Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Civil Works , Plumbing & Sanitary works and Electrical works |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sq.m. on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto1.5m, as directed by Engineer-in-charge.All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20% |
| 6 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 7 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 8 | CEMENT CONCRETE (CAST IN SITU)1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size). |
| 9 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 10 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 11 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 12 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling, dressing & finishing the top smooth. |
| 13 | Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm. |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete |
| 15 | Walls (any thickness) including attached pilasters, butteressess, plinth and string courses etc. |
| 16 | Suspended floors, roofs, landings, balconies and access platform |
| 17 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 18 | Columns, pillars, piers, abutments, posts and struts. |
| 19 | Extra for shuttering in circular work (20% of respective centering and shuttering items) |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 21 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 22 | Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from naturalsources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | Reinforced cement concrete work in walls (any thickness), includingattached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up tofloor five level, excluding cost of centering, shuttering, finishing andreinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources) |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:4 (1 cement : 4 coarse sand). |
| 25 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 26 | Dry stone pitching 22.5 cm thick including supply of stones andpreparing surface complete. |
| 27 | Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab colour black, Cherry/Ruby redArea of slab over 0.50 sqm. |
| 28 | Providing edge moulding to 18 mm thick marble stone counters, Vanitiesetc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.Granite work |
| 29 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 30 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 31 | Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per requiredsize and pattern, finishing and sweeping extra sand. complete all asper direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approvedcolor design and pattern. |
| 32 | Stone work (machine cut edges Veneer work) for wall lining upto 10 mheight, backing filled with a grout of 12 mm thick cement mortar 1:3 (1Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement: 2 stone dust), including rubbing and polishing complete. (To be securedto the backing and the sides by means of cramps and pins which shallbe paid for separately).Kota stone slabs exposed face dressed and rubbed.25 mm thick |
| 33 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 34 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part-I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :35mm thick including ISI marked Stainless Steel butt hinges with necessary screw. |
| 35 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flates, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings / wooden frames with rawl plugs screws etc. |
| 36 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :125x64x2.50 mm |
| 37 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm |
| 38 | Providing and fixing bright finished brass handles with screws etc. complete:125 mm |
| 39 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 40 | Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm |
| 41 | Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 42 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 43 | Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge. |
| 44 | Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion(where ever required) extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming processof required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 45 | Providing and fixing factory made uPVC white colour casement/Casementcum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm). |
| 46 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm). |
| 47 | Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) |
| 48 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions and corners,all necessary fittings complete, including applying a priming coat ofapproved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 49 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-chargeProfile BFixing with adjustable lugs with split end tail to each jamb. |
| 50 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 51 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar,bent to shape with hooked ends in R.C.C. slabs or beams during laying,including painting the exposed portion of loop, all as per standard design complete. |
| 52 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt / Antiskid finish of sizeSize of Tile 600x600 mm |
| 53 | Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 54 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 55 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) |
| 56 | Barge board (Upto 300 mm) |
| 57 | 12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand) |
