make as per Engineer in Charge. |
| 2 | Supply of Aluminum speaker stand, with steel locking pin of make AHUJA STA 150 or any other similar reputed make as per Engineer in Charge. |
| 3 | Supply of Dual Channel Power amplifier of type Class D with Power output 2 × 500 W @ 8 ohms,2 × 800 W @ 8 ohms, Frequency response:±1.0dB (1W, 8Ω, 20Hz to 20kHz) or better with Signal-to-noise ratio>100dB (A-weighted, 8Ω, Gain setting = +14dBu) of make YAMAHA of PX5 or any other reputed make as per Engineer in Charge. |
| 4 | Supply of Sub-woofer 15\\" Speaker Bass-reflex, Frequency range (-10dB):Passive: 33 Hz - 3.5kHz, Normal (*1): 35 Hz - 150 Hz, Extend (*1): 33 Hz - 150 Hz, POWER: NOISE 400W, PEAK 1600W, Nominal impedance: 8Ohm, SPL: Sensitivity (1W; 1m on axis)-98db PEAK-130db, I/O connectors-Speak ON NL4MP x 3 (Parallel x2, Output x1) of make YAMAHA CXS15XLF or any other similar reputed make as per Engineer in Charge. |
| 5 | Supply of Powered speaker with (Monitor Speaker)- Speaker type:2-way, Bi-amped Powered Speaker, Bass-reflex, Frequency range (-10dB): 48 Hz - 20 kHz, Maximum Output Level (Measured peak, IEC noise@1m): 129 dB SPL or Higher, Coverage area: H65ﾟ x V75, Amplifier Class: Class D, Power Rating: 1,000 W (LF: 800 W, HF: 200 W) *1. of make YAMAHA DHR12M or any other similar reputed make as per Engineer in Charge |
| 6 | Supply of Mixer with 12-Channel Mixing Console: Max. 6 Mic / 12 Line Inputs (4 mono + 4 stereo) / 2 GROUP Buses + 1 Stereo Bus / 2 AUX (incl. FX),24-bit / 192kHz 2in / 2out USB Audio functions, +48 Phantom power of YAMAHA MG12XU or any other Similar reputed make as per Engineer in Charge. |
| 7 | Supply of Dynamic super-cardioid vocal mic, which helps to reduce spill and feedback. Ideal for presentations, conferences, choirs, rehearsal rooms, and stage. Easily eliminates ambient noise. Superb high frequency reproduction Frequency response (Microphone) 50 to 15, 000 Hz Polar Pattern - Cardioid Output Impedance - 600 Ω Sensitivity - at 1 kHz, open circuit voltage -52 dBV/Pa¹ (2.5 mV)Not plastic, metal. No muffled, mids-centric sound but tight low mids and present treble. No problem with feedback, spill or handling noise; instead, maximum flexibility for the voice: it is a solid choice for performers. Frequency response (Microphone) 50 to 15, 000 Hz of make SHURE SV 200 or any other Similar reputed make as per Engineer in Charge. |
| 8 | Supply of table stand/Floor stand Microphone of Size: 350-530mm, base Dia-150mm. |
| 9 | Providing XLR to XLR cable of 15 mtr of reputed make as required by Engineer in Charge. |
| 10 | Providing SPEAKON to SPEAKON Cable 30 mtr of reputed make as required by Engineer in Charge. |
| 11 | Providing XLR to XLR cable of 1.5 mtr of reputed make as required by Engineer in Charge. |
| 12 | Supply of Wireless Dual Channel Hand Microphone - 2 hand mic I receiver. Dual Channel Non-Diversity, Frequency Response: 40Hz-16kHz, Polar Pattern: Cardioid of make STUDIO MASTER XR80HH or any other Similar reputed make as per Engineer in Charge. |
| 13 | Providing MIC stands Type: floor Stand, chrome Plated/ powder coated of required size of reputed make as required by Engineer in Charge. |
| 14 | Providing of Audio Rack for sound system Size: 935, W-600, D:560mm, Basic Frame: Steel, Front door: Lockable Toughen Glass, with Fan and Caster wheel of make NETRACK 17U or other reputed brand as required by Engineer in Charge. |
| 15 | Providing of Stabilizer of 50 KVA /5000W .Over and under voltage correction which automatically regulates in both conditions of make STUDIO MASTER SVC 5000 or other reputed brand as requied by Engineer in Charge. |
| 16 | Transportation ,Installation, testing and Commissioning of the Complete Sound System & Equipment's as required by Engineer in Charge. Please Enable Macros to View BoQ information |
