|
| 1 | Surface excavation in hard and dense soil n.exc 30 cm deep and averaging 15 cm deep and getting out, complete all as specified and directed. |
| 2 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed. |
| 3 | Returning, filling in, hard and dense soil inluding spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25cm thick each in trenches, after the pipes have been laid and tested, complete all as specified and directed. |
| 4 | Removing excavated material soft/loose soil exc 50 m but not exc 250 m deposited where directed at a level n.exc 1.5 m above the starting point for soil, complete all as specified and directed. |
| 5 | M&L for plain cement concrete type D-2 1:4:8 (40 mm graded crushed stone aggregate) as in foundation or sub base, complete all as specified and as directed. |
| 6 | M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed. |
| 7 | M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate as in columns and pillars etc complete all as specified and as directed. |
| 8 | M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. |
| 9 | M&L for steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surface of concrete, complete all as specified and as directed. |
| 10 | M&L for steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal shape for fair finished surface of concrete, complete all as specified and as directed. |
| 11 | M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and as directed. |
| 12 | M&L for steel from work to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces, complete all as specified and as directed. |
| 13 | M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, Fe 550 D grade complete all as specified and as directed. |
| 14 | All as per srl item no 13.00 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, complete all as specified and as directed. |
| 15 | M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed. |
| 16 | M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed. |
| 17 | M&L 15 mm thick ready mix plaster (self curing) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specifed and directed. |
| 18 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth withot using extra cement. |
| 19 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth withot using extra cement. |
| 20 | M & L for rendering 10 mm thick on surfaces of ceiling in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified and as directed. |
| 21 | M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed. |
| 22 | M&L for preparation of newly plastered surfaces of wall and applying 1 to 2 mm thick wall care putty on whole surfaces including grinding with sand paper and levelling of surface and applying two coat of oil bound distemper on white or tinted over existing prepared putty base surface, complete all as specified and as directed. |
| 23 | M&L for preparation of newly plasered surfaces of ceiling and applying three coat of white wash, complete all as specified and as directed. |
| 24 | M&L for hardcore of base not exceeding 63 mm of broken stone or bolder, deposited, spread and leveled in layers not exceeding 15 cm thick watered and rammed to a true surface, complete all as specified and as directed. |
| 25 | M&Lfor 40 mm thick cement concrete 1:2:4 type B1 (Using 20mm graded crushed stone agg), as in sub base in floor/paving etc complete all as specified and as directed. |
| 26 | M&L for moorum/ red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed. |
| 27 | M&L for 100 mm thick cement concrte 1:4:8 type D2 ,using 40mm graded stone aggregate, as in sub base o flooring etc, complete all as specified and as directed. |
| 28 | M&L for 75 mm thick cement concrte 1:4:8 type D2 ,using 40mm graded stone aggregate, as in sub base o flooring etc, complete all as specified and as directed. |
| 29 | M&L for first quality non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors over and including 15 mm thick cement screed bed in cement mortar (1:6), set and jointed in neat cement slurry at the rate of 3.0 kg per sqm and pointed in white/coloured cement to match the shade of tiles, complete all as specified and directed. |
| 30 | M&L for first quality non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, as in floors laid on 15mm thick cement screed bed in CM (1:6), set and jointed in neat cement slurry at the rate of 3.0 kg per sqm and pointed in white/coloured cement to match the shade of tiles, complete all as specified and directed. |
| 31 | M&L for glazed ceramic coloured tiles of 300x450x7mm thick, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over 10mm thick cement plaster in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed. |
| 32 | M&L powder coated aluminium (minimum thickness of powder coating 50 microns) three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified and as directed.. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately. |
| 33 | S&F powder coated aluminium (minimum thickness of powder coating 50 microns) ventilator with outer frame 40mmx114mm with 1.3mm thickness corner 45 degree cut & aluminium welded center mullion size 40mmx65mm partly glazed/ gauzed including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws , MS wire mess , 3mm thick sheet glass etc. provision for fixing the exhaust fan complete all as specified and as directed. |