| 58 | 15 mm cement plaster on rough side of single or half brick wallof mix:1:4 (1 cement: 4 coarse sand) |
| 59 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer |
| 60 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 61 | Applying priming coat: STEEL & WOODEN SURFACEWith ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 62 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works. |
| 63 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 64 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 65 | Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 66 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 67 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 68 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, buttoms and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 69 | For shutters of doors, windows & ventilators including providing and fixing hings/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 70 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 5.50mm thickness. |
| 71 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 72 | Providing and applying intehral crystalline slurry of hydrophillic in nature for water proofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3:1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm per coat. |
| 73 | For horizontal surface one coat @ 1.10 kg per sqm. |
| 74 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Frame size 65 x 100 mm |
| 75 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)35 mm thick |
| 76 | Supplying and fixing C.I. cover with frame for manholes :500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg |
| 77 | Providing and fixing Mortise Cylindrical lock made of polished brass Make : Godrej or equivqlent |
| 78 | Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.(a). Brick on flat soling. |
| 79 | Supply , installation of Aerolam XLPE sheet with one side aluminium foil class - 1 of 19mm thick |
| 80 | Supplying, fitting and fixing Zebra blinds complete as specified and directed by the department at all levels. |
| 81 | Providing and fixing Buffet Counter 2400mm X 900mm, Two layer counter of 750mm and 1200 mm of height respectively as per design made in 19mm waterproof plyboard with 12mm waterproof plyboard backing, finish with 1mm premoum laminate of Merino/Greenlam/Century make. The Counter top to be finished with 18mm thick polished grantite. |
| 82 | Providing and Fixing Service Counter 1800mm X 1200mm X 600mm, made in 19mm waterproof plyboard with 12mm waterproof plyboard backing with 0.8mm inner laminate with 1mm premium laminate of Merino/Greenlam/Century make with bottom storage with Shutter. Complete with all hardware fittings of brash finish |
| 83 | Providing and fixing Wall paneling besides the glass window panels made in 19mm waterproof plyboard framework with 12mm waterproof plyboard covering with 1mm premium laminate finish over exposed surfaces of Merino/Greenlam/Century make. |
| 84 | Providing and fixing GI Planks ceiling with wooden Powder coated finish. Installated on U shape GI carrier hanged on GI Cable from true ceiling support, complete as per company guidelines |
| 85 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm witha pair of 15 mm C.P. brass pillar taps. |
| 86 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 87 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 88 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 89 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 90 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. |
| 91 | Providing and fixing bright finished brass hard drawn hooks and eyes300 mm |
| 92 | Providing and fixing toilet paper holder :C.P. brass |
| 93 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mmbreadth, weighing not less than 60 gms |
| 94 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 95 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore |
| 96 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 97 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore |
| 98 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm dia |
| 99 | 40 mm dia |
| 100 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming ro IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion.Single socketed pipes.110 mm diameter. |
| 101 | Providing and fixing wall faced unplasticised PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion.Coupler110mm |
| 102 | Bend 87.5°110mm bend. |
| 103 | Shoe (Plain)110mm Shoe. |
| 104 | Providing and fixing unplasticised PVC pipe clip of approved design to unplasticised PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required lingth, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm. |
| 105 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 grams. |
| 106 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.a) 15 mm dia |
| 107 | b) 20 mm dia |
| 108 | c) 25 mm dia |
| 109 | d) 32 mm dia |
| 110 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.EXTERNAL WORKa) 15 mm dia |
| 111 | b) 20 mm dia |
| 112 | c) 25 mm dia |
| 113 | d) 32 mm dia |
| 114 | e) 40 mm dia |
| 115 | f) 50 mm dia |
| 116 | g) 65 mm dia |
| 117 | i) 100 mm dia |
| 118 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore. |
| 119 | 40 mm nominal bore. |
| 120 | 65 mm nominal bore. |
| 121 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 122 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete withC.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 123 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 124 | Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required. |