| 34 | S&F factory made solid WPC (wood polymer composite) door frame 125mmx65mm double rebated made from WPC (single extruded process) material comprisin of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 780 kg/cum, having good screw holding capacity (screw withdrawl strength of min 990 N), min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing in position with SS Dash fasteners/ hold fast of required dia and length, complete all as specified and as directed |
| 35 | S&F factory made single extruded WPC (wood polymer composite) solid door frame of size 100mmx65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fiber (wood powder/ rice husk/ wheat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100n (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant, complete all as specified and directed |
| 36 | S&F factory made single extruded WPC (wood polymer composite) soild plain flush door shutter of 30mm thick comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100N (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/MM2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and supply & fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk SS screw, complete all as specified and directed |
| 37 | S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and supply and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. |
| 38 | S&F 35mm thick FACTORY MADE B/S PRELAM WIRE MESH SOLID PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rails. M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded Prelam sheet 'C' channel made from 5mm (±0.25) thick PVC Sheet of Density 600 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, of size 35mm thickness, 115mm width out of which 100mm shall be flat and 15mm shall be bent in 90° angle on either side forming stiles,one of the 90° bend edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws. 5mm (±0.25) thick 140mm wide PVC sheet out of which 125mm shall be flat and 15mm shall be bent in 90° on the inner side to form top and bottom rail and 155 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90° on both side to form lock rail. An additional 5mm (±0.25) thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent cement adhesive. Panel will be of GI /SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top, bottom & lock rail is sealed with 15mm x15mm tube with steel screw of size 13/6 mm.10mm (5mm x 2nos) thick PVC strip of 25mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top, bottom & lock rail. 10mm thick (5mm x 2nos) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm x 25mm x 2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardware’s should be fixed with 19 x 6mm size steel screws etc. Complete as per direction of Engineer-in -charge. |
| 39 | S&F 150mm long stainless steel AISI 304 barrel tower bolts, complete as specified and directed |
| 40 | S&F 200mm long stainless steel AISI 304 barrel tower bolts, complete as specified and directed |
| 41 | S&F 150mm size stainless steel AISI 304 handles, complete all as specified and directed |
| 42 | S&F 250mm long stainless steel AISI 304 sliding door bolt with staple (bolt type) and fixing clips and fixing bolts and sliding bolts, complete all as specified and directed |
| 43 | S&F vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and directed. |
| 44 | S&F PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level, complete all as specified and directed. |
| 45 | S&F vitreous china wash basin, white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed by engineer-in-charge. |
| 46 | S&F in repair vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and directed by engineer-in-charge. |
| 47 | S&F 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooded plugs with chromium plated brass screws and cup washers, complete all as specified and directed by engineer-in-charge. |
| 48 | Supplying and fixing of 15 mm bore UPVC pipes SDR 11 & plain CPVC SCH-40 fitting on walls /ceiling or laying in floors including all fitting such as ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor complete all specified and directed by Engr-in-Charge |
| 49 | S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed by engineer-in-charge. |
| 50 | S&F ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed, complete all as specified and directed by engineer-in-charge. |
| 51 | S&F gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and directed by engineer-in-charge. |
| 52 | S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and directed by engineer-in-charge. |
| 53 | S&F 15 mm angle valve/ stop valves, cast copper alloy, chromium palted, fancy type screwed down high pressure with crutch and butter fly handles , screwed with iron pipes or for union, complete all as specified and directed by engineer-in-charge. |
| 54 | S&F bib tap, brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore, complete all as specified and directed by engineer-in-charge. |
| 55 | S&F pillar tap, brass chromium plated fancy type with capstan heads, screwed down high pressure, screwed for iron pipe 15 mm bore, complete all as specified and directed by engineer-in-charge. |
| 56 | S&F chromium plated grating with 100mm dia of approved make includingh fixing with 1:4 CM to floor/ nahni trap etc., complete all as specified and directed by engineer-in-charge |
| 57 | S&F brass chromium plated tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass CP, complete all as specified and directed by engineer-in-charge. |