| 125 | Providing, fixing, testing and commissioning of CP Brass Health Faucet with nuts, washers of approved brand including cutting and making good the walls wherever required. Rate of flow should be 4 LPM |
| 126 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 127 | Providing and fixing medium duty CP Floor grating with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required.a) 110mm dia |
| 128 | Providing and fixing medium duty CI grating (for RWP) with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required.a) 110mm dia |
| 129 | Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required.a)110 mm O.D type \\"B\\" |
| 130 | Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required.a) 110 od |
| 131 | Fixing automatic high pressure electric water heaters with glass lining thermostats with each element and high temperature cut off, necessary insulation, safety valve, 15 mm dia 600 mm long flexible pipe etc., all complete. Make :Havells / Jaquar or Equivalent.a) 50 Ltr Capacity |
| 132 | Providing of SS304 grade water dispenser with hot and cold water facility having a cooling capacity of 150 litres/Hour, 3 faucets, with power requirement of 230V/50Hz/1Phase (Make : Blue Star or equivalent) |
| 133 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with1.5 sq.mm FRLS PVC insulated copper conductor single core cablein surface / recessed medium class PVC conduit, with modularswitch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc.as required.Group A |
| 134 | Group B |
| 135 | Group C |
| 136 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B |
| 137 | Group C |
| 138 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 139 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 140 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 141 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 142 | 4x10 sq.mm + 2x6 sq.mm earth wire |
| 143 | 4x16 sq.mm + 2x6 sq.mm earth wire |
| 144 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20mm |
| 145 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch |
| 146 | 15/16 A switch |
| 147 | 3 pin 5/6 A socket outlet |
| 148 | 6 pin 15/16 A socket outlet |
| 149 | Bell push |
| 150 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required |
| 151 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 152 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm) |
| 153 | 3 Module (100mmX75mm) |
| 154 | 6 Module (200mmX75mm) |
| 155 | 12 Module (200mmX150mm) |
| 156 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 157 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way, Double door |
| 158 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator.6 way (4 + 18), Double door |
| 159 | 8 way (4 + 24), Double door |
| 160 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 161 | Double pole |
| 162 | 40A & 63A 4P MCB |
| 163 | Modification in existing panel to add 63A 4P MCB (10KA) in existing panel at site complete as required with all the necessary accessories etc. |
| 164 | Supply, Installation, testing and commissioning of following rating solid state INVERTOR with sealed maintenance free batteries suitable for delivering full power for 1.5-2 hours including supplying suitable cabinet and stand to allow heat dissipation. If the following ratings are not available next higher rating should be provided:1.5kVA Solid state inverter including battery bank |
| 165 | Supplying and fixing of Philips/ Kolors or equivalent LED round fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED Round Light,12W |
| 166 | Supply, fitting, fixing of LED Tube Light 20W with connection. Bajaj or Kolors or equivalent as required. |
| 167 | Supply, fitting, fixing of 2x2 LED Light 30W with connections. Bajaj or equivalent as required. |
| 168 | Supply, fitting, fixing of high speed A.C. ceiling fan, complete with all accessories down rod, canopy etc. of following sweeps with making necessary connections atc.as required complete and as directed by the department (without regulator).1200 mm sweep |
| 169 | Supply, fitting, fixing of enegy efficent A.C. Exhaust fan in the existing hole on the wall of following sweeps and making necessary connections etc., as required complete and as directed by the Department.Heavy duty for 900/ 960 rpm300 mm sweep |
| 170 | AIR CONDITIONING OF DINING HALLVRV / VRF AC SYSTEM Supplying, installation, Testing & commissioning of VRV/VRF system including indoor / oudoor units, piping, electrical power distribution/wiring, electrical panel, treated fresh air system etc.Type of Air Conditioner : Ceiling mounted 4 way Cassette Inverter type AC unit X 4 Nos. Capacity (Tonnage) : 3.50 Tr Make : CARRIER / TOSHIBA / GENERAL / BLUESTAR / DAIKIN OR EQUIVALENT - 5 Star rated |
| 171 | Commerical kitchen (SS items)Supply, fabrication, and installation of following items made of high-quality stainless steel (SS 304 grade), comprising of adequate number of shelves for storage of utensils/dishes. The cabinet shall be of robust construction with smooth finish, corrosion-resistant, and easy to clean. It shall be provided with hinged/sliding doors, proper locking arrangement, ventilated design where required, and supported on SS legs with adjustable feet. All edges shall be machine-finished to avoid sharp corners.The work shall include all necessary fittings, fixtures, hardware, and accessories complete in all respects as per approved design and direction of the Department.THREE BURNER INDIANSize / Capacity: 60\\"X28\\"X34\\"+6\\" |
| 172 | SINGLE SINKSize / Capacity: 24\\"X28\\"X34\\"+6\\" |