| 58 | S & F PVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 59 | S & F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 60 | S & F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints laid in trenches, complete all as specified and directed. |
| 61 | S&F for PVC (SWR) bends any radius, 110 mm bore complete. |
| 62 | S&F for PVC (SWR) bends any radius, 75 mm bore complete. |
| 63 | S&F for 75 mm bore PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in solvent cement concrete complete all as specified and as directed. |
| 64 | S & F Stack clamps to hold for 110mm dia PVC rain water with wall made out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete. |
| 65 | S & F Stack clamps to hold for 75mm dia PVC rain water with wall made out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete. |
| 66 | S&F in repairs 180mm x 150mm salt glazed stone ware gully traps square & round mouthered trap 'P' including case iron grating and fixed, including necessary excavation and earthwork, concrete in bed, surrounds, kerbs etc., and jointing to drains in CM 1:1, complete all as specified and directed by engineer-in-charge. |
| 67 | M&L for roof treatment in following stages, complete all as specified and directed by engineer-in-charge.(i) Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete . (ii) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 Kg per sqm including cleaning surfaces(iii) APP polymeric water proofing membrane minimum 3 mm thick and wieghing not less than 3.0 Kg per Sqm , black finish reinforced with non woven polyester matt with a thermo fasable finish laid over bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butrane gas torch with an overlap of 100mm at the sides and 150mm at the ends, as per manufacturers instructiions incl preparation of surface and applying two coats of aluminium paint over membrane (Manufacturer as approved by GE). |
| 68 | M&L for providing and injecting chemical chlorpyrifos emulsifiable for pre constructional anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes, complete all as specified and directed by engineer-in-charge. |
| 69 | M&L for anti termite treatment of soil under existing floors using chemical chlorpyrifog emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floors, complete all as specified and directed by engineer-in-charge. |
| 70 | Plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping and similar work etc. including weathering, slightly rounded or chamferred angles and throating and provision of necessary formwork, complete all as specified and directed |
| 71 | S&F in repair factory made SFRC manhole cover of any size any shape (square/rectengular/circular) etc 70mm thick with frame set in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.Note:- Make of SFRC Manhole/drain cover:- (a) M/s PS Concrete.(b) M/s KK Manhole.(c) BRHL Concrete Industries. |
| 72 | Material & Labour for 170mm nominal size (DWC HDPE) Double wall corrugated high density polyethylene pipe (SN-8) confirming to IS 16098 pipes including all fixing accessories laid in trenches and jointed complete all as specified and directed |
| 73 | Material & Labour concrete bed to 170 mm bore drain pipes in cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified. |
| 74 | Extra over surface channel inside of manholes for forming fair finished drains of channels 30 cm inner girth in cement concrete using extra cement inclding forms, moulds, mitred/stopped ends, complete all as specified and directed. Note : Inner girth only be measured and paid. |
| 75 | S&F Steel work in tubular trusses including special shaped/ semi arch washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240. complete all as specified and directed by Engr-in-charge. |
| 76 | S&F Framed work such as grills, gratings, MS angle etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 77 | M&L for preparation of new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer, complete all as specified and directed. |
| 78 | Providing Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) JALI of required size comprising of virgin PVC resin of K Value 58-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC Jali to be fixed with stainless Steel butt hinges ( if required ) of required size with necessary full body threaded star headed counter sunk SS Screws including cutting of holes design all as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For Interiors / Kitchen shutters / Balcony & Internal Doors and Partitions. |
| 79 | M&L for Glossy finished pre-polished coloured machine pressed precast concrete interlocking paver block any shpe and size confirming to IS 15658-2006 of 60 mm thickness , M-35 grade with grey cement and pigments over and including 50 mm thick sand cushioning complete all as specified and as directed. |
| 80 | M&L precast cement concrete solid building blocks or slabs exc 10cm thick Type B1 1:2:4(20mm graded aggregates) (with plain or interlocking joints as directed) setting in mortar, complete, in walls set in CM 1:4 complete all as specified and as directed. |
| 81 | S&F powder coated (minimum thickness of powder coating 50 microns) aluminium frame for partitions,doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 82 | S&F aluminum powder coated (minimum thickness of powder coating 50 microns) door shutter, aluminium section weighing not less then 0.55 Kg/m incl necessary jointing cleats, glazing clips rubber neoprene packing incl (a) 150mm handle - 02 Nos (b) Stainless steel hinges - 100mm - 03 Nos (c) Mortice lock in built 3 lever-01 Nos (d) handle 150mm- 2nos in each shutter, alum anodized snap beading screw etc complete all as specified and as directed.Note: Glass & ACP sheet shall be paid measured and separately. |
| 83 | S & F 4.8 mm thick tinted glass fixed to aluminum frame work with rubber beading gasket complete all as specified and directed. |
| 84 | S&F 5-6 mm thick ACP sheet, prelaminated both side with decorative choice lamination, fixed with rubber beading fixed to aluminum framing all as specified and directed. |
| 85 | Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete. |
| 86 | Supplying, installing, testing and commisioning automatic/sensor Sliding 12mm thick frameless toughened Glass Door (bi-parting) of hight upto 2400mm and width upto 3600mm driven by Electro-mechanical geared DC brushless motor (approx. 40W-55W) with operator housing of Aluminum profile track/channel (upto. 3.6m length for double doors incl Microwave motion sensors (for activation) and Infrared safety sensors (to prevent closing on objects), Toothed belt drive system with micro-processor based controller with Automatic reverse on obstacle detection, emergency manual release, and <50 dB silent operation complete including cutting holes, edgess rounded and etching works etc and all kind of SS patch fitting & fixture, spinder patch etc.including taking down of old doors of any type and size all as specified and as directed by engineer in charge. |
| 87 | Excavating in post holes (or similar holes) each n.exc 0.50 cum getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering and removing surplus soil n.exc 50m and making good the surface in any type of soil. |
| 88 | S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete alll as specified and as directed. |
| 89 | M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated single core unsheathed FRLS 1100 volts grade electrical cable drawn existing concealed PVC conduit in wall and ceiling and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes of min thickness 1.2 mm with 120 GSM Zinc coating including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable Single core PVC insulated unsheathed earth continuity wire to common earth and connected to earth dolly complete all as specified and directed.Note (a): The rates are inclusive of providing point wiring on casing caping if there is blockage/damage in existing conduit on ceiling.(b) :The rates are inclusive of cutting / chasing and making good disturbed surface with CM 1:3. |
| 90 | All as per item No 117.00 here-in-before but One socket outlet 5 Amps on same board. |
| 91 | All as per item No 117.00 here-in-before but One socket outlet 5 Amps on independent board. |
| 92 | All as per item No 117.00 here-in-before but One socket outlet 15 Amps on independent board and through new concealed conduit complete with 2.5 sqmm size. |
| 93 | S & F Switch Modular type switch, 6 A 1- way 1 Module switch with finger proof terminal complete all as specified and directed. |
| 94 | S & F modular type 2/3 pin combined shuttered type 6A socket 2 Module complete all as specified and directed. |
| 95 | S & F Switch Modular type switch, 16 A 1- way 1 module switch with finger proof terminal complete all as specified and directed. |
| 96 | S & F modular type 2/3 pin combined shuttered type 16 A socket 2 Module,complete all as specified and directed. |
| 97 | S & F AC modular fan regulator 120 W 2 module complete all as specified and directed. |
| 98 | S & F ceiling rose 3 terminal complete all as specified and directed. |
| 99 | S&F surface mounting LED Integrated Aluminum Batten luminaries Polycarbonate co-extrusion tube for Not less than 20 Watt LED light housing 4 feet . Fixture should have minimum system lumen of 2000lm & minimum efficiency at system level >=120 lumens/Watt, life of fixture 50K Hrs, CCT 4000-6500K with same lumens/w CRI>80, PF>0.95 THD<10% @ 240V AC An operating voltage Range of 140-270V including all connection up to ceiling rose complete all as specified and directed. |
| 100 | S&F surface mounting LED Integrated Aluminum Batten luminaries Polycarbonate co-extrusion tube for Not less than 10 Watt LED light housing 2 feet . Fixture should have minimum system lumen of 2000lm & minimum efficiency at system level >=120 lumens/Watt, life of fixture 50K Hrs, CCT 4000-6500K with same lumens/w CRI>80, PF>0.95 THD<10% @ 240V AC An operating voltage Range of 140-270V including all connection up to ceiling rose complete all as specified and directed. |
| 101 | S & F 35 Watt street light high efficiency long life LED module with LENS type LED package mounted on MCPCB, Fixture should have minimum efficiency at system level >=120 lumens/Watt, integral SMPS based constant current electronic LED driver with THD<10% surge voltage protection of > 5.0 KV, CRI>80, PF>0.95,CCT 4000-6500K and other safety tests as per IS:15885( part-2/sec-13),IP 66 protection high efficiency polycarbonate cover with integrated lens housed in pressure die cast aluminim alloy heat sink for effective thermal management strudiness excellent corrosion resistance separate optical and control gear compartment & Top opening for easy maintanance suitable for side entry wall mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible copper cunductor cable of appropriate size and 1.5m long bracket having 40mm diameter light grade GI pipe including GI clamp nuts bolts & washers with two coats of synthetic enemal paint over a coat of oxide primer complete all as specified and directed. |