| 173 | WORK TABLE WITH 2 BOTTOM SHELVESSize / Capacity: 46\\"X28\\"X34\\"+6\\" |
| 174 | DISH STORAGE CABINETSize / Capacity: 54\\"X14\\"X34\\" |
| 175 | DISH STORAGE CABINETSize / Capacity: 60\\"X14\\"X34\\" |
| 176 | EXHAUST HOOD WITH LIGHTSupply, fabrication, and installation of exhaust hood with inbuilt lighting system suitable for commercial kitchen application.The hood shall be fabricated from food-grade stainless steel (SS 304) with minimum 1.2 mm thickness for outer body and 1.0 mm thickness for internal parts, ensuring durability, corrosion resistance, and hygienic performance.The exhaust hood shall be of canopy type, designed for efficient extraction of heat, smoke, fumes, and grease vapours, and shall be provided with: • High-efficiency SS baffle filters, removable and washable • Grease collection channel with drain outlet and oil collection tray • Provision for duct connection with suitable collar/flange • Factory-fitted LED light fixtures (vapour-proof type) for adequate illumination • Smooth hairline/matte finish with properly polished surfaces • Machine-rounded edges for safety and ease of maintenanceThe hood shall be mounted using suitable MS/SS supporting frame or hanging arrangement, complete with anchor fasteners and necessary hardware.The item includes all materials, fittings, accessories, labour, and installation complete in all respects as per manufacturer specifications and direction of Engineer-in-Charge.Size / Capacity: 20FT8\\"X42\\"X18\\" |
| 177 | EXHAUST HOOD WITH LIGHTSupply, fabrication, and installation of exhaust hood with inbuilt lighting system suitable for commercial kitchen application.The hood shall be fabricated from food-grade stainless steel (SS 304) with minimum 1.2 mm thickness for outer body and 1.0 mm thickness for internal parts, ensuring durability, corrosion resistance, and hygienic performance.The exhaust hood shall be of canopy type, designed for efficient extraction of heat, smoke, fumes, and grease vapours, and shall be provided with: • High-efficiency SS baffle filters, removable and washable • Grease collection channel with drain outlet and oil collection tray • Provision for duct connection with suitable collar/flange • Factory-fitted LED light fixtures (vapour-proof type) for adequate illumination • Smooth hairline/matte finish with properly polished surfaces • Machine-rounded edges for safety and ease of maintenanceThe hood shall be mounted using suitable MS/SS supporting frame or hanging arrangement, complete with anchor fasteners and necessary hardware.The item includes all materials, fittings, accessories, labour, and installation complete in all respects as per manufacturer specifications and direction of Engineer-in-Charge.Size / Capacity: 25FTX42\\"X18\\" |
| 178 | WORK TABLE WITH 2 BOTTOM SHELVESSize / Capacity:40\\"X26\\"X34\\" |
| 179 | WORK TABLE WITH SINKSize / Capacity:: 32\\"X28\\"X34\\"+6\\" |
| 180 | TRAY TROLLEY RACKSize / Capacity:: 18\\"X28\\"X60\\" |
| 181 | WORK TABLE WITH SINKSize / Capacity:: 44\\"X24\\"X34\\"+6\\" |
| 182 | WORK TABLE WITH 2BOTTOM SHELVESSize / Capacity:: 60\\"X24\\"X34\\"X6\\" |
| 183 | TWO DOOR VERTICAL CHILLERSupply of hard top chest freezer of approximately 628 litres capacity, operating on eco-friendly R290 refrigerant, with manual defrost system, two vertical doors,of 4 shelves with locking facility. The unit shall be convertible type with embossed inner liner, provided with caster wheels and provision for defrost water drain. The freezer shall operate on 230V AC, 50Hz, single phase power supply withtemperature range -2 Degree to -12 Degree celc. and other specifications as per direction of department.Size / Capacity:: 28\\"X28\\"X80\\" |
| 184 | WORK TABLE WITH SINKSize / Capacity:: 50\\"X24\\"X34\\"+6\\" |
| 185 | WORK TABLE WITH 2 BOTTOM SHELVESSize / Capacity:: 42\\"X24\\"X34\\"+6\\" |
| 186 | VEGETABLE STORAGE RACK - 6 BASKETSize / Capacity::50\\"X20\\"X60\\" |
| 187 | ONION/POTATO BINSize / Capacity: 44\\"X20\\"X24\\" |
| 188 | STORAGE RACK - 5 SHELFSize / Capacity: 36\\"X20\\"X72\\" |
| 189 | WALL SHELFSize / Capacity: 54\\"X12\\"+18\\"X15\\" |
| 190 | DRAIN GRATINGSize / Capacity:30\\"X14\\"X3\\" |
| 191 | TWO DOOR VERTICAL FREEZERSupply of hard top chest freezer of approximately 628 litres capacity, operating on eco-friendly R290 refrigerant, with manual defrost system, two vertical doors,of 4 shelves with locking facility. The unit shall be convertible type with embossed inner liner, provided with caster wheels and provision for defrost water drain. The freezer shall operate on 230V AC, 50Hz, single phase power supply withtemperature range -7 Degree to -25 Degree celc. and other specifications as per direction of department.Size / Capacity:28\\"X28\\"X80\\" |
| 192 | HARD TOP CHEST FREEZERSupply of hard top chest freezer of approximately 301 litres capacity, operating on eco-friendly R290 refrigerant, with manual defrost system, double swing/hinge type doors, and single storage compartment with locking facility. The unit shall be convertible type with embossed inner liner, provided with one basket, caster wheels for mobility, and provision for defrost water drain. The freezer shall operate on 230V, 50Hz, single phase power supply with power consumption of approximately 168 watts and shall support stabilizer-free operation. Inbuilt lighting is not required. The product shall be manufactured in India and supplied complete with standard manufacturer support. Size / Capacity: 300LTR. |
| 193 | GARBAGE BINSize / Capacity: 65LTR. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