| 102 | Supply, Installation, testing and commissioning of 1200mm sweep BEE 5 star rated, Ceiling fan with remote control, Brush Less Direct Current (BLDC) Motor, Class of insulation : B, 3 Nos Blade, 30 cm long down road, 2 Nos canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery not less than 220 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%, and all remaining accessories including safety pin, nuts bolts, washers, temperature rise =75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50 Hz, single phase AC supply complete including taking down and keeping in safe coustody and depositing it to MES store yard complete all as specified and directed. |
| 103 | Supply and fix in replacement of SPN 8 Way double door mettalic DB with rubber gasket conforming to IEC 61439-3 suitable for flush / surface mounting having 100 A copper busbar fully shrouded neutral bar earth bar wire set & cable ties for cable management pre fiited sheet etc. Having IK 09 & IP 43 protection complete including taking down of old DB all as specified in IS 732:2019 complete all as specified and directed. |
| 104 | M&L in replacement MCB SPN 'C' curve 40 Amps 240 Volts , 10 KA complete all as specified and directed. |
| 105 | M&L in replacement MCB SP 'C' curve 06 to 32 Amps 240 Volts 10 KA complete all as specified and directed. |
| 106 | S &F in replacement for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in drg and connected to earth test point including testing complete all as specified and directed. |
| 107 | M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4.0 Sqmm, 450/1100 Volts grade on & including PVC Conduit 25 mm medium grade complete with conduit accessories and copper cable 4.0 sqmm continuous earth wire complete all as specified and directed (Two runs of cable with 01 earth wire shall be measured as one length) |
| 108 | Supply and fix in repair of GI pipe's bracket suitable for fixing of bldg security LED light fitting of 45 Watts including grouting and fixing the same on wall for installation of light fitting with necessary clamps, nut, bolts & washer and painting by synthetic enameled good quality paint in white/grey colour over one coat of red oxide primer until unless smoothness of bracket complete all as specified and as directed.Note :- GI pipe should be 25 mm bore with medium grade and the same to be moulded in 45 degree angle at the 1m height to fix the building security light fitting. |
| 109 | Supply and laying dry river sand laid in trenches as cable cushioning and covering complete all as secified and directed. Note : Punned thickness only measured and paid. |
| 110 | M & L for brick well brunt locally available sub class'B' laid over sand cushioning to cable in trenches keping width of brick parallel to the length of cable complete all as specified and directed. |
| 111 | Supply and laying in repair of XLPE insulated,sheathed,armoured,heavy duty LT 1100 volts grade cable 25 Sqmm 3.5 core with aluminium conductor laid in trenches/pipes, fixed to poles/walls with suitable saddle aluminium lugs, gland if required and jointed complete all as directed. |
| 112 | Supply and Laying of PPR pipes 3- layer SDR 7.4 of outer diameter of pipes as following UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plain & brass threaded polypropylene random fittings laid in trenches including fittings and testing complete all as specified and directed. |
| 113 | (a) 25 mm dia. |
| 114 | (a) 32 mm dia. |
| 115 | M&L for construction of Brick Masonry valve chamber of size 600x600x600mm (Internal dimensions) with PCC 1:4:8 foundation 150mm thick, brick work built in CM 1:6, PCC 1:3:6 coping 50mm thick, plastering 15mm thick in CM 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 4mm thick and MS equal angle iron 50mmx50mmx6mm frame as per existing size with locking arrangement embedded in PCC suitable for 25/40/50mm gate valve and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete including dismantling old/damaged valve pits. complete all as specified and directed. |
| 116 | M&L for making connection of PPR distribution branch with PPR main of sizes 25 mm to 50 mm by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed. |
| 117 | Supply and fixing PPR gate valve (brass insert) of size 25 mm dia including connection and testing complete all as directed. |
| 118 | Supply and fixing PPR gate valve (brass insert) of size 32 mm dia including connection and testing complete all as directed. |
| 119 | S&F GI Flat strip clamps of size 25mm x 3mm duly bended as per the size of GI tubing and site condition, drilled complete all as specified and directed. |
| 120 | Supply and fixing of heavy rust proof passivated bolts made of steel of size 8 mm dia 75 mm long including necessary drilling on wall for fixing of steel frame complete all as specified and directed. Please Enable Macros to View BoQ information |
| 121 | Supply and fixing of heavy rust proof passivated bolts made of steel of size 8 mm dia 75 mm long including necessary drilling on wall for fixing of steel frame complete all as specified and directed. Please Enable Macros to View BoQ information |
